brennenstuhl WFD 3050 P WiFi LED Light with-without Motion Detector Instruction Manual
- June 9, 2024
- brennenstuhl
Table of Contents
WFD 3050 P WiFi LED Light with-without Motion Detector
Instruction Manual
WFD 3050 P WiFi LED Light with-without Motion Detector
| 
---|---
Attention: Please read these instructions for use carefully before using the lamp and keep them in a safe place!
SAFETY NOTE
-
Before each use, check the product for possible damage.
Never use the product if you notice any damage. In this case, contact a qualified electrician or the service address of the manufacturer.
Non-observance can result in danger to life due to electric shock! -
Installation and maintenance of the lamp must be carried out by a qualified professional.
-
Electrical installations may only be carried out in compliance with the safety regulations (VDE 0100 for Germany).
-
A VDE-certified connecting cable must be used for connection.
-
The lamp must be properly grounded (for protection class I).
-
Always switch off the power supply before installation – beware of electric shock.
-
Installation and maintenance of the lamp must be carried out by a qualified professional.
-
Do not use the product in a potentially explosive environment, danger to life!
-
Keep children away from the spotlight. Children cannot assess the danger from the electric current.
-
Please never look directly into the light.
-
A destroyed protective cover cannot be replaced. The lamp must be disposed of.
-
Not suitable for operation with external dimmers.
TECHNICAL DATA
| Protection class: | I |
|---|---|
| Nominal voltage: | 220-250 V~ 50/60 Hz |
| Protection class versions with/without motion detector: | IP 54 |
| Temperature range: | -20 °C bis +50 °C |
| Connection cable: | H05RN-F 3G1.0 mm² (not supplied) |
| Radio frequency: | 2.4 GHz |
| WiFi Frequency band: | 2.412-2.484 GHz |
| Max. transmission power: | <100 mW |
| Wireless IEE standards: | IEEE 802.11 b/g/n |
| Model | WF 2050 |
| --- | --- |
| Motion detector (PIR) | – |
| Power input (W) | 19,5 |
| Current max. (A) | 0.136 |
| Leistungsfaktor | > 0.5 |
| max. projected area (cm²) | 190 |
| Dimensions (mm) | 160x119x118 |
| Weight (kg) | 0.56 |
This LED spotlight is suitable for indoor and outdoor lighting purposes.
INSTALLATION AND CONNECTION TO POWER SUPPLY
see illustrations
-
Always switch off the power supply before installation.
-
The lamp must be mounted at a height of less than 3 m
Recommended installation height for models with motion detector 2.5 m. -
To attach the mounting plate to the wall, follow the steps as described in 1+2.
-
Insert the power cable through the rubber seal of the mounting plate and screw it to the wall 3.
Cover the openings for the screws with the sealing cap. Fasten the cable with the strain relief if necessary. -
Connect the strands of the power cable with the luster terminal of the lamp 4.
Note the wires N and L. -
Connect the lamp with the mounting plate 5 and tighten the screw.
-
Align the lamp head(s).
-
Switch on the power supply again.
OPERATION with WIFI (for setting the light and PiR parameters)
-
Start the App brennenstuhl® Connect.
-
Use the „+“ symbol to add new devices.
-
Select in the device overview with the type No. to select the device to be installed.
-
Set the lamp to the learning mode:
Press the reset button 3 times, if the learning mode is active, the lamp will start blinking. -
Then follow the instructions in the app to connect the WiFi lamp to your network.
If the spotlight is set up in the app, all settings can be made in the app.
SCOPE OF DELIVERY
2x screws, 2x dowels, 1x rubber seal.
CLEANING
Disconnect the product from the mains voltage before cleaning.
Do not use solvents, caustic cleaning agents or similar products. Only use a
dry or slightly moistened cloth for cleaning.
MAINTENANCE
CAUTION: The LED light does not contain any components that require main- tenance. The light source of this light is not replaceable. When the light source has reached the end of its service life, the entire light must be replaced. The light must not be opened.
SIMPLIFIED EU DECLARATION OF CONFORMITY
We, the Hugo Brennenstuhl GmbH & Co. KG, herewith declare that the remote
system types WF 2050 / WF 2050 P / WFD 3050 / WFD 3050 with the directives
2014/53/EU and 2011/65/EU. The complete text of the EU declaration of
conformity is available at the following web addresses.
www.brennenstuhl.com/konformitaetserklaerung/ke_1179050000.pdf
www.brennenstuhl.com/konformitaetserklaerung/ke_1179050010.pdf
www.brennenstuhl.com/konformitaetserklaerung/ke_1179060000.pdf
www.brennenstuhl.com/konformitaetserklaerung/ke_1179060010.pdf
For possibilities of disposal of the used product, please contact your local or municipal administration.
DISPOSAL
Electronic appliances must not be disposed of in household waste!
The European Directive 2012/19/EC on Waste Electrical and Electronic Equipment
and its
implementation on national law stipulate that used electronic appliances
should be collected
separately and recycled in an environmentally friendly manner. For
possibilities of disposal of the used
appliance, please contact your local or municipal administration.
MANUFACTURER
Hugo Brennenstuhl GmbH & Co. KG
Seestraße 1 – 3 · D-72074 Tübingen
H. Brennenstuhl S.A.S.
4 rue de Bruxelles ∙ F-67170 Bernolsheim
lectra technik ag
Blegistrasse 13 · CH-6340 Baar
For further information, please refer to the Service/FAQ section on our
homepage www.brennenstuhl.com.
Smart up your home.
www.brennenstuhl.com
Hugo Brennenstuhl GmbH & Co. KG
Seestraße 1-3 ∙ D-72074 Tübingen
H. Brennenstuhl S.A.S.
4 rue de Bruxelles ∙ F-67170 Bernolsheim
lectra technik ag
Blegistrasse 13 ∙ CH-6340 Baar
www.brennenstuhl.com
0533088/1321
30.03.21 08:03
070820 BA_WiFi Strahler 0533088.indd
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>