VENETA 65101-40160-D Roller Blinds with Raceway Installation Guide

VENETA 65101-40160-D Roller Blinds with Raceway

Required Tools

Included Hardware

The hardware can be found in the small hardware box included with your blind.

• 32mm Hexagon Screw (for Mounting Bracket)
• 19mm Round Head Screw
• 19mm Round Head Screw
• Blind Bracket (on Tension Dial for Inside Mount)
• Blind Bracket (on End Plug end for Inside Mount)
• Blind Bracket Cover
• Mounting Brackets (for Outside Mount) Traditional Hold
• Down Bracket (for Inside Mount)
• Handle

Installing inside the window frame

Blind Bracket Installation

1. Attach the blind brackets and extensions to the two ends of the raceway. Please decide whether the tension dial is at the left or right side of the blind first, the side with the tension dial should use the tension dial end bracket.
2. Make sure the extension bolt locks into the raceway’s dedicated hole.
3. First, fit the blind bracket cover over the blind bracket. Install the raceway into the window opening. We recommend securing the screws into the middle holes of the raceway first. This would allow you to adjust the raceway left or right if required. Once the correct position has been located, secure the screws for the holes.
4. Take care that the distance between the 1st screw and the window edge is at least 19mm.

Blind Installation and Removal

Installation of the Blind.

1. First, insert the tension dial into the tongue of the tension dial bracket.
2. Second. Press the end plug and insert the end plug end into the hole of the bracket on the other side.
3. Finally slide the lock pin in the blind bracket downward info the end plug to prevent the blind from falling. The gap on the end plug end needs to be about 4.5mm.

Blind Installation Tips.
After the blind is installed into blind brackets, use a level to check if the fabric’s roll is horizontal; if not, please adjust the position of the blind brackets to keep the fabric’s roll level.

Removal of the Blind.

1. Use a tool to push the lock pin on the end plug bracket upward.
2. Use a tool to draw back the end plug from the bracket.
3. Finally, remove the blind from the mounting bracket.

Installing outside the window frame

Blind Bracket Installation

1. Measure 75mm in from the top left and top right of where the blind will sit, and mark where the Screws will go.
2. When installing the mounting bracket, the distance from the bracket’s mounting hole to the edge of the window frame should be at least 19mm.
3. Make sure all brackets line up with each other horizontally. Each bracket will require two 32mm hexagon screws for installation.
4. If more brackets are supplied, space them evenly between the first two brackets.

Blind Installation and Removal

Before installing the shade into the mounting brackets, please locate the lock pin in the shade bracket on the end plug side. Slide the pin down into the end plug to prevent the shade from falling.

There are two ways to attach the shade to mount brackets.
A. Insert the back edge of the raceway into the back plastic part of the bracket, and then turn the raceway upwards so that the front rib of the raceway snaps into the bracket.

B. Snap the front rib of the raceway into the bracket, and then force the raceway backward and upwards so that the back of the raceway is sfuck of the back plastic part of the bracket.

Removal of the Blind.

1. Use a tool to push back the front or back plastic part of the brackets.
2. Turn the back side of the raceway downward so that it detaches from the bracket.
3. Finally, remove the raceway by pulling it down from the brackets.

Handle installation and Removal

Attach Handle for, Hem Bar.

• Step 1: Turn over the hem bar and you can see a label attached at the corner of the hem bar.
• Step 2: Align the center of the bottom of the handle with the label.
• Step 3: Hook the handle for the hem bar from the top to the bottom.
• Step 4: Press the handle from top to bottom to make the top of the handle clip into the hem bar.
• Step 5: Tear off the label from the hem bar.

Remove the handle from the hem bar.

• Use the straight screwdriver to pry the bottom of handle from the hem bar and then the handle can be removed

Hold Down Brackets Installation (optional

• Use a 19mm round head screw to secure each bracket.

Cordless Operation

• The tension in our cordless roller blind can be adjusted to provide optimal light control and to ensure easy and dependable operation on a variety of window types and sizes. If a cordless blind begins to slide down on its own or it fails to roll up, the issue can be easily fixed by turning the adjustment dial towards”+” to increase the tension.
• Conversely, if the cordless blind cannot stop at the desired height and tends to roll up by itself, the tension can be decreused by learning The adjustment dial towards Ithe
  The blind must be installed on the brackets when adjusting

Great Job… Enjoy your new Veneta Blinds!

Dusting

• Dust can be removed using a feather duster or vacuum with a brush attachment on low suction.

Spot Cleaning

• Use a warm damp cloth or a mild detergent for tougher stains.
• Dab the affected area, but do not rub the fabric. Finish With just a warm damp cloth.
• Allow the fabric to dry in the lowered position.

Maintaining your
Blind
Need HELP?
Call our Customer service Team for assistance 1300 836 382
Feedback?
We would love to know how yo went with your installation…
Please write a review on ou website at… www.venetablinds.com.au

Documents / Resources

| VENETA 65101-40160-D Roller Blinds with Raceway [pdf] Installation Guide
65101-40160-D Roller Blinds with Raceway, 65101-40160-D, Roller Blinds with Raceway, Roller Blinds, Blinds
---|---

References

• Veneta® Blinds: Online Blinds | Shop Window Blinds Made To Measure – Veneta Blinds

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>