tuya F4-5MP Security Camera User Manual

: June 9, 2024
: Tuya

Table of Contents

tuya F4-5MP Security Camera
Product Introduction
Component Description
install app
APP Video Browsing Details
Matters Need Attention
Read User Manual Online (PDF format)
Download This Manual (PDF format)

tuya F4-5MP Security Camera

Thank you for using smart camera

Product Introduction

Packing list: Smart Camera x 1, Manual x 1, USB Power Cord x 1, Power Adapter x 1,Screw Accessories Package x 4

Basic Parameters

Product Name: Smart Camera
Pixel: 1. 0Mp/2. 0MP
Video Compression: H. 264 High Profile
Image Enhancement: Digital Wide Dynamic 3D Noise Reduction Local Storage: MicroTF card
Wireless Encryption: WEP/WPA/WPA2 Encryption
Power Input: 5V 1A(Min)
Total Power Consumplion: SW (Max)
WirelessStandard: 2. 4G 802. 11 b/g/n
Support Plalform: Android/iOS

Component Description

Reset Bu1ton: Long press “reser hole 5sec, reset success.
It is recommended to insert 8-64GB high-speed Micro TF card, otherwise it will not be able to store, view historical video and support Important functions such as firmware upgrading.

install app

Download APP: scan the QR code below to download and install. Register and login: open the ” TuyaSmart ” APP to register and login according to the prompts.

Add The Device-Scan QR code mode

Make sure Wi-Fi is available and connected to the internet.
Connect the camera to the power, then the system startup is completed.
Open the “TuyaSmart” APP, press the’+’ In Ille upper right comer or the main screen (Figure 01); choose “Security & Sensor”, click “Smart Camera” (Figure 02) to add the camera; and then dick “Next step” (Figure 03);
If the mobile phone is not connected to wi-fi, please click “Connect to Wi-fi” (Figure 04);
It will jump to the WLAN interface and connects Wi-Fi (Figure 05). Please note that only 2. 4 GH Wi-Fi network is supported;
If the phone is connected to Wi-F’i (F’igure 06);
click “Conflrm”. It will jump to the interface to prompt to scan the QR code with camera and click “Continue” (Figure. 07);
A QR code will prompt on your screen and you need to scan it with the Smart Camera. (the camera is about 20-30 cm away from the mobile phone lens). Then click “hear the prompt sound’ (Figure. 08).
“connecting” (Figure. 09);
When the progress reaches 100%,conneclion completed(Figure 10), and click “Finish”;
Then jump to preview interface (Figure 11)
After closing the device preview interface, the interface returns to the APP home page. At this time, the connected device will appear on the APP home page (Figure 12). Then you can click directly to the device interface to see the monitoring situation without re-adding afterward.

Add The Device-AP Mode

If you want to use /lP Mode,press the resel button on the machine

Make sure Wi-Fi is available and connected to the Internet.
Connect the camera to the power, system startup completed.
Open “TuyaSmart” APP, press the’+’ in the upper light earner or the main screen (Figure 13); choose ·securlly & Sensor\ click “Smart Camera• (Figure 14) to add camera ; Alternatively, choose “other ways” to add (as shown in Figure 15);

Note : Before using the “‘AP Mode·,you need to switch to “AP Mode” by lightly pressing the “Reset key” or the device.

Then click “hot spot configuration” {Figure 16;
Then click” compatibility mode”, clicks”Next” (Figure 17);
Then click “change Network” (Figure 18);
Then enter the password to complete the connection (Figure 19);
Click Back and return to the APP compatible mode interface, where the Wi-Fi name and the connected Wi-Fi name are displayed Password, click the “Confirm” button {Figure 20);
The page jumps to where the interface prompts “Wi-fi” to connect to Ille device hotspot and clicks ·connect· (Figure 21)
The interface jumps to the WALN connection interface, finds the Wi-Fi at the beginning of “Smart Lifi”. and clicks on the connection (Figure 22);
When the connection is completed, click back and return to the APP interface, at which time the APP display device is conneded (Figure 23).
At lhis time, the device has been successfully connected; the interface jumps to “Add Device Successful” (Figure 24);
Then click “connected”, it will jump to lhe Preview Interface of the Device (Figure 25)
Close the device preview interface and the interface returns to the APP home page, at which point the connected device will appear on the APP home page.(Fig. 26), After entering the device interface to view, no need to re-add, click directly into the device interface to view.

APP Video Browsing Details

Preview mode
Monitor Switch
About device
SQ
Full screen

Matters Need Attention

Try to keep away from metal space; Avoid furniture, and microwave ovens blocked; Avoid the space where the audio, video and data lines are wound, and keep the space away from them as large as possible; Ensure that as close as possible to the coverage or wireless Wi-Fi signals. Switching network environment; In the new network environment, please press the reset hole for about 5 seconds, then connect to lhe network.

The name and content of the harmful substances in the product

This product conforms to RoHS environmental protection requirements. Al present, there is no mature lechnology in the world to replace or reduce the lead content in lhe electronic ceramics. porcelain, optical glass, steel and copper alloy.