LANCOM LW-500 Single Wi-Fi Access Point Instruction Manual
- June 4, 2024
- LANCOM
Table of Contents
**
**
LANCOM LW-500 Single Wi-Fi Access Point
Preparation for ceiling- or wall mounting
Use the mounting plate as a drilling template to mark out the drill holes.
Depending on the surface material the required size of the holes may vary. If
required, drill a hole into the ceiling board to feed- through the connector
cables. Alternatively, you can use the integrated cable duct on the access
point to lead the cables sideways.
Mounting to other surfaces
For mounting the device to other surfaces than described here, you may need
different mounting accessories
(screws, dowels, etc.). Pre-drilling may not be necessary when using the
included self-drilling screws.
Mounting the access point
Ceiling mounting to a wooden ceiling
Included:
1 mounting plate (A), 2 screws 2.631 mm (B),
2 screws 2.65.2/6.3 mm (C)
Place the mounting plate A to a ceiling in your desired location, insert the
screws B through the appropriate holes, and tighten the screws to fix the
plate in place. When the mounting plate is in place, insert the screws C into
the appropriate holes of the access point D. Place the access point on the
ceiling mounting plate by inserting the attached screws C into the appropriate
holes of the mounting plate. Then twist the access point D clock-wise until it
clicks into place.
Mounting to a drywall ceiling
Included:
1 mounting plate (A), 2 self-drilling screws 40 mm (E), 2 screws 3.631 mm
(B), 2 screws 2.65.2/6.3 mm (C) Screw the self-drilling screws E to the
ceiling at the previously marked positions. Screw as tight as possible until
the screw heads are flush-mounted to the ceiling to make it possible to place
the mounting plate A flat to the ceiling surface in the next step. Now align
the mounting plate A with its appropriate holes to the previously mounted
self-drilling screws E, so that the screws B can be screwed through the holes
in the mounting plate into the screw heads of the self-drilling screws E.
Tighten the screws B until the mounting plate rests backlash-free on the
mounting surface.
When the mounting plate is in place, insert the screws C into the appropriate
holes of the access point D. Place the access point on the mounting plate by
inserting the attached screws C into the appropriate holes of the mounting
plate. Then twist the access point D clockwise until it clicks into place.
T-rail mounting
Included:
4 thread screws (2 pcs. 2.610 mm, 2 pcs. 2.625 mm (F), 4 T-rail brackets (2
pcs. 15.5 mm, 2 pcs. 24.9 mm (G),
2 spacers (H)
Select the correct size of T-rail brackets G from the two sizes which are
included in the package contents. Attach the T-Rail brackets G to the
appropriate holes in the access point using the short screws F as shown. If
you need more space between the access point and the T-Rail, then additionally
use the spacers H between the brackets and the holes, and use the longer
screws F included in the package contents. Clip the access point D on to your
T-Rail using the previously attached T-Rail bracket.
Wall mounting with mounting plate
Included (as listed in chapter Mounting to a drywall
ceiling):
1 mounting plate (A), 2 self-drilling screws 40 mm (E),
2 screws 3.631 mm (B), 2 screws 2.65.2/6.3 mm (C)
Fixing the mounting plate to the wall Place the mounting plate A to a wall in
your desired location and rotate the plate to make sure that the end points 1
of the locking mechanism for fastening the access point are horizontally
aligned. In this position, use the mounting plate as a drilling template to
mark the position of the two holes 2. After having drilled the holes, use
either the screws B, B and E (as described in chapter Mounting to a drywall
ceiling), or your own mounting material to fix the mounting plate to the wall,
depending on the wall material.
Preparing the access point
Insert the screws C into the appropriate holes of
the access point D.
Fixing the access point to the mounting plate
Place the access point on the mounting
plate by inserting the attached screws C into the appropriate holes 3 of the
mounting plate. Then twist the access point clockwise 4 until it clicks into
place.
The screws C are now locked in their end positions 5 and the access point is
fixed to the mounting plate.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>