Orbic Q10 Smartphone User Guide

Orbic Q10 Smartphone

Applicant Information

Applicant : Reliance Communications LLC
Applicant Address : 91 Colin Drive, Unit 1, HOLBROOK, New York 11741, United States
Manufacturer : N/A
Manufacturer Address : N/A

General Information

telecommunications equipment）
Product Photo
|

Result of Preparing for Re-Use/Recycling/Recovery

A

B adapter

Reuse/Recycling/Recovery Targets under

the 2012/19/EU WEEE Directive

| 55| 75
Result of Assessment| 89.90| 89.90
WEEE Requirement Compliance| Yes| Yes

C data line

Reuse/Recycling/Recovery Targets under

the 2012/19/EU WEEE Directive

| 55| 75
Result of Assessment| 91.75| 91.75
WEEE Requirement Compliance| Yes| Yes

Appearance of the Product

|
---|---
|

Selective Treatment for Materials and Components

According to Articles 8(2) and the Annex of the WEEE Directive, this product contains components and material items are described in the following table.

Component/Material| Photo No.| Size| Quantity| Weight (g)
---|---|---|---|---
Printed circuit boards of mobile phones generally, and of other devices if the surface of the printed circuit board is greater than 10 square centimeters| A-5| 6.46cm5.24cm| 1| 9.37
| B-3| 3.42cm3.29cm| 1| 15.85
Battery| A-4| /| 1| 49.07
liquid crystal displays (together with their casing where appropriate) of a surface greater than 100 square Centimeters and all those back lighted with gas discharge lamps| A-3| 15.66cm*6.95cm| 1| 43.67

Disassembly Tree

Disassembly Procedure

The disassembly procedure taken here is in accordance with the treatment requirements under the Annex of the WEEE Directive. In addition, to consider economic and efficiency factors, manual operation and disassembly tools have been applied to separate the components and materials from this product in order to simulate the scenario at the treatment facility, and to achieve the objective that the separated components and materials can be reused, recycled and recovered.

Connection Technique

For this product, the connection technology including as following：
Screw： 18
Glue： 14
Pressing Fits： 5

Disassembly Tool

Cross screwdriver

|

Disassembly Time

35 Minutes 30 Seconds

Loss During Disassembly

A
Product weight before disassembly： 181.12g
Product weight after disassembly： 181.01g
Lost rate： 0.06%
B adapter
Product weight before disassembly： 30.64g
Product weight after disassembly： 30.62g
Lost rate： 0.07%
C data line
Product weight before disassembly： 21.31g
Product weight after disassembly： 21.27g
Lost rate： 0.19%

Material and Recycling Information

According to the information declared by the applicant company, the material and recycling information for this product is described in the following table.
The reuse, recycling and recovery assessment for this product is based upon economic and efficiency considerations, and the waste treatment technologies and equipment that are most frequently available to the market.

A

Photo No.| Component/Material Composition| Weight(g)| Percent Weight(%)| Reuse/Recycling Rate (%)| Energy Recovery (%)| Recovery Rate (%)
---|---|---|---|---|---|---
A-1| Plastic parts| 29.24| 22.14| 19.49| 0.00| 19.49
A-2| Metal parts| 42.81| 32.42| 31.77| 0.00| 31.77
A-3| LCD| 43.67| 33.07| 30.43| 0.00| 30.43
A-4| Battery| 49.07| /| /| /| /
A-5| PCB| 9.37| 7.10| 6.39| 0.00| 6.39
A-6,A-7,A-8,

A-9

| Mixed| 6.85| 5.19| 4.67| 0.00| 4.67
Total| 181.01| 99.92| 92.75| 0.00| 92.75

B adapter

Photo No.| Component/Material Composition| Weight(g)| Percent Weight(%)| Reuse/Recycling Rate (%)| Energy Recovery (%)| Recovery Rate (%)
---|---|---|---|---|---|---
B-1| Plastic parts| 11.95| 39.00| 34.32| 0.00| 34.32
B-2| Metal parts| 2.82| 9.20| 9.02| 0.00| 9.02
B-3| PCB| 15.85| 51.73| 46.56| 0.00| 46.56
Total| 30.62| 99.93| 89.90| 0.00| 89.90

C data line

Photo No.| Component/Material Composition| Weight(g)| Percent Weight(%)| Reuse/Recycling Rate (%)| Energy Recovery (%)| Recovery Rate (%)
---|---|---|---|---|---|---
C-1| Plastic parts| 4.29| 20.13| 17.72| 0.00| 17.72
C-2| Metal parts| 2.55| 11.97| 11.73| 0.00| 11.73
C-3| Cable| 14.43| 67.71| 62.30| 0.00| 62.30
Total| 21.27| 99.81| 91.75| 0.00| 91.75

Note:

• Due to their insignificant weight and the difficulty of their separation in a manual operation, sticker, solder, paint and printing materials are not included in this assessment.
• Plastic containing brominated flame retardants is not assessed in the list.
• Battery subject to 2006/66/EC Directive, it must be removed from the WEEE for recycling separately, the weight percent, reuse & recycling rate, recovery rate do not contain the battery.

Recycling and Recovery Rate Calculation

Total weight of the product is including the main product and accessories.

ANNEX of WEEE Directive

Selective treatment for materials and components of waste electrical and electronic equipment:

• Polychlorinated biphenyls (PCB) containing capacitors in accordance with Council Directive 96/59/EC of 16 September1996 on the disposal of polychlorinated biphenyls and polychlorinated terphenyls (PCB/PCT) ,
• Mercury containing components, such as switches or backlighting lamps, Batteries,
• Printed circuit boards of mobile phones generally, and of other devices if the surface of the Printed circuit board is greater than 10 square centimetres,
• Toner cartridges, liquid and pasty, as well as colour toner,
• Plastic containing brominated flame retardants,
• Asbestos waste and components which contain asbestos,
• Cathode ray tubes,
• Chlorofluorocarbons(CFC), hydrochlorofluorocarbons (HCFC) or hydrofluorocarbons (HFC), hydrocarbons(HC),
• Gas discharge lamps,
• Liquid crystal displays (together with their casing where appropriate) of as surface greater than100 square centimeters and all those back-lighted with gas discharge lamps,
•  External electric cables.
• Components containing refractory ceramic fibres as described in Commission Directive 97/69/EC of 5 December 1997 adapting to technical progress Council Directive67/548/EEC relating to the classification, packaging and labeling of dangerous substances,
• Components containing radioactive substances with the exception of components that are below the exemption thresholds set in Article3 of and Annex I to Council Directive 96/29/EU of 13 May1996 laying down basic safety standards for the protection of the health of workers and the general public against the dangers arising from ionizing radiation,
• Electrolyte capacitors containing substances of concern (height >25 mm, diameter>25 mm or
  proportionately similar volume).

Recommendations for WEEE Directive Compliance

• In order to avoid the product not meeting the reuse/recycling/recovery targets regulated under the WEEE Directive and the regulations of EU countries, the applicant company should, when selecting material and components design, consider they can be easy to reuse and recycle. This consideration will lessen the impact of the required international environmental directives and also improve the product’s competitiveness.
• It is recommended that the applicant company, when designing new product, especially where components and materials have a large weight ratio, should consider using recyclable materials in order to increase the product’s reuse/recycling/recover ratio.
• The product should apply to the RoHS Directive (Directive2011/65/EU on the restriction of the use of certain hazardous substances in electrical and electronics equipment). The hazardous substance specification in the Directive should be controlled in the homogenous material of this product.
• If a product has changed its product design, or materials or components employed, then the product should be reassessed and retested in accordance with the WEEE Directive for reuse/recycling/recovery assessment and RoHS for restricted/banned substances requirements.

Annex A General Information

Identification of the Responsible Testing Laboratory

Road, Block 67, BaoAn District, Shenzhen, Guang Dong Province, P. R. China

Identification of the Responsible Testing Location

67, BaoAn District, Shenzhen , Guang Dong Province, P. R. China

WEEE REPORT

Applicant : Reliance Communications LLC
Product Name : Orbic Q10
Model Name : RC609L
Brand Name : Orbic
Test Request : As specified by client, to assess the reuse/recycle/recovery of the submitted sample under article 7 of Directive 2012/19/EU
Receipt Date : 2022-04-24
Test Date : 2022-04-25 to 2022-04-28
Issue Date : 2022-06-02
Conclusion : This report is true and effective and the results of the test meet
the requirements of WEEE, this product is qualified.

NOTE: This document is issued by Shenzhen Morlab Communications Technology Co., Ltd., the test report shall not be reproduced except in full without prior written permission of the company. The test results apply only to the particular sample(s) tested and to the specific tests carried out which is available on request for validation and information confirmed at our website

Tel: 86-755-36698555 Fax: 86-755-36698525
http://www.morlab.cn
E-mail : service@morlab.cn

References

• 摩尔实验室

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>