ROCKVILLE RWM120X Series High Performance Wireless Microphone System Owner’s Manual

ROCKVILLE RWM120X Series High Performance Wireless Microphone System

Missing items? lt you ordered a bundle that includes more than one product and you are missing part of your bundle then it just means your order shipped from two different Warehouses. YOu will receive the remaining tems very soon. If you have any concems or inquiries, feel free to call our customer support center at 1-646-758-0144, 24 hours a day/7 days a week.

Thank you for purchasing this Rockville Wireless Microphone System. Please read this installation guide carefully for proper use of your Rockville Wireless Microphone System. Should you need assistance, please call our technical help line at 1-646-758-0144, 24 hours a day/7 days a week.

UNPACKING

Specs

FEATURES

• High performance wireless microphone system
• Includes transmitter with either (2) handheld, (2) lavaliere, or (2) headset microphones
• High-sensitivity, unidirectional, wireless cardioid microphones
• Featuring a dual filter design to limit feedback and interference
• Transmitter automatically links to receiver for ease of use
• Durable composite microphone construction
• Comfortable ergonomic design

SPECIFICATIONS

SYSTEM

• Operating Range: 100-200 (indoor), 65-165 (outdoor)
• Audio Frequency Response: 80-12000Hz
• Dynamic Range: 280dB
• Signal-to-Noise Ratio: 280dB
• Operating Temperature: 41°F-113°F
• Carrier Frequency Range: 180-280MHz

RECEIVER

• Sensitivity: (S/N=30dB) >2mV
• De-Emphasis: 50uS
• Audio Output Impedance: 6002
• Audio Output Level.: 0-0.5V
• Power Supply: AC110V /50Hz
• Current Consumption: s50mA
• Audio Out Connector: 1/4″ unbalanced

TRANSMITTER

• Frequency Stability: +0.005%
• RF Output Power: s30mW
• Modulation Mode: VHF
• Maximum Deviation Range: +50KHz
• Microphone Mode: Fixed
• Pre-Emphasis: 50uS
• Power Supply: 9V Batt./1.5Vx2
• Current Consumption: s35mA

Receiver

(Front)

• a. Antenna
• b. Power on/off switch
• c. Volume adjustment knob
• d. LED channel indicator
• e. LED power indicator

(Back)

• a. Antenna port
• b. Audio out (1/4″ TRS connection)
• c. Power plug

Microphones

• a. Microphone windscreen
• b. Power LED indicator
• c. Power on/off switch
• d. Battery compartment
• e. Clip
• f. Connector jack
• g. Microphone frequency sticker location

Body Pack

• a. Microphone input

• b. Battery compartment

• c. Microphone windscreen

• d. Gain control

• e. LED power indicator
  When ON the LED power indicator will be on. When the unit reaches 10% power or less, the LED will begin to flicker until it turns off

• f. ON/OFF switch
  When the switch is in the middle position, the microphone will be on MUTE/ STANDBY

Setup and Operation

• The receiver should be placed in an area that is stable and least likely to shake the unit.
• The receiver should be at least 3′ off the ground for optimal transmission.
• Connect the antenna, balanced cable AF line, and power supply provided.
• The antenna should extend vertically.
• Switch on the receiver.
• While the receiver is in standby, switch on the microphones.
• Adjust volume as necessary.
• Use trim adjustment on the body pack to fine-tune the mic gain so that the audio output is louder (MAX) or softer (MIN)

Tip:
To minimize feedback avoid operatinng the microphones in close proximity of or in front of speakers.

Frequency Groups

• GROUP A: 215.20 MHz, 183.60 MHz
• GROUP B: 212.10 MHz, 185.15 MHz
• GROUPC: 206.35 MHz, 179.30 MHz
• GROUP D: 203.40 MHz, 174.10 MHz
• GROUP E: 202.10 MHz, 174.80 MHz

Troubleshooting

Visit us at:
RockvilleAudio.com

©2022 ROCKVILLE// The information presented is subject to change and/or improvement without notice.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>