SUPERATV Front High Clearance 1 1 by 2 Inch Offset A Arms for Kawasaki Mule FXT Instruction Manual
- June 4, 2024
- SUPERATV
Table of Contents
2753 Michigan Road
• Madison, Indiana 47250
•855-743-3427
INSTALLATION INSTRUCTIONS
Front High Clearance 1-1/2” Offset A-Arms:
for Kawasaki Mule FXT™
Front High Clearance 1 1 by 2 Inch Offset A-Arms for Kawasaki Mule FXT
A Press or Ball Joint tool is required to remove and install Ball
Joints.C
Keep all components removed from machine
PIVOT BLOCK SETTINGS
- Place new A-Arms onto a flat surface and verify the dimensions shown.
- A negative 1° camber setting is achieved when Pivot Blocks are set to this dimension.
- See page 8 for additional camber information.
Leave Jam Nuts loose. Tighten after final adjustments have been made.
- Install Steering Stop onto Rack and Pinion shaft.
- Install Ball and Socket; use Loc-Tite.
– Repeat for the opposite side.
– Install Lower A-Arms to Frame with stock hardware. Do not install Nuts until
all final adjustments have been completed.
– Install Upper A-Arms to Frame with stock hardware. SuperATV recommends using
Loc-Tite on Nuts.
– Reinstall Knuckles to A-Arms with stock hardware. Do not install nuts to
Lowers until all final adjustments have been completed.
– Reinstall Shocks and Tie Rod Ends with stock hardware.
– Reinstall Tires and see the following page for Camber adjustments if
required.
– Add Nuts to previously installed hardware and tighten completely. SuperATV
recommends using Loc-Tite on Nuts.
CAMBER
- Tires must have equal air pressure before making adjustments.
- Adjustments to be made after all suspension components have been completely assembled.
- Tires must not be in contact with the ground when making adjustments.
- Perform adjustments in small increments.
Adjusting Camber:
- Remove A-Arms from Frame and turn Pivot Blocks to adjust the camber. Reinstall Arms.
- Lower the machine and settle suspension components by rolling the machine back and forth several feet at a time.
- Check settings and make small adjustments as needed.
- Each time an adjustment is made, the machine must be rolled back and forth to settle suspension components.
- Once the desired setting is achieved, tighten the hardware completely. Loc-tite on Nuts is recommended.
A NEGATIVE CAMBER SETTING OF 1° to 2° IS RECOMMENDED.
LOWER:
Too much positive camber: adjust Pivot Blocks OUT.
Too much negative camber: adjust Pivot Blocks IN.
note: 2 full turns is 1°
UPPER A-ARMS:
Too much positive camber: adjust Pivot Blocks IN.
Too much negative camber: adjust Pivot Blocks OUT.
note: 2 full turns is 1°
– Secure Brake Lines to Upper A-Arms with hardware shown.
Liability Statement
SuperATV’s ® products are designed to best fit the user’s ATV/UTV under stock
conditions. Adding, modifying, or fabricating any factory or aftermarket parts
will void any warranty provided by SuperATV ® and is not recommended.
SuperATV’s ® products could interfere with other aftermarket accessories. If
user has aftermarket products on the machine, contact SuperATV ® to verify
that they will work together.
Although SuperATV ® has thousands of satisfied customers, user should be aware
that installing lift kits, long travel, or suspension kits, tires, etc. will
change the ride of the machine and may increase maintenance and part wear.
Operating any off-road machine while, or after, consuming alcohol and/or drugs
increases the risk of bodily harm or death. No warranty or representation is
made as to this product’s ability to protect user from severe injury or death.
SuperATV ® urges operators and occupants to wear a helmet and appropriate
riding gear at all times.
By purchasing and installing SuperATV ® products, user agrees that should
damage occur, SuperATV ® will not be held responsible for loss of time, use,
labor fees, replacement parts, or freight charges. SuperATV ® , nor any 3rd
party, will not be held responsible for any direct, indirect, incidental,
special, or consequential damages that result from any product purchased from
SuperATV ® . The total liability of the seller to the user for all damages,
losses, and causes of action, if any, shall not exceed the total purchase
price paid for the product that gave rise to the claim.
SuperATV ® will warranty only parts provided by SuperATV ®. Any damage or
problems with OEM housings, bearings, seals, or other manufacturers’ products
will not be covered by SuperATV ® . SuperATV ® parts and products are not
warranted if the item was not installed properly, misused, or modified.
Installing, adding, modifying, or fabricating any factory or aftermarket
product to your ATV/UTV may violate certain local, state, and federal laws. Be
advised that laws vary depending on town, city, county, state, etc. Use of
certain products on public streets, roads, or highways may be in violation of
law. The Buyer is solely and exclusively legally and personally responsible
for any violation of the law by the installation or use of the product. You
must abide by all local, state, and federal laws, including but not limited to
vehicle safety, traffic laws, and ordinances. It is your responsibility to
know the laws and how they apply to you.
The Buyer is responsible for fully understanding the capability and
limitations of his/her vehicle according to manufacturer specifications,
warnings and instructions and agrees to hold SuperATV ® harmless from any
damage resulting from failure to adhere to such specifications, warnings and/
or instructions. The Buyer is also responsible to obey all applicable federal,
state, and local laws and ordinances when operating his/her vehicle while
using this product, and the Buyer agrees to hold SuperATV ® harmless from any
violation thereof.
Need help with your installation?
sales@superatv.com
1-855-743-3427
www.superatv.com
8:00am – 8:00pm EST M-Th
8:00am – 7:00pm EST Friday
9:00am – 2:00pm EST Saturday
Brake Line Clip and hardware
Read instructions and view illustrations before beginning.
Thank You For Choosing
© 2018 SuperATV.com®. All Rights Reserved.
Rev IN-AA-K-MULE-FXT-1.5-HC 5/28/2021
Documents / Resources
|
SUPERATV Front High Clearance 1 1 by 2 Inch Offset A Arms for Kawasaki Mule
FXT
[pdf] Instruction Manual
Front High Clearance 1 1 by 2 Inch Offset A Arms for Kawasaki Mule FXT, Front
High Clearance 1 1 by 2 Inch Offset A Arms, AA-K-MULE-FXT-1.5-HC
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>