WITSEER M1 Home Projector User Guide

M1 Home Projector
User Guide

Welcome to WITSEER Home projection!

Please read this user manual carefully before embarking on a new home experience with WITSEER, for your safety and benefit. WITSEER shall not be liable for any personal injury, property or other damage caused by your failure to follow the instructions or precautions.
Due to the update and upgrade of the product, the actual product and the schematic diagram may be slightly different, please refer to the actual product. Please keep it safe for later use.
If you have any objection to any of the contents or terms of the manual, please submit a written objection to WITSEER within seven days after purchasing the machine, otherwise you will be deemed to have agreed, understood and accepted all the contents of this manual. WITSEER reserves the right to interpret and amend the specification finally.

|
---|---

Important considerations

• Do not point the lens directly at the human eye to avoid damage to the eyes caused by the strong light of the lens after turning on;
• Do not block the inlet/outlet of the machine, ensure that there is no obstruction within 25cm next to the inlet/outlet of the machine, to avoid damage to the internal electronic devices caused by the normal hostile heat of the machine, or affect the normal service life of the machine;
• Do not clean the machine with chemicals, detergent water, and avoid rain, moisture and liquids containing minerals to corrode the circuit board;
• Do not touch this machine or the remote control when the human body is wet; Please ensure that the machine is used in a dry and ventilated environment, such as the machine is not allowed to be used after flooding;
• Replacing with the wrong model battery is a risk of explosion, be sure to dispose of used batteries according to the instructions;
• Do not store the machine in a place that is too hot or cold, high (low) temperature will shorten the life of the electronics. The ambient temperature allowed for machine storage is -20″C-60°C, and the use of the the rmobase is -10″C-35°C;
• Do not use a non-standard power adapter to power the machine;
• Please use the battery model described in this manual for the remote control, if the wrong model of battery is used, it may cause damage to the remote control or the machine;
• Do not place the working machine on flammable substances such as beds or blankets;
• Please hurriedly put the machine into any heating machine (such as dryer, corrugated oven, etc. for drying):
• Do not squeeze the machine too hard to place heavy objects on top of it:
• Do not throw, knock or shake the machine strongly to avoid damage to the internal circuit board:
• Do not attempt to disassemble and repair the machine without permission. If you have any questions, please contact the channel where you purchased the machine or the official customer service;
• If the machine is not used for a long time, please shut down and cut off the power;
• Please do not use third-party ROOT flashing or unofficial source system packages to update this machine, which may cause irreversible problems.

Projection method

Two projection methods

When changing the projection mode, please turn off the projector first, and then turn on the projector after the installation is complete. Select the projection mode in system Settings-Image Settings-installation mode.

Frontal projection
Taking the default front projection mode as an example, we recommend that you place the machine horizontally in front of a flat white wall or curtain 10cm- 30cm, and the center of the screen should be flat at the height of your eyes, which will provide you with the best viewing experience.

Guidance

Keystone correction
Enter the System Settings – Image Settings – Keystone Correction page to make manual adjustments.
Projection size
The optimal projection screen size of this series is 60 inches, the compatible size is 30-100 inches, and the corresponding distance from the wall/screen is 0cm-50cm. Choose the appropriate screen size and corresponding placement according to the actual use conditions.

Screen projection/ on-screen settings

• Screen projection: Make sure that the projector and the device to be projected (mobile phone, tablet, laptop, etc.) are connected under the same WiFi, click the screen projection function on the software of the device to be cast, and select “M1-XXXX” to cast the content to the projector.
• Same screen: Make sure that the projector and the device (mobile phone, tablet, laptop, etc.) are connected to the same WiFi.
• iOS system: Open “Application>EShare APP” on the projector, click screen mirroring in the toolbar of the device to be projected (mobile phone, tablet, laptop, etc.), and select “M1-XXXX” to start the same screen; Android system: The projector opens the “Application >EShare APP”, scans the QR code on the projection screen with the device to be on the same screen (mobile phone, tablet, laptop, etc.) and downloads and installs the EShare APP, selects “M1-XXXX” in the successfully installed EShare APP and connects, and clicks the wireless screen transmission to start the same screen.

The machine is on/off

• After the power is turned on, press the switch button of the fuselage or remote control to turn on;
• If the battery module is used and the power is not turned on, press and hold the body power on and off button for 5 seconds to turn on and off. At this time, the remote control is not supported to boot.

the system

• In the power on state, briefly press the switch button of the fuselage or remote control, and do not click “cancel” within 15 seconds, you can turn off the machine;
• In the power-on state, press and hold the fuselage power on and off button for about 10 seconds to force the shutdown.

Remote control pairing

• In the power on state, the remote control is close to the machine for 3-5CM, and press and hold the confirmation button and return button of the remote control for 5 seconds at the same time to complete the pairing;
• Depending on the version, new machines and new remote controls may need to be paired, and the pairing process is about 3~5 seconds.

System upgrade

• View the current version status of the system in System Settings – System Upgrade. If the current version is the latest version, you will be prompted; If a newer version is available, you will be prompted to upgrade. Do not lose power during the upgrade.

Network settings

• Select “Settings – Wireless Network” on the home page to enter the interface; Select “Wi-Fi” and enter the wireless network password to connect.

Audio Bluetooth output
Use the remote control to enter Settings – Bluetooth Settings. After turning on the Bluetooth of this machine, scan and search for nearby Bluetooth devices that have been turned on Support Bluetooth Speakers, Headphones, etc.. Once connected, audio can be output via an external Bluetooth device.

Play the media resource
Insert a USB flash drive through the USB interface, or connect to a computer TV and other devices through the HDMI interface, play video recordings, etc. During playback, you can pause/play audio and video through the remote control, or adjust playback speed, screen and other settings.

http://weixin.qq.com/r/9xHYwDbEX2sgrXKj90Tl
Consumer hotline：400-6161880
Official website www.witseer.com
Manufacturer: ONGINE TECHNOLOGY LIMITED
Address: No. 2, Hangtian South Road,
Longquanyi District, Chengdu, Sichuan

References

• 超短焦-慧示超短焦投影仪 - 慧示「WITSEER」投影仪官网

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>