THOMSON Design UHD Antenna Sculpture Instruction Manual

THOMSON Design UHD Antenna Sculpture

Operating instruction

Thank you for choosing a Thomson product.
Take your time and read the following instructions and information completely. Please keep these instructions in a safe place for future reference. If you sell the device, please pass these operating instructions on to the new owner.

Controls and Displays

1. Micro-USB input
2. Antenna cable
3. On/off switch / Gain control (Off/STD/Turbo)
4. Base
5. Eyelets for wall bracket
6. Amplifier adapter

Explanation of Warning Symbols and Notes

Warning
This symbol is used to indicate safety instructions or to draw your attention to specific hazards and risks.
Note
This symbol is used to indicate additional information or important notes.

Package Contents

• DVB-T Indoor Antenna
• USB cable
• Base
• Amplifier adapter
• These operating instructions

Safety Notes

The product is intended for private, non-commercial use only.

• The product is intended for indoor use only.
• Use the product for its intended purpose only.
• Protect the product from dirt, moisture and overheating and use it in dry rooms only.
• Children should be supervised to ensure that they do not play with the device.
• Do not use the product in areas where the use of electronic devices is not permitted.
• Connect the product only to a socket that has been approved for the device. The electrical socket must always be easily accessible.
• Disconnect the product from the network using the power button – if this is not available, unplug the power cord from the socket.
• Lay all cables so that they do not pose a tripping hazard.
• Do not bend or crush the cable.
• Do not drop the product and do not expose it to any major shocks.
• Dispose of packaging material immediately according to locally applicable regulations.
• Do not modify the device in any way. Doing so voids the warranty

Warning

• Do not use the product if the AC adapter, adapter cable or power cable is damaged.
• Do not attempt to service or repair the device yourself. Leave any service work to qualified experts.
• Do not open the device or continue to operate it if it becomes damaged.

Specifications

Getting started and operation

Powering the antenna using the antenna cable (Fig. 2a)

• Connect the antenna cable from the antenna to the antenna input on the amplifier adapter (6) and the antenna cable from the amplifier adapter to the antenna input on the digital TV or set-top box.
• Switch on the antenna by sliding the On/off switch (3) to the ‘STD’ or ‘Turbo’ position.
• Switch on the digital TV (or the set-top box and TV).

Note
Powering the antenna directly from the set-top box or digital TV requires a supply voltage of 5 V. Note that the voltage of +5 V is provided by the set- top box and/or digital TV. Make any necessary settings in the menu

Powering the antenna directly using the USB port of the digital TV /

set-top box (Fig. 2b)

• Connect the antenna cable from the antenna to the antenna input on the amplifier adapter (6) and the antenna cable from the amplifier adapter to the antenna input on the digital TV or set-top box.
• Connect the USB cable to the amplifier adapter (6) and an unused USB port on your TV or set-top box.
• Switch on the antenna by sliding the On/off switch (3) to the ‘STD’ or ‘Turbo’ position.
• Ensure that the set-top box or digital TV is switched on.

Powering the antenna using an external power supply unit (Fig. 2c)

• Connect the antenna cable from the antenna to the antenna input on the amplifier adapter (4) and the antenna cable from the amplifier adapter to the antenna input on the digital TV or set-top box.
• Connect the USB cable to the amplifier adapter (6) and to a suitable USB power supply unit (not included) and plug the latter into a socket
• Switch on the antenna by sliding the On/off switch (3) to the ‘STD’ or ‘Turbo’ position.
• Switch on the digital TV (or the set-top box and TV).

Standing the antenna / wall mounting

The antenna can be mounted either on the wall or in a base.
In the latter case, simply insert the base into the opening provided on the rear of the antenna and push the cable into the cable guide on the base.
For wall mounting, ensure that you use suitable screws and dowels (not supplied) to secure the antenna to the wall.

Note – Wall mounting

• Before mounting, check that the wall you have chosen is suitable for the weight to be mounted Also make sure that there are no electric, water, gas or other lines running through the wall at the mounting site.
• After the product has been mounted, check that it is sufficiently secure. You should repeat this check at regular intervals.

TV reception

The amplifier power must be adjusted depending on the station; to do this, slide the gain control (3) to the ‘STD’ or ‘Turbo’ position. There are two amplification levels: STD (= 12 dB) and ‘Turbo’ (= 20 dB).

Note
Please note that the number and quality of stations received may vary depending on the position of the antenna and local conditions.

Care and Maintenance

Only clean this product with a slightly damp, lint-free cloth and do not use aggressive cleaning agents.

Warranty Disclaimer

Hama GmbH & Co KG assumes no liability and provides no warranty for damage resulting from improper installation mounting, improper use of the product or from failure to observe the operating instructions and/or safety notes.

Declaration of Conformity

Hereby, Hama GmbH & Co KG declares that the radio equipment type [00132193] is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: www.hama.com ->00132193 ->Downloads.

References

• Television, home appliances, computers, audio & video by Thomson
• hama.com
• Home

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>