VENETA 65101 Dual Blinds Cordloop Smart Release Roller Blinds Instruction Manual
- June 9, 2024
- Veneta
Table of Contents
VENETA 65101 Dual Blinds Cordloop Smart Release Roller Blinds Instruction
Manual
Required Tools
Included Hardware
The hardware can be found in the small hardware box included with your blind.
Installing inside the window frame
1. Blind Bracket Installation
- See instructions below to locate the correct brackets first. Left blinds bracket with lug at bottom. Right blinds bracket with lug at top.
- Attach the Blind brackets and extensions into the two ends of the raceway.
- Make sure the extension bolt locks into the raceway’s dedicated hole.
- Insert the top light guard holder horizontally into the groove at the backside of raceway and turn 90 degrees to lock in the raceway groove. Then insert the top light guard into the groove of the top light guard holder.
- First fit the blind bracket cover over the blind bracket. Install the raceway into the window opening. We recommend securing the screws into the middle holes of the raceway first. This would allow you to adjust the raceway left or right if required. Once the correct position has been located, secure the screws for the holes. Take care that the distance between the 1st screw and the window edge is at least 19mm.
- The hem bars of both the front & back blinds should be at the same height.
2. Blind Installation and Removal
WARNING
ALL WINDOW COVERINGS WITH CORD OR CHAIN
To avoid creating a possible strangulation hazard for children, the corded or chained internal window covering must be installed in such a way that a loose cord or chain cannot form a loop 220 mm or longer at a height of less than 1600 mm above floor level.
- A cord/chain guide may be installed lower than 1600mm above floor level if the cord/chain is sufficiently secured or tensioned to prevent a loop 220 mm or longer from being formed.
- If a cord/chain guide is installed lower than 1600 mm above floor level, it must be designed to prevent a child from being able to remove the cord/chain.
- If a cleat is used to secure the cord, it must be at least 1600 mm above floor level because a child is capable of unwinding a cord from a cleat.
www.venetablinds.com.au/child-safety
Installing outside the window frame
1. Blind Bracket Installation
- Measure 75mm in from top left and top right of where the blind will sit, and mark where the screws will go.
- When installing the mounting bracket, the distance from the bracket’s mounting hole to the edge of the window frame should be at least 19mm.
- Make sure all brackets line up with each other horizontally.
- Each bracket will require two 32mm hexagon screws for the installation.
- If more brackets are supplied, space them evenly between the first two brackets.
2. Blind Installation and Removal
Before installing the shade into the mounting brackets, please locate the lock pin in the shade bracket on the end plug side. Slide the pin downward into the end plug to prevent the shade from falling.
There are two ways to attach the shade to the mount brackets….
Removal of the Blind….
- Use a tool to push back the front or back plastic part of the brackets.
- Turn the back side of the raceway downward so that it detaches from the bracket.
- Finally remove the raceway by pulling downward from the brackets.
Feedback?
We would love to know how you went with your installation…
Please write a review on our
website at…
SmartRelease™…
For the operation of SmartRelease™, gently pull the bead chain which is closer to the blind fabric downwards about 40mm and the blind will lower automatically. If there is a need to stop the blind while it is lowering, pull the bead chain which is farther away from the blind fabric and the blind will stop. If the blind cannot lower automatically after gently pulling the bead chain which is closer to the fabric, pull the bead chain which is further away from the fabric first, and then pull the bead chain on the other side.
Great Job… Enjoy your new Veneta Blinds!
Maintaining your Blind
1. Dusting
Dust can be removed using a feather duster or vacuum with brush attachment on
low suction.
2. Spot Cleaning
Use a warm damp cloth or a mild detergent for tougher stains.
Dab the affected area, but do not rub the fabric. Finish with just a warm damp
cloth.
Allow the fabric to dry in the lowered position.
Need HELP?
Call our
Customer Service team for assistance
1300 836 382
Read More About This Manual & Download PDF:
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>