TRONIC TPB 10000 A1 Power Bank User Manual
- June 6, 2024
- TRONIC
Table of Contents
TPB 10000 A1 Power Bank
POWER BANK / POWERBANK BATTERIE EXTERNE POWERBANK TPB 10000 A1
POWER BANK
Short manual
IAN 354192_2010
Before reading, unfold the page containing the
illustrations and familiarize yourself with all functions
of the device.
Short manual
Introduction
Information about this short manual
This document is a shortened print version of
the complete operating instructions. This short
manual does not replace the complete operating
instructions, which also contain additional
information, for example, on cleaning, troubleshooting
and the warranty.
Scan this QR code with your
smartphone/tablet. The QR code
will take you directly to the Lidl
Service page
www.lidl-service.com where you
can view and download the full
version of the operating instructions by entering
the article number (IAN) 354192_2010.
WARNING!
Observe the information in the complete operating
instructions and the safety instructions to
avoid personal injury and damage to property.
The short manual is an integral part of this product.
Before using the product, please familiarize
yourself with all operating and safety instructions.
Keep the short manual in a safe place
and hand over all documents when passing the
product on to any future owner/user.
TPB 10000 A1 GB│IE │ 3 ■
Notes on trademarks
USB® is a registered trademark of USB Implementers
Forum, Inc.
Qualcomm® Quick ChargeTM is a product made
by Qualcomm Technologies, Inc. and/or its
subsidiaries.
Qualcomm® is a trademark of Qualcomm
Incorporated, registered in the United States
and other countries.
Quick ChargeTM is a trademark of Qualcomm
Incorporated.
All other names and products may be trademarks
or registered trademarks of their respective
owner.
Intended use
This device is an information technology device
and is intended exclusively for charging mobile
devices which are charged via a USB port as
standard. The device is not intended for any
other purpose, nor for use beyond the scope
described. The device is not intended for use in
commercial or industrial environments. The manufacturer
accepts no liability for damages caused
by improper use.
Warnings and symbols used
The following warnings are used in this short
manual (where applicable):
DANGER
A warning at this hazard level
indicates
a hazardous situation.
Failure to avoid this hazardous situation will
result in serious injuries or death.
► Follow the instructions on this warning
label to avoid the risk of death or serious
injuries.
WARNING
A warning at this hazard level
indicates a potentially hazardous
situation.
Failure to avoid this hazardous situation could
result in serious injuries or death.
► Follow the instructions on this warning
label to avoid the risk of death or serious
injuries.
CAUTION
A warning at this hazard level
indicates a potentially hazardous
situation.
Failure to avoid this hazardous situation could
result in injuries.
► Follow the instructions on this warning
label to prevent injuries.
ATTENTION
A warning at this hazard level indicates
a risk of property damage.
Failure to avoid this situation could result in
property damage.
► Follow the instructions in this warning
notice to prevent property damage.
NOTE
► A note provides additional information to
help you handle the product.
This symbol can be found on the housing
of the power bank and indicates that the
contents of the operating instructions
should be followed.
The product complies with the Quick
Charge 3.0 specifications and agreements
of Qualcomm Technologies Inc.
Safety
This device complies with statutory safety regulations.
Improper use may result in personal injury
and property damage.
Basic safety instructions
■ This device may be used by children aged 8
years and above and by persons with limited
physical, sensory or mental capabilities, or
lack of experience and knowledge, provided
that they are under supervision or have been
told how to use the device safely and are
aware of the potential risks. Do not allow children
to play with the device. Cleaning and
user maintenance tasks may not be carried
out by children unless they are supervised.
■ DANGER! Do not allow children to play
with the packaging material! Keep all packaging
materials away from children.
There is a risk of suffocation!
■ Check the appliance for visible external
damage before use. Do not operate a device
which has been damaged or dropped.
■ Always place the device on a stable and
level surface. It can be damaged if dropped.
■ Do not expose the device to direct sunlight or
high temperatures. Do not cover the device
during charging. Otherwise it may overheat
and be irreparably damaged.
■ Do not place the product near heat sources
such as radiators or other heat-generating
appliances.
TPB 10000 A1 GB│IE │ 7 ■
■ Keep the device away from open flames (e.g.
candles) at all times.
■ It is not suitable for use in rooms with high
temperature or humidity (e.g. bathrooms) or
excessive quantities of dust.
■ Never expose the device to extreme heat.
This particularly applies to storage in a
car. Extreme temperatures can occur in car
interiors and glove compartments during long
periods of immobilization. Remove electrical
and electronic devices from the vehicle.
■ Do not use the device immediately after
moving it from a cold room to a warm room.
Always allow the device to acclimatize before
turning it on.
■ WARNING! Never open the device housing.
None of the components in the device
can be serviced or replaced by the user.
■ Do not make any unauthorized modifications
or alterations to the device.
■ All repairs must be carried out by authorized
specialist companies or by the customer
service department. Improper repairs may
put the user at risk. They will also invalidate
any warranty claims.
■ Do not expose the device to water spray or
dripping water, and do not place liquid-filled
objects such as vases or open drink containers
on or near the device.
■ 8 │ GB│IE TPB 10000 A1
■ WARNING! Switch the device off immediately
and disconnect any connected charging
cables from the device if you smell fumes or
notice any smoke. Have the device checked
by a qualified specialist before using it again.
■ If you are using a USB power supply,
the socket you use must always be easily
accessible so that the USB power supply can
be quickly disconnected from the socket in a
hazardous situation. You should also observe
the operating instructions for the USB power
supply.
■ WARNING! Improper use of batteries
can cause fires, explosions, leakages or other
hazards! Do not throw the device into a fire,
as the integrated battery may explode.
■ Note any restrictions or prohibitions on use
for battery-powered appliances in locations
with specific hazard risks, such as petrol
stations, aeroplanes, hospitals, etc.
Description of components
(See fold-out page for illustrations)
- Power bank
- USB-A port with QC 3.0 (output)
- USB-C port with PD 3.0 (input/output)
- Charge level LEDs
- ON/OFF button
- Charging cable (USB-A to USB-C)
- Short manual (symbol)
Setting up
Check package contents
(See fold-out page for illustrations)
The following components are included in delivery:
▯ Power bank TPB 10000 A1
▯ Charging cable
▯ This short manual
♦ Remove all parts of the device from the packaging
and remove all packaging materials.
♦ Check the package for completeness and signs
of visible damage. If the delivery is incomplete
or damage has occurred as a result of defective
packaging or during transport, contact the
Service hotline (see section Service).
Disposal of the packaging
The packaging materials have been
selected for their environmental
friendliness and ease of disposal, and
are therefore recyclable. Dispose of packaging
materials that are no longer needed in accordance
with applicable local regulations.
Dispose of the packaging in an
environmentally friendly manner.
Note the labelling on the packaging and
separate the packaging material components for
disposal if necessary. The packaging material is
labelled with abbreviations (a) and numbers (b)
with the following meanings: 1–7: plastics,
20–22: paper and cardboard,
80–98: composites.
Charging the power bank
Before using the power bank, the integrated
battery must be fully charged.
CAUTION
► Charge the device only in dry interior rooms.
► The power bank must never be charged
and used for charging an external device
at the same time.
► Due to the high power consumption, the
power bank must be charged using a USB
mains adapter. Do not charge the power
bank via the USB port of a PC or notebook.
► Use only a USB mains adapter with an
output voltage of at least 5 V and an output
current of at least 3 A to charge the power
bank.
► Disconnect the charging cable when charging
is complete!
♦ Connect the USB-A plug of the charging
cable 6 to a suitable USB power supply
(not supplied).
♦ Connect the USB-C plug of the charging
cable 6 to the USB-C charging port 3 on
the power bank.
The charge level LEDs 4 provide a rough estimate
of the charge level during charging:
LED display – Charge level
One LED is flashing < 25 %
One LED is on,
the second LED is flashing
25 ‒ 49 %
Two LEDs are on,
the third LED is flashing
50 ‒ 74 %
Three LEDs are on,
the fourth LED is flashing
75 ‒ 97 %
All LEDs are on 98 ‒ 100 %
Checking the charge level
You can also check the approximate charge
level of the power bank when it is not charging
or while it is being used for charging.
♦ Briefly press the ON/OFF button 5 once.
The LEDs 4 show the current charge level of
the power bank for about 35 seconds.
LED display Charge level
All LEDs are on 76 ‒ 100 %
Three LEDs are on 51 ‒ 75 %
Two LEDs are on 26 ‒ 50 %
One LED is on 10 ‒ 25 %
One LED is flashing < 10 %
All LEDs off 0 %
Handling and use
Charging mobile devices with the
power bank
NOTE
► You can charge up to two devices at a
time using the power bank. If both outputs
(USB-A 2 and USB-C 3) are used
simultaneously, the output voltage for both
ports is set to 5 V. Fast charging is then no
longer possible. The total power consumption
of the connected mobile devices must
not exceed 3 A.
► If the USB-A socket 2 is in fast charging
mode and the USB-C socket 3 is connected
to another device for charging, fast charging
is terminated and normal charging is activated.
All connected devices are now
charged at 5 V.
Charging via USB-A port 2
♦ Connect the supplied charging cable 6 or
the original charging cable of the device you
want to charge to the USB-A port 2.
♦ Then connect the device you want to charge
to the power bank 1. The charging process
begins automatically.
♦ If charging does not start automatically,
press the ON/OFF button 5 once briefly to
start the charging process.
Charging via USB-C port 3
♦ If your mobile device is equipped with USB
Power Delivery 3.0, you can use a USB-C
to USB-C cable (not included) to connect
the USB-C input of your device to the USB-C
port 3 of the power bank for faster charging.
Charging starts automatically as soon
as the connection is made.
♦ If charging does not start automatically,
press the ON/OFF button 5 once briefly to
start the charging process.
♦ During the charging process, the charge
level LEDs 4 show the current charge level
of the power bank (see table in the section
Checking the charge level).
♦ To stop charging, disconnect the charging
cable from the mobile device and the power
bank. The charging status LEDs 4 go out
after about 35 seconds.
♦ Optionally, you can press the ON/OFF
button 5 twice in quick succession to turn
off the power bank and the battery level
LEDs 4.
Disposal
Disposal of the device
The symbol shown on the left of a
crossed-out wheelie bin means that this
device is subject to Directive
2012/19/EU. This directive states that this
device may not be disposed of in normal
household waste at the end of its useful life, but
must be taken to a specially set-up collection
point, recycling depot or disposal company. The
integrated rechargeable battery in this device
cannot be removed for disposal.
This disposal is free of charge for the
user. Protect the environment by disposing
of this device properly.
Your local community or municipal
authorities can provide information on
how to dispose of the worn-out product.
The product is recyclable, subject to
extended producer responsibility and is
collected separately.
Appendix
Technical data
Integrated battery
(lithium polymer)
3.7 V / 10000 mAh /
37 Wh
USB-C with PD 3.0
Input voltage/
current
5 V (DC) / 3 A
9 V / 2 A
12 V / 1.5 A
USB-C port with
PD 3.0 output
voltage/current
5 V / 3 A
9 V / 2 A
12 V / 1.5 A
USB-A port with
QC 3.0
Output voltage/
current
5 V / 3 A
9 V / 2 A
12 V / 1.5 A
Maximum output
power
18 W
Maximum output
current
3 A
Minimum output
current
approx. 80 mA
Operating
temperature
5°C ‒ 35°C
Storage
temperature
0°C ‒ 40°C
Relative humidity
(no condensation)
≤ 75%
Dimensions approx. 9.8 x 6.4 x 2.4 cm
Weight approx. 195 g
- When both outputs are being used at the same
time, the output voltage for both outputs is fixed
at 5 V and the total power consumption of the
connected mobile devices must not exceed
3 A. The output power is reduced to 15 W.
Service
Service Great Britain
Tel.: 0800 404 7657
E-Mail: kompernass@lidl.co.uk
Service Ireland
Tel.: 1890 930 034
(0,08 EUR / Min., (peak))
(0,06 EUR / Min., (off peak))
E-Mail: kompernass@lidl.ie
IAN 354192_2010
Importer
Please note that the following address is not the
service address. Please use the service address
provided in the operating instructions.
KOMPERNASS HANDELS GMBH
BURGSTRASSE 21
44867 BOCHUM
GERMANY
www.kompernass.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>