AT T F5688A 5G Gateway Instructions

AT T F5688A 5G Gateway Instructions

5G GATEWAY BGW530-900 SAFETY AND REGULATORY INFORMATION

SAFETY GUIDELINES

ALWAYS READ THE AT&T 5G GATEWAY QUICK START GUIDE BEFORE SET UP OR USE OF THE FAST 5688A PRODUCT. IT IS YOUR RESPONSIBILITY TO FAMILIARIZE YOURSELF WITH THE PRODUCT USER GUIDES AND WARNINGS, AND TO USE THE PRODUCT PROPERLY.

Installation and Safe Usage Instructions:

1. Place the Gateway in a vertical orientation on a flat
2. To improve reception, place the equipment near a window, but avoid placing it in direct
3. Connect the manufacturer supplied AC to DC power The FAST 5688A Gateway requires the use of a 12VDC, 3.5A Jack power adapter. Only use a manufacturer supplied and approved power adapter.
4. Connect the “FAST 5688A” to the AC Mains in accordance with the installation instructions in the Quick Start Guide, and the markings on the identification label (voltage, current, and frequency of electricity network).
5. Connect one Ethernet cable (not provided) to the RJ45 yellow port on one end and to the Internet access of your device (laptop or computer). Repeat as necessary with the other available Ethernet port.

When using this device, basic safety precautions should always be

followed to reduce the risk of fire, electric shock, and injury to persons including the following:

1. Do not use this product near water and avoid contact with For example, do not use near a bathtub, wash bowl, kitchen sink, laundry tub, in a wet basement, or near a swimming pool. Care should be taken so that liquids are not spilled on this equipment.
2. This equipment is for indoor use only, do not place or install in an outdoor
3. Place the equipment on a firm, solid surface, at least 31 cm away from any other If you place the equipment on something unsteady, the equipment may fall and be damaged. If you place the equipment on a soft surface, such as a rug, sofa, or cushion, the vents on the equipment may be blocked, causing the equipment to overheat.
4. Never insert objects into the vents of this equipment as this can result in the risk of electrical shock or
5. As the power adapter is the only way to connect to the electrical network, the product must be installed near an easily accessed power
6. This equipment should only be operated with the type of power supply (Voltage and Current) indicated on the marking label, the one provided with the Gateway. The socket-outlet should be easily accessible.
7. Do not overload wall outlets or extension Doing so can result in the risk of fire or electrical shock.
8. Avoid blocking any vent openings or exhaust exits on this Do not place equipment in a built-in installation such as a cabinet that may impede the flow of air through the ventilation openings. Do not place anything on top of the product.
9. The equipment should be situated away from heat sources such as radiators, heat registers, stoves, or other heat producing appliances and
10. Care should be taken to ensure that the power cord is routed, so it is not likely to be walked on or pinched by items placed upon or next to Check the power cords regularly. If you find any damage, replace the power supply immediately.
11. Unplug this equipment before Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning only.
12. This equipment is not user serviceable and is to be serviced by qualified personnel Do not disassemble this equipment. If service is required, disconnect all power from the equipment and consult qualified service personnel.
13. To disconnect this equipment from AC power, unplug the power supply from the AC wall
14. Use the product in the environment specified as below:
    • Air temperature between 0°C (32 F) and +41.7°C (107 F).
    • Relative humidity between 20% and 90%.
    • Altitude: 2743 meters (9000 feet)

Federal Communications Commission (FCC) Statements

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

• This device may not cause harmful interference, and
• This device must accept any interference received, including interference that may cause undesired

Modifications:

You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment.
FCC Responsible Party:            Sagemcom USA
14651 N. Dallas Parkway Suite 900
Dallas, TX 75254
Phone: 972-674-4100
FCC ID: VW3F5688A

Radio Frequency Interference Statement

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

1. Reorient or relocate the receiving
2. Increase the separation between the equipment and
3. Connect the equipment into an outlet on a circuit different from that to which the receiver is
4. Consult the dealer or an experienced radio/TV technician for

FCC Radiation Exposure Statement

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
This device produces radio frequency energy in the 600 MHz, 700 MHz, 800 MHz, 1.7 GHz, 1.8 GHZ, 2.4GHz and 5GHz spectrum. The antenna must be positioned to keep a minimum distance of 51 cm from the radiating element to any nearby person.
FCC regulations restrict the operation of this device to indoor use only.
For further compliance information in this regard, including FCC Guidelines for Human Exposure and FCC Information for User, please consult: https://www.att.com/legal/terms.openinternetpolicy.html
Issued by Sagemcom Broadband SAS Sagemcom
250, route de l’Empereur – 92500 RUEIL MALMAISON FRANCE
© Sagemcom Broadband SAS 2023
All rights reserved. Subject to availability. Rights of modifications reserved. www.sagemcom.com

Read More About This Manual & Download PDF:

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>