VENETA N301246 Cordless Roller Shade Instruction Manual

Cordless Roller Shade
Installation Instruction
N301246 With Raceway

Recommended Tools

• Screw gun / Drill
• Tape Measure
• Screwdriver
• Level
• Pencil

Hardware Included
Screws needed for installing

Hardware for Roller shade with Raceway System

Hardware| Drawing|

Usage

---|---|---
Shade bracket (for flush inside mount)| | To install shade (on Clutch end)
| To install shade (on End Plug end)
Mounting bracket (for outside mount)| | To install Raceway (on Clutch end)
| To install shade (on End Plug end)
Mid Mounting Bracket (for outside mount)| | As support for Raceway when needed. 1 Mid mounting bracket should be attached to the shade when width > 40”
Shade bracket cover| | Bracket cover
Handle| | For Cordless Shades

Shade Bracket Installation

※Installation of Roller Shade with Raceway System (Inside Mount)
Attach the shade brackets and extensions into the two ends of the raceway. Make sure the extension bolt locks into the raceway’s dedicated hole. Install the shade and raceway system into the window opening. It is better to screw the middle holes on raceway to make sure the raceway location can be adjusted to left or right, after the raceway has been located at proper position, and then screw other screw holes. Taking care that the distance between the 1 st screw and the window edge is at least 3/4”.

※Installation of Roller Shade with Raceway System(Outside Mount)
Like inside mount, firstly attach the end brackets and extensions into the two ends of the raceway. Make sure the extension bolt locks into the raceway’s dedicated hole.

For shade with width>40”, make sure the top groove of the mid mounting bracket hook onto the top of the raceway while the bracket’s bottom groove clips into the bottom rib of the raceway, as shown below. Middle brackets should be installed before shade brackets on raceway ends.
Middle Mounting Bracket

When installing the raceway onto the window opening, the top of each mounting bracket needs to be parallel with the edge of the window frame. The distance from the shade bracket’s mounting holes to the front edge of the window frame should be at least 3/4”. Make sure all the shade brackets are level and aligned with each other. Each shade bracket will require two 1 1/4” hexagon screws for the installation.

The space between each mounting bracket should be divided evenly as pictured.

Shade Installation and Removal

1. First, insert the Clutch end into the tongue of clutch bracket
2. Second, press the end plug and insert the End Plug end into the hole of bracket of the other side.
3. And then attach bracket covers to brackets and locate the pin. As shown below: Finally, remove the paper band from the shade by hand.

Shade Installation Tips: After shade is installed into shade bracketsuse a Level to check if the tube of shade is horizontal; if not, pleaseadjust the position of shade brackets to keep the tube level. ※Removal of Roller Shade with Raceway System

• Use a tool to push the lock pin on end plug bracket upward①
• Use tool to draw back the end plug from bracket②
• Finally remove shade from mounting bracket. As shown drawing③

How to install or remove Handle for Cordless Shade

• Attach Handle to Hem Bar

Turn over hem bar and you can see a label attached at the center of hem bar. Align the center of the bottom of handle with the label and hook the handle to the hem bar from top to bottom.
Press the handle from top to bottom to make the top of handle clip into the hem bar.
Finally tear off the label from hem bar.

• Remove handle from hem bar

Use straight screwdriver to pry the bottom of Handle from hem bar and then handle can be removed.

Roller Shade Operation

Documents / Resources

| VENETA N301246 Cordless Roller Shade [pdf] Instruction Manual
N301246 Cordless Roller Shade, N301246, Cordless Roller Shade, Roller Shade, Shade
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>