AT T Uplink 5500M Universal Dual Sim Alarm Communicator Verizon Instruction Manual

: June 9, 2024
: AT&T

Table of Contents

LED Indicator
Adding preferred monitoring station
Uplink end-user app credentials
Remote Arming/Disarming via Keyswitch (Optional)
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

**AT T Uplink 5500M Universal Dual Sim Alarm Communicator Verizon Instruction Manual

**

WARNING

The wiring should be done only when the panel and the communicator are disconnected from the power line!

Connect the antenna and place it outside of the alarm panel’s box.
Connect + and – of the communicator to a max of 12V – 29V DC power supply.

LED Indicator

(+)	12-29 VDC Power Supply
(-)	Ground
IN1	Digital Input 1 (pull-up to VDC)
IN2	Digital Input 2 (pull-up to VDC)
IN3	Digital Input 3 (pull-up to VDC)
IN4	Digital Input 4 (pull-up to VDC)
OUT1	Latched/Pulse Output (transistor, open collector, 100mA)
OUT2	Pulse Output (transistor, open collector, 100mA)

LED in dicator

Slow flashing – trying to establish connection
Constantly On – connection established at good signal level
Constantly On, blinking every 5 sec. – connection established at low signal level
Fast flashing – sending cellular traffic

Default configuration of the digital inputs and outputs

IN1	General Alarm – Zone 251	OUT1 Preconfigured as Pulse Output
IN2	General Alarm – Zone 252	OUT2 Preconfigured as Pulse Output
IN3	General Alarm – Zone 253
IN4	General Alarm – Zone 254

The inputs are tripped by applying a negative (GND) signal and must share the same common ground.
All inputs can be connected to bell output and will recognize a pulsed voltage
as Fire Alarm and steady voltage as General Alarm. Always use the active
output of the bell and wire it to the alarm panel according to the bell supervision
requirements – refer to the alarm panel installation manual.

Changing the configuration of the digital inputs and outputs (Optional) Note: The device should be powered up and connected to the network.

Changing the configuration from the Uplink Dealers Portal:

Open the “Device Dashboard” and navigate to “Advanced Settings”
Check the “Enable Online Settings” checkbox and press “Get Current Settings”
Change the settings of the digital inputs and outputs under the “Pins” section Changing the configuration from the RControl Admin App:
Go to the “Settings” tab and navigate to “Advanced Settings”
Enable “Editing”
Change the settings of the digital inputs under the “Inputs” section

Register your company at www.uplinkdealers.com or use your existing account to login.

Adding preferred monitoring station

Contact your monitoring station and request your Uplink Dealer Code.

Specify your preferred monitoring station during your initial registration in the list found in section “Additional Information” > “Preferred Monitoring Station.” Provide your Dealer code in the corresponding field, OR
Add preferred monitoring station/s after registration from My Devices > Monitoring Stations > Add CMS.

Add a new device and choose cellular service monthly billing method

Use the device Serial Number and the Config Key provided with this manual.

Go to My Devices > Devices > Add New Device.
Select monitoring station (optional)
Select preferred cellular service monthly billing method.
From Monitoring Station – You will be billed for cellular service by the monitoring station.
From Uplink – You will be billed for cellular service by Uplink.

Uplink end-user app credentials

Download the Uplink mobile application on your Android or iOS device by scanning the QR codes.

Remote Arming/Disarming via Keyswitch (Optional)

Configure one of the outputs of the unit as a Keyswitch from “Advanced Settings” menu.
Configure a zone on the panel as a momentary keyswitch (refer to the panel’s installation manual).
Configure a PGM output of the panel to activate (switch to ground), when the panel is armed, and to deactivate, when disarmed (refer to the panel’s installation manual).
Wire the device to the panel according to the Key switch wiring diagram below.