ROCKVILLE RockPAR50 LED RGB Compact Par Owner’s Manual

ROCKVILLE RockPAR50 LED RGB Compact Par Owner's Manual

Who reads manuals?
Scan the QR code or go to the URL to access how-to video(s), the owner’s manual, and other important information you may need to get the most out of your item.

If you prefer written instructions, please read ahead!

With Rockville you get many options.

rockvillesupport.com/rockpar50

rockvillesupport.com/rockpar50-wht

Missing items? If you ordered a bundle that includes more than one product and you are missing part of your bundle then it just means your order shipped from two different warehouses. You will receive the remaining items very soon. If you have any concerns or inquiries, feel free to call our customer support center at 1-646-758-0144, 24 hours a day/7 days a week.

Thank you for purchasing this Rockville RockPAR50 Compact RGB LED Par Can Wash Light. Please read this guide carefully for proper use of your RockPAR50. Should you need assistance, please call our technical help line at 1-646-758-0144, 24 hours a day/7 days a week.

INCLUDES

• Par Light
• Power Cable
• Dual-Bracket
• Owner’s Manual
• Warranty Card

IMPORTANT SAFETY INSTRUCTIONS

NO USER SERVICEABLE PARTS INSIDE. WE RECOMMEND TAKING THE UNIT TO A QUALIFIED SERVICE TECHNICIAN FOR ANY REPAIRS.

• To reduce risk of electric shock, never open the There are no user serviceable parts, refer service to an authorized Rockville service center.

• Avoid looking directly into the

• Do not expose this unit to any kind of

• The products housing may become hot during Do not touch.

• Please ensure that the unit is situated in a properly ventilated area. Allow at least 20 inches between this device and a wall.

• This device has an IP20 rating and is intended for indoor use

• Do not operate this unit when the cover is

• Do not attempt to operate this unit if the power cord has been frayed or

• Do not attempt to break off or remove the ground prong. This prong is used to reduce the risk of electrical shock and fire in case of an internal short.

• Never plug this unit into a dimmer

• Do not operate this unit if it is

• This unit is intended for indoor use

• During long periods of non-use, disconnect the unit from power

• Always mount this unit in a safe and stable

• Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to the point of exit from the unit.

• To avoid unnecessary wear and to improve the unit’s lifespan, unplug the unit when not in use for extended periods of time.

• Assembly and installation of the device must be carried out by a specialist familiar with the hazards and the relevant regulations. Maintenance, operation and commissioning of this device must only be carried out by qualified persons.

• When choosing a location for your device, make sure to avoid impact, vibration, dust, hot and cold temperatures and dampness. Furthermore, no powerful transformers or motors must be used close to the device.

• The effect light must only be operated at a maximum ambient temperature of 40°

• Never cover the device. Make sure when mounting with other equipment that there is sufficient ventilation. Maintain a sufficient distance to other devices and walls. Never in stall the effect light in direct proximity of heat sources. Do not point any strong spot lights or light sources towards the device. This may cause overheating (danger of fire!).

• Do not drill or screw additional screws into the casing in order to fasten the device. This may expose dangerous voltage to touch.

• The device must be mounted out of normal

• Illuminated objects must be at least 0.5m away from the device’s light emission source. Easily flammable materials such as decorative fabrics must also have a distance of at least 0.5m to the device. Otherwise, such objects may catch fire!

• When mounting the product, make sure that the power cord is neither jammed nor damaged by sharp edges.

• During installation or service work, the area below the place of installation must be cordoned off.

• The installation surface or mounting fixture needs to be designed in a way that it can take ten times its load capacity for at least one hour without permanent damaging

• It is also essential that the device is secured by means of a second safety restraint that is independent of the actual mounting supports when installing it in an elevated position. No part of the installation must fall down if the main suspension system fails.

• Observe all relevant regulations of your country when installing theAcceptance test (in case of industrial/public use):

• Before first use and after any significant modifications, the installation (including the electrical connections) must be inspected by an official expert.

• A yearly inspection by an expert is

• At least every four years, an acceptance test must be carried out by an

• If you want to mount the device on a suitable traverse system, attach the effect light with the mounting bracket and a suitable traverse clamp that is available separately.

• For this, install the effect light with the assembly bore of the mounting bracket to the traverse clamp and that in turn to the traverse system. Use only assembly material suitable for the type of assembly and for bearing the effect light load.

• The assembly must never swing

• Additionally secure the installation with a suitable safety restraint cable or a safety

• The safety retention rope or the net must be designed to support the effect light in the event of failure of the main support system independently of the main attachment.

Functions

1. OMX out
2. Rubber feet
3. LCD display
4. OMX in
5. Power linking socket (power out)
6. Mic
7. IEC AC power socket with user-serviceable fuse
8. Controls:
   Mode: Press repeatedly to see mode
   Up: Scroll up through settings.
   Down: Scroll down through settings.
   Enter: Use to make selection.

Operation

DMX

To set the DMX starting channel address press the mode button until you see “d­,, Now use the UP and DOWN buttons to select the desired setting. Press enter button to save your selection. Internal Programs To select and run one of the four built-in programs press the mode key until the desired program is found.

DMX Termination

The last fixture of a DMX chain has to be “terminated”. This prevents electrical noise from disturbing and corrupting the DMX control signals. To terminate the last fixture solder a¼ Watt, 120 ohm resistor across the DATA – and DATA + wires. The connections are illustrated below. If you are only connecting a few fixtures which are close together and use a short run to the controller, you maybe able to operate without a terminator.

Modes

DMX Channel Values and Functions

3 Channel Mode: a001 – a512

6 Channel Mode: d001 – d512

Maintenance and Cleaning

Always observe the following safety instructions before cleaning or servicing the effect light:

• Live components may be exposed if covers are opened or components are removed.
• The device must be disconnected from all power sources before any servicing or repair work is carried out.
• Capacitors inside the device may still carry voltage even though they have been discon­ nected from all power sources.
• Only qualified experts familiar with the hazards involved and the relevant regulations must perform repairs.
• Never use any aggressive cleaning agents, cleaning alcohol or other chemical solutions, since these may damage the casing or even impair function.
• Always disconnect the product from the power supply before cleaning it.
• Use a dry, lint-free cloth for cleaning the product.

Handling

• Never connect the mains plug to a mains socket immediately after the device has been taken from a cold to a warm The resulting condensation may destroy the device.
• Allow the device to reach room temperature before connecting Wait until the condensation has evaporated.
• Never pull the mains plug from the mains socket by the Only pull it from the mains socket by the intended grip areas.
• Unplug the mains plug from the mains socket if you are not using the device for an extended period of time.
• Disconnect the mains plug from the mains socket during thunderstonns for reasons of
• Never put any filter foils, masks or other materials over the light exit. This may cause heat damage and danger of fire.
• The device may heat up during Never touch the casing during operation. Let the effect light cool off after operation before touching or cleaning the casing.
• Do not cover the device to ensure sufficient ventilation. Air circulation also must not be impaired by any objects like magazines, tablecloths, curtains, etc. During operation, keep a minimum distance of 0.5 meters around the device.
• The device is not suitable for continuous operation. Consistent compliance with operating breaks increases the operational life span of the Let the device cool off for an extended period before taking it into operation again.

Features and Specifications

• Rockville RockPAR50 Compact RGB LED Par Can Wash Light
• Power input and power output for linking multiple units using only one wall outlet
• DMX in and out allows daisy chaining multiple lights making it easy to control numerous lights synced together
• Three or six channels of DMX control
• Operation Modes: Auto, Voice activated, Master-Slave, DMX512
• Strobe, color change, color fade, dimmer, ID address, color mixing controls
• Colors: 7 million different color change variations
• Double-bracket serves as floor stand and hanging bracket
• Static colors and RGB color mixing with or without DMX controller
• Strobe effect with adjustable speed
• Built-in automated programs via master/slave or DMX with variable speed
• Slim profile with powerful and long lasting LEDs
• Beam angle: 15°, 25°, 35°, and 45°
• Light source: Eighteen high power 1 watt LEDs (six red, six green, and six blue)
• Dimmer: 0 – 100%
• Input Voltage: 110 – 240V, 50/60Hz
• Power Consumption: 24W
• Advanced switching power supply
• Constant current keeps LEDs from blowing
• 20,000 – 100,000 hour LED life
• IP grade: 20
• 110/220 switchable
• Unit dimensions: 01″ x 4.33″
• Unit weight: 43Lbs

Troubleshooting

RockvilleAudio.com

©2022 ROCKVILLE// Features and specifications are subject to change and/or improvement without notice.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>