TRONIC TLD 2 A1 Wireless QI Charging Pad Instruction Manual

TLD 2 A1 Wireless QI Charging Pad
Instruction Manual WIRELESS QI ® CHARGING PAD /
KABELLOSES QI® -LADEPAD /
STATION DE CHARGE QI® SANS FIL
TLD 2 A1

TLD 2 A1 Wireless QI Charging Pad

Introduction

Information about these operating instructions
Congratulations on the purchase of your new device. You have selected a high- quality product. The operating instructions are part of this product. They contain important information about safety, usage and disposal. Before using the product, please familiarise yourself with all operating and safety instructions. Use the product only as described and for the range of applications specified. Keep these operating instructions as a reference and store them near the product. Please pass on all documentation including these operating instructions to any future owner(s) if you sell this product or give it away.
Copyright
This documentation is protected by copyright. Any copying or reproduction, including in the form of extracts, or any reproduction of images (even in a modified state), is permitted only with the written authorisation of the manufacturer.
Notes on trademarks

• USB® is a registered trademark of USB Implementers Forum, Inc.
• The word “Qi” and the Qi symbol are registered trademarks of the Wireless Power Consortium.
• iPhone 12/12 Pro, iPhone 11/11 Pro, iPhone SE, iPhone X, iPhone XR and iPhone 8/8 Plus are registered trademarks of Apple Inc., Cupertino Calif., US.
• Samsung Galaxy S20/S20+ and Note20, Samsung Galaxy S10/S10+, Samsung Galaxy S9/S9+ and Note10 are registered trademarks of Samsung.

All other names and products may be trademarks or registered trademarks of their respective owner.
Proper use
The charging pad is an information electronics device and is used to charge mobile phones. Because of the Qi technology used, only compatible mobile phones can be charged by induction charging. Compatible mobile phones are automatically detected and supplied with the appropriate output voltage and current by the device.
Any other use or use beyond that specified is considered improper use. The device is not intended for use in commercial or industrial environments. The manufacturer accepts no responsibility for damage caused by failure to observe these instructions, improper use or repairs, unauthorised modifications or the use of unapproved replacement parts. The risk is borne solely by the user.
Warnings and symbols used
The following warnings are used in these operating instructions, on the packaging and the device (where applicable):
DANGER
A warning at this hazard level indicates a hazardous situation.
Failure to avoid this hazardous situation will result in serious injuries or death.
Follow the instructions on this warning label to avoid the risk of death or serious injury.
WARNING
A warning at this hazard level indicates a potentially hazardous situation.
Failure to avoid this hazardous situation could result in serious injuries or death.
Follow the instructions on this warning label to avoid the risk of death or serious injury.
CAUTION
A warning at this hazard level indicates a potentially hazardous situation. Failure to avoid this hazardous situation could result in injuries.
Follow the instructions in this warning notice to prevent injuries.
CAUTION
A warning at this hazard level indicates a risk of property damage. Failure to avoid this situation could result in property damage.
Follow the instructions in this warning notice to prevent property damage.
NOTE
A note provides additional information that makes handling the device easier for you.
The Qi symbol indicates that the technology used enables wireless charging. Compatible devices are detected automatically and provided with the correct charging current. The output power depends on the USB power mains adapter used.

Safety

This section contains important safety instructions for handling the device. This device complies with the statutory safety regulations. Improper use may result in personal injury and property damage.
Basic safety instructions
To ensure safe operation of the device, follow the safety guidelines set out below:

• Check the device for visible external damage before use. Do not use a device that has been damaged or dropped.
• To prevent accidents, have defective plugs and/or power cables (not supplied) replaced immediately by an authorised specialist, our Customer Service or a similarly qualified person.
• This device may be used by children aged 8 years and above and by persons with limited physical, sensory or mental capacities, or lack of experience and knowledge, provided that they are under supervision or have been told how to use the device safely and are aware of the potential risks. Do not allow children to play with the device. Cleaning and user maintenance tasks may not be carried out by children unless they are supervised.
• DANGER! Do not allow children to play with the packaging material! Keep all packaging materials away from children. There is a risk of suffocation!
• Protect the connection cable from hot surfaces and sharp edges and ensure that it is not taut or kinked.
• The device should only be repaired by authorised specialist personnel or the customer service department. Improper repairs can result in hazards for the user. It will also invalidate any warranty claims.
• Do not make any unauthorised modifications or alterations to the device.
• Never open the device housing. There are no parts inside the device which require user maintenance. In addition, this will invalidate the warranty.
• Do not expose the device to water spray or dripping water, and do not place liquid-filled objects such as vases or open drink containers on or near the device.
• Keep the device away from open flames (e.g. candles) at all times.
• The device is not designed for use in rooms with high temperatures or humidity (e.g. bathrooms) or where there is excessive dust.
• Never expose the device to extreme heat.
• Do not use the device immediately after moving it from a cold room to a warm room. Always allow the device to acclimatise before turning it on.
• Do not cover the device during operation.
• Due to the high power consumption, a USB mains adapter must be used to operate the charging pad. Do not use the charging pad on a USB port of a PC or notebook.
• Make sure there are no metallic objects between the charging pad and mobile phone during operation. Metal components, such as coins, keys, or even credit cards or NFC cards, could cause the device to overheat.
• If you want to charge your mobile phone, make sure that the phone case does not contain any metal plate. Metal components could cause the device to overheat.
• Also refer to the operating instructions for your mobile phone.
• WARNING! If you notice any unusual noises, a burning smell or smoke, disconnect the connection cable from the device. Have the device checked by a qualified specialist before using it again.

Notes on the radio interface

• CAUTION! Radio interference! Never use the product in aircraft, hospitals, operating rooms or near medical electronic systems. The transmitted wireless signals could have an impact on the functionality of sensitive electrical equipment.
• WARNING! Keep the product at least 20 cm away from pacemakers or implanted cardioverter defibrillators, as electromagnetic radiation can affect the functioning of pacemakers or defibrillators.
• The transmitted radio waves may cause noise interference in hearing aids.
• Never use the product in the vicinity of flammable gases or in potentially explosive environments (e.g. paint shops), as the transmitted radio waves can trigger explosions or fires.
• Kompernass Handels GmbH is not responsible for interference with radio and television equipment caused as a result of unauthorised modification of the product.
• Furthermore, Kompernass Handels GmbH accepts no liability for the use or replacement of cables that are not sold by Kompernass Handels GmbH.
• The user of this product is solely responsible for rectifying faults caused by unauthorised modifications to the product as well as the replacement of such modified products.

Parts description/operating components

(See fold-out page for illustrations)

1. Charging surface 1
2. Connection socket (USB type-C)
3. Charging surface 2 
4. Operating LED 2
5. Operating LED 1
6. Connection cable ( USB type-A to USB type-C)
7. Operating instructions (symbol)

Using the device
Unpacking
Remove all parts and the operating instructions from the packaging.
Remove all packaging material.
Check package contents
(See fold-out page for illustrations)

• The following components are included in delivery:
• Wireless Qi® charging pad
• Connection cable 6 (USB type-A to USB type-C)
• These operating instructions 7

NOTE

• Check the package for completeness and signs of visible damage.
• If the delivery is incomplete or damage has occurred as a result of defective packaging or during transport, contact the service hotline (see section Service).

Disposal of the packaging
**** The packaging materials have been selected for their environmental friendliness and ease of disposal and are therefore recyclable. Dispose of packaging materials that are no longer needed in accordance with applicable local regulations.
Dispose of the packaging in an environmentally friendly manner. Observe the labels on the different packaging materials and separate them as needed. The packaging material is labelled with abbreviations (a) and numbers (b) with the following meanings: 1­7: plastics, 20­22: paper and cardboard, 80­98: composites.

Handling and operation

Wirelessly charging a mobile phone
CAUTION

• Operate the charging pad only in dry interior rooms.
• Due to the high power consumption, a USB mains adapter must be used to operate the charging pad. Do not use the charging pad on a USB port of a PC or notebook.
• Use only USB mains adapters with a suitable output voltage and output current for the charging pad (see section Technical data). The charging power depends on the
• USB mains adapter used. A maximum of 2×10 W is possible. Remove the connection cable 6 after you have finished charging.
• Connect the USB-A plug on the connection cable 6 to a suitable USB mains adapter (not supplied).
• Connect the USB-C plug of the connection cable 6 to the connection socket 2 of the charging pad and the USB mains adapter to a mains socket. The operating LEDs 1 4 and 2 5 light up blue for approx. 3 seconds and then go out. The device is in standby mode and ready for use.
• Place the mobile phone on the charging pad with the back facing down. Position it centrally on charging surface 1 1 or charging surface 2 3 (see fig. A). You can charge two mobile phones at the same time (see fig. B).

NOTE

• Some mobile phones need to be taken out of their case for charging.
• At ambient temperatures above 25°C, the charging power is reduced to protect against overheating. This increases the charging time of your mobile phone.
• The connection socket (USB type-C) 2 cannot be used as an output.
• Compatible mobile phones are detected automatically. If the mobile phone is not compatible, the operating LED 1 5/2 4 next to the respective charging surface 1 1/2 3 flashes blue. In this case, use a suitable adapter.
• Charging starts immediately and is indicated on the display of the mobile phone. If you are using charging surface 1 1, operating LED 1 5 lights up to indicate charging: operating LED 1 5 lights up blue continuously. If you are using charging surface 2 3, then operating LED 2 4 lights up.
• The charging progress is shown on the display of the mobile phone.
• Remove the mobile phone from charging surface 1 1/2 3 and unplug the connection cable 6 once charging is complete.

Status of the LED display
Depending on the operating status, the operating LEDs 1 5 and 2 4 behave as follows:

is ready for use
Off| Standby
The operating LED 1 5 or 2 4 goes out when the mobile phone is fully charged.
Lights up blue| Mobile phone is charged by induction
Flashes blue| Mobile phone is not compatible
Error message
Flashes green| Incompatible mains adapter or cable connected

Troubleshooting

The operating LEDs 15 and 24 do not light up for approx. 3 seconds when starting.

• Check the connection of the USB-C plug to the charging pad on the connection socket 2.
• Check the connection of the USB-A plug to the USB mains adapter (not supplied).
• Connect the USB mains adapter to another socket.

The operating LED 1 5/ 2 4 does not light up while a mobile phone is on the charging pad 1 1/2 3. (A mobile phone is not charging.)

• The cover of the mobile phone may be preventing induction charging. Remove the cover from your mobile phone.
• The mobile phone is not placed correctly on the charging pad and induction charging does not start. Check the position of the mobile phone (see section Wirelessly charging a mobile phone).

The operating LED 1 5/2 4 flashes blue.

• The mobile phone is not compatible with Qi induction charging technology and cannot be charged.
• Use a suitable adapter to charge your mobile phone by induction charging.
• Metal plates are used in some mobile phone covers. The operating LED 1 5/2 4 may react to these metal plates. Do not use the covers when induction charging. Remove them from the mobile phone beforehand.

The operating LEDs 1 5 and 2 4 flash green.

• The green flashing is triggered when an incompatible USB mains adapter or cable is used. Make sure that a compatible USB mains adapter and cable are used (USB mains adapter not supplied, see section Technical data).

NOTE

• If you cannot solve the problem with the above-mentioned solutions, please contact the Service Hotline (see section Service).

Cleaning

CAUTION

• To avoid irreparable damage to the device, ensure that no moisture gets into it during cleaning.
• Do not use caustic, abrasive or solvent-based cleaning materials. These can damage the surfaces of the device.
• Clean the device only with a slightly moistened cloth.

Storage when not in use

• Store the device in a location that is clean, dry, dust-free and out of direct sunlight.

Disposal

Disposal of the device
**** The adjacent symbol of a crossed-out dustbin means that this device is subject to Directive 2012/19/EU. This directive states that this device may not be disposed of in the normal household waste at the end of its useful life, but must be taken to specially set-up collection locations, recycling depots or disposal companies.
The disposal is free of charge for the user. Protect the environment and dispose of this device properly.
Your local community or municipal authorities can provide information on how to dispose of the worn-out product.
The product is recyclable, subject to extended producer responsibility and is collected separately.

Appendix Technical specifications

Input*2: 9 V /3 A
12 V /2.25 A
Output power| Output1: max. 2×5 W
Output2: max. 2×10 W
When connected to a QC 3.0-compatible AC/DC power supply;  mains adapter not supplied.
Frequency band| 110– kHz
Max. H-field| < 66 dBμA/m at a distance of 10 m
Max. Distance of the mobile phone to the charging surface 1 1/2 3| ≤ 5 mm
Operating temperature| +5°C up to +35°C
Storage temperature| 0°C up to +40°C
Relative humidity  (no condensation)| ≤ 75%
Dimensions| approx. 18.0 × 8.5 × 0.95 cm
Weight| approx. 90 g (without cable)

Simplified EU declaration of conformity

** Kompernaß Handels GmbH hereby declares that the radio system wireless Qi® charging pad TLD 2 A1 complies with Directive 2014/53/EU and Directive 2011/65/EU.
The complete text of the EU Declaration of Conformity is available at the following Internet address: https://dl.kompernass.com/398128_DOC.pdf
Kompernass Handels GmbH warranty
Dear Customer,
This appliance has a 3-year warranty valid from the date of purchase. If this product has any faults, you, the buyer, have certain statutory rights. Your statutory rights are not restricted in any way by the warranty described below.
Warranty conditions
The warranty period starts on the date of purchase. Please keep your receipt in a safe place. This will be required as proof of purchase.
If any material or manufacturing fault occurs within three years of the date of purchase of the product, we will either repair or replace the product for you or refund the purchase price (at our discretion). This warranty service requires that you present the defective appliance and the proof of purchase (receipt) within the three-year warranty period, along with a brief written description of the fault and of when it occurred.
If the defect is covered by the warranty, your product will either be repaired or replaced by us. The repair or replacement of a product does not signify the beginning of a new warranty period.
Warranty period and statutory claims for defects
The warranty period is not prolonged by repairs effected under the warranty. This also applies to replaced and repaired components. Any damage and defects present at the time of purchase must be reported immediately after unpacking. Repairs carried out after expiry of the warranty period shall be subject to a fee.
Scope of the warranty
This appliance has been manufactured in accordance with strict quality guidelines and inspected meticulously prior to delivery.
The warranty covers material faults or production faults. The warranty does not extend to product parts subject to normal wear and tear or to fragile parts which could be considered as consumable parts such as switches, batteries or parts made of glass.
The warranty does not apply if the product has been damaged, improperly used or improperly maintained. The directions in the operating instructions for the product regarding proper use of the product are to be strictly followed. Uses and actions that are discouraged in the operating instructions or which are warned against must be avoided.
This product is intended solely for private use and not for commercial purposes. The warranty shall be deemed void in cases of misuse or improper handling, use of force and modifications / repairs which have not been carried out by one of our authorised Service centres.
Warranty claim procedure**
To ensure quick processing of your case, please observe the following instructions:

• Please have the till receipt and the item number (IAN) 398128_2107 available as proof of purchase.
• You will find the item number on the type plate on the product, an engraving on the product, on the front page of the operating instructions (below left) or on the sticker on the rear or bottom of the product.
• If functional or other defects occur, please contact the service department listed either by telephone or by e-mail.
• You can return a defective product to us free of charge to the service address that will be provided to you. Ensure that you enclose the proof of purchase (till receipt) and information about what the defect is and when it occurred.

You can download these instructions along with many other manuals, product videos and installation software at www.lidl-service.com.
This QR code will take you directly to the Lidl service page (www .lidl-service.com) where you can open your operating instructions by entering the item number (IAN) 398128_2107.

Service
Service Great Britain
Tel.: 0800 404 7657
E-Mail: kompernass@lidl.co.uk
Service Ireland
Tel.: 1800 101010
E-Mail: kompernass@lidl.ie
IAN 398128_2107
Importer
Please note that the following address is not the service address.
Please use the service address provided in the operating instructions.
KOMPERNASS HANDELS GMBH
BURGSTRASSE 21 44867
BOCHUM GERMANY
www.kompernass.com
Last Information Update
Stanje informacij: 12 / 2021
Ident.-No.: TLD2A1-102021-V1

References

• Kompernaß - Online shop for accessories and spare parts
• de/

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>