RAB PIR-S-SPIR-S PIR Motion Sensor Instructions
- June 2, 2024
- RAB
Table of Contents
PIR-S-SPIR-S PIR Motion Sensor
Instruction Manual
RAB Lighting is committed to creating high-quality, affordable, well- designed and energy-efficient LED lighting and controls that make it easy for electricians to install and end users to save energy. We’d love to hear your comments. Please call the Marketing Department at 888-RAB-1000 or email: marketing@rablighting.com
PIR-S-SPIR-S PIR Motion Sensor
HID-XXX-V-EX39-8XX-BYP-HB-G2 Our sensor product numbers include MW-S/SMW-S,
PIR-S/SPIR-S and DAYLIGHT-S are optional accessories for select High Bay
lamps. The lamps will perform as normal if no sensor is inserted. Please note
that RAB lamps can’t operate with other brand sensors. 
IMPORTANT
READ CAREFULLY BEFORE INSTALLING LED HID BULBS. RETAIN THESE INSTRUCTIONS FOR
FUTURE REFERENCE.
RAB LED HID Bulbs must be wired in accordance with the National Electrical
Code and all applicable codes. Proper grounding is required for safety THIS
PRODUCT MUST BF INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTAL ATION CODE
BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THF PRODUCT AND
THE HAZARDS INVOIVFD
WARNINGS:
- Main applications include for use in high bay and other suitable light fixtures.
- Operating temperature: -30°C to 60C(-22F to 140°F).
- These LED Lamps require all ballasts, capacitors, and ignitors to be bypassed or removed. Do not operate lamps on existing ballasts.
- Dimmable with optional control modules.
- Do not use with standard dimmers. Only use the control provided with or specified by these instructions to control this lamp. This lamp will not operate properly when connected to a standard (incandescent) dimmer or dimming control.
- This device is not intended for use with emergency exits.
- For use in enclosed fixtures.
- Before installation make certain the AC power to the fixture is off.
- Risk of fire or electric shock. Luminaire wiring and electrical parts may be damaged when drilling for installation of LED retrofit kit. Check for enclosed wiring and components.
- Risk of fire or electric shock. LED Retrofit lamp installation requires knowledge of luminaires electrical systems. If not qualified, do not attempt installation. Contact a qualified electrician.
- Do not make or alter any open holes in an enclosure of wiring or electrical components during kit installation.
- Installers should not disconnect existing wires from lampholder terminals to make new connections at lampholder terminals. Instead installers should cut existing lampholder leads away from the lampholder and make new electrical connections to lampholder lead wires by employing applicable connectors.
- To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or other sharp objects.
- Risk of fire or electric shock. Install this kit only in luminaires that have the construction features and dimensions shown in the photographs or drawings and where the input rating of the retrofit kit does not exceed the input rating of the luminaire.
- Use only with a portable luminaire that is provided with a shade.
- Added weight of the device may cause instability of a free-standing portable luminaire.
- THIS RETROFIT KIT IS ACCEPTED AS A COMPONENT OF A LUMINAIRE WHERE THE SUITABILITY OF THE COMBINATION SHALL BE DETERMINED BY AUTHORITIES HAVING JURISDICTION.
INSTALLATION INSTRUCTION
Burning positions:
base up
You must use the safety cable to secure the lamps in case of falling down due
to old socket Attach one end of the safety cable to the lamp and the other end
to the luminaire.
Note: These instructions do not cover all details or variations in equipment nor do they provide for every possible situation during installation, operation or maintenance.
LAMP INSTALLATION
Step:1 Turn off the power before installation. As shown in Figure 1 Remove the old Ballast, Capacitor and Ignitor (if existing).
Step:2 As shown in Figure 2 Make sure the Alternating Current Wires
connect to the socket directly. (Reattach or replace ground lead if one is
needed).
Step:3 As shown in Figure 3 Screw the LED lamp into the corresponding
socket. Attach retrofit label to luminaire.
Securely fasten the ground wire to the main body structure. If the wire is damaged in any way please replace (Do not use existing burnt out wire). If needed, the replacement ground wire must be 1.0mm in size and insulated from heat.
© 2023 RAB LIGHTING Inc.
Cranbury, New Jersey 08512USA
COHB-IN-0123
rablighting.com Visit our website for product info
Tech Help Line Call our experts: 888 722-1000
e-mall Answered promptly –
sales@rablighting.com
Free Lighting Layouts Answered online or by request
RAB WARRANTY: RAB’s warranty is subject to all terms and conditions found at
rabfighting.com/warranty.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>