VENETA 65101-40168-E Cordless Dual Blinds

How to install your Dual Blinds Cordless (Roller Blinds with Raceway)

65101-40168-E

Required Tools

Included Hardware

The hardware can be found in the small hardware box included with your blind.

• 32mm Hexagon Screw (for Mounting Bracket)
• 19mm Round Head Screw
• Mounting Bracket (for Inside Mount)
• Blind Bracket Cover
• Top Light Guard Holder (for Inside Mount)
• Mounting Brackets (for Outside Mount)
• Traditional Hold Down Bracket (Optional)
• Handle

Installing inside the window frame

Blind Bracket Installation

1. CD See instructions below to locate the correct brackets first. Left blinds bracket with lug at bottom. Right blinds bracket with lug at top.
2. Attach the Blind brackets and extensions into the two ends of the raceway.
3. Make sure the extension bolt locks into the raceway’s dedicated hole.
4. Insert the top light guard holder horizontally into the groove at the backside of raceway and turn 90 degrees to lock in the raceway groove. Then insert the top light guard into the groove of the top light guard holder.
5. First fit the blind bracket cover over the blind bracket. Install the raceway into the window opening. We recommend securing the screws into the middle holes of the raceway first. This would allow you to adjust the raceway left or right if required. Once the correct position has been located, secure the screws for the holes. Take care that the distance between the l st screw and the window edge is at least 19mm.
6. The hem bars of both the front & back blinds should be at the same height.

Blind Installation and Removal

Installation of the Blind … Always start with the back blind before installing the front blind.

1. The tension dial side will be at the left side of back blind. First, insert the tension dial of back blind into the lug at bottom of left bracket.
2. Second, press the end plug and insert the end plug end into the hole of bracket of the other side.The gap on end plug end needs to be about 4.5mm.
3. Finally slide the lock pin in the blind bracket downward into the end plug to prevent the blind from falling.
4. The tension dial side will be at the right side of front blind. Repeat the above steps for front blinds.

Blind Installation Tips … After blind is installed into blind brackets, use a Level to check if the fabrics roll is horizontal; if not, please adjust the position of blind brackets to keep the fabrics roll level. Removal of the Blind … Always remove the front blind first.

1. Use a tool to push the lock pin on end plug bracket upward.
2. Use tool to draw back the end plug from bracket.
3. Finally remove blind from mounting bracket.

Installing outside the window frame

Blind Bracket Installation

1. Measure 75mm in from top left and top right of where the blind will sit, and mark where the screws will go.
2. When installing the mounting bracket, the distance from the bracket’s mounting hole to the edge of the window frame should be at least 19mm.
3. Make sure all brackets line up with each other horizontally. Each bracket will require two 32mm hexagon screws for the installation.
4. If more brackets are supplied, space them evenly between the first two brackets.

Blind Installation and Removal

Before installing the shade into the mounting brackets, please locate the lock pin in the shade bracket on the end plug side. Slide the pin downward into the end plug to prevent the shade from falling.

There are two ways to attach the shade to mount brackets….

Insert the back edge of the raceway into the back plastic part of the bracket, and then turn the raceway upwards so that the front rib of the raceway snaps into the bracket.Snap the front rib of the raceway into the bracket, and then turn the raceway backwards and upwards so that the back of the raceway is stuck to the back plastic part of the bracket.

The hem bars of both the front & back blinds should be at the same height.

Removal of the Blind…

1. Use a tool to push back the front or back plastic part of the brackets.
2. Turn the back side of the raceway downward so that it detaches from the bracket.
3. Finally remove the raceway by pulling downward from the brackets.

Handle installation and Removal

Attach Handle to Hem Bar…

• Step 1: Turn over hem bar and you can see a label attached at the center of the hem bar.
• Step 2: Align the center of the bottom of the handle with the label.
• Step 3: Hook the handle to the hem bar from top to bottom.
• Step 4: Press the handle from top to bottom to make the top of the handle clip into the hem bar.
• Step 5: Tear off the label from hem bar.

Remove handle from hem bar… Use straight screwdriver to pry the bottom of Handle from hem bar and then the handle can be removed.

Hold Down Brackets Installation (optional)

Use 19mm round head screw to secure each bracket.

Cordless Operation

The blind must be installed on the brackets when adjusting.

Great Job… Enjoy your new Veneta Blinds!

Dusting

Dust can be removed using a feather duster or vacuum with brush attachment on low suction.

Spot Cleaning

• Use a warm damp cloth or a mild detergent for tougher stains.
• Dab the affected area, but do not rub the fabric. Finish with just a warm damp cloth.
• Allow the fabric to dry in the lowered position.

Feedback?

We would love to know how you went with your installation…  Please write a review on our website at…
www.venetablinds.com.au

Maintaining your Blind

Need HELP?
Call our Customer Service team for assistance
1300 836 382

VENETABLINDS.COM.AU

References

• Veneta® Blinds: Online Blinds | Shop Window Blinds Made To Measure – Veneta Blinds

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>