DISTINQ DQMF03BK Milk Frother Instruction Manual

DISTINQ DQMF03BK Milk Frother

instruction manual
model: DQMF03BK
super lekker

Device Overview

1. Lid
2. Stirring insert
3. Frothing insert
4. Milk jug
5. Button with indicator LEDs
6. Socket with cable winding
7. Power cord with plug (not shown)
8. Handle
9. MIN marking
10. MAX marking (during foaming)

Important Safety Information

• This product can be used by children aged 8 and used when supervised or regarding the safe use of the product and the resulting understand dangers.
• Children must not play with the product.
• Cleaning and maintenance by the user may not carried out by children, unless they are eight years old or older and are supervised.
• The product and its connection cable are from children under eight years.
• This product can be used by persons with reduced physical, sensory or mental abilities; or lack of experience and/or knowledge are used, if it is supervised or use of the product and the the risks resulting from this.
• A damaged power cord must only be supplied by the manufacturer, a workshop commissioned by him or a similar to be replaced by a qualified person.
• Use the product only for intended use and with the recommended accessories and components. A improper or incorrect use is dangerous.
• Attention! Do not use any liquid on the device connector overrun.
• Note: After application, the surface of the heating elements over residual heat.
• Be careful! In order to avoid an unintended resetting the protective temperature limiter to the product must not be switching device such as a timer supplied or connected to a circuit which is regularly introduced and is switched off.
• This product is not for commercial use suitable. It is only for use in the house-hold and similar applications, such as: -in kitchens for employees in shops, offices and others industrial sectors,
• Do not fill milk above the upper limit. Hot milk can squirt out.
• Warning! Never open the lid while the milk boils.
• Use the product only with the supplied base.
• Do not put the product in water for cleaning to be immersed.
• Clean the product and other accessories after each use. Note the chapter cleaning and care.

Intended Use

The product is only suitable for heating/frothing milk and making hot chocolate drink. Any other use may cause damage to the device or injury.

Before First Use

1. Place the base on a dry, level and stable base.
2. Unwind the power cord from the cable winding in the base until the the desired length. Insert the cable into the intended recess at the base (Fig. 1).
3. Connect the power plug to a suitable socket.
4. Clean the milk frother before first use to remove production residues.
5. Fill the milk frother with cold water up to MAX mark and let the water heat once. Then throw it away. Repeat the procedure and always allow the product to cool down in between. The product is now ready for operation.

Warning: Do not immerse the milk frother in water.
Make sure that the connection at the bottom of the milk frother stays dry.

Operation

• Garde A – Roeren
• Garde B – Schuimen en roeren

1. Operating Mode 1: Firm, Warm Froth
   Choose this mode to create a warm milky froth with a firm consistency. The RED operating indicator lights up.

2. Operating Mode 2: Creamy, Warm Froth
   Choose this mode to create a warm, creamy, easy to pour milk froth. The RED operating indicator lights up.

3. Operating Mode 3: Heat with light froth
   Choose this mode to create a warm milk or hot chocolate drink. The WHITE opera-ting indicator lights up.

4. Operating Mode 4: Cold froth
   Choose this mode to create a cold milky froth ( room temperature froth). The BLUE operating indicator lights up.

• The red/ blue/ white LED display will flash and your whisk will begin to turn after approximately three seconds.
• The frother will stop automatically as soon as the milk is ready. The red/ blue/ white LED display will flash for a few seconds and then turn off.
• You can stop the frothing process at any time by pressing the On/Of button.
• Wait 30 seconds before removing the canister to allow milk to settle.
• Wait a few minutes before using the frother again.
• When you use operating mode 1, 2 & 4, the milk yield must be between the MAX and MIN marking (Fig. 2) and must not contain 130 ml above.
• When you use operating mode 3, the milk yield must be between the MAX and MIN marking (Fig. 3) and must not exceed 240 ml.

Note
If you make more hot milk froth or more hot milk, the milk frother must cool for a few minutes before you use it again. As long as the milk frother is hot, a built-in thermostat to prevent the product from operating. You can rinse the inside of the milk frother with cold water so that it cools down faster.

Dry Walking Protection

• If there is not enough milk in the milk frother, switch the product is automatically removed. Nevertheless, always make sure that: there is enough milk in the container, because the automatic shutdown life of your product shortened.
• Allow the product to cool before refilling milk.
• Disconnect the power plug and leave the device before cleaning cool completely.
• Never immerse the appliance or base in water during cleaning or other liquids. Never keep it under running water.
• Clean the external surfaces of the device with a slightly moistened wipe and then dry thoroughly.
• Make sure that no water enters the appliance interior (at the switch) and on the socket reached.
• Do not use solvents or abrasives for cleaning, hard brushes, metallic or sharp objects. Solvents are: harmful to health and attack the plastic parts; abrasive cleaners; and aids scratch the surface.
• After use immediately clean the lid, inserts and milk frother with hot water.

Technical Data

• Power supply: 220-240 V~, 50 Hz
• Power consumption: 350-450 W
• Capacity: MIN: 75ml
• MAX: 130 ml
• MAX: 240 ml
• Protection class: I

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>