SUNDRAX Wireless Splitter Pro/Pro Duo User Manual
- June 2, 2024
- SUNDRAX
Table of Contents
SUNDRAX Wireless Splitter Pro/Pro Duo
Specifications
- Supported protocols: DMX512, RDM
- DMX data refresh rate: 44 Hz
- DMX input ports: 1 or 3 isolated
- DMX output ports: 5,8 or 10 isolated
- DMX connectors: XLR (5 pins, 3 pins) or RJ-45 (etherCON)
- Mounting: Rack
- Power supply: ~100-250 VAC, 50/60 Hz
- Mains Fuse: 0.5 A
- Input power: 5 W
- Operating Temperature: -0°С… +60°С
- IP Rating: IP 20
Safe operation
- In installation, operation, preventive maintenance and repairs of the device, the requirements of the safety rules must be followed.
- To ensure safe and reliable operation of the devices, please observe the following requirements:
- Use the device only for its intended purpose
- Do not use devices that shows signs of malfunctioning
- Avoid strong physical impacts on the device
- Protect devices and cables from contact with corrosive liquids
- Whenever a fault is detected in the device, please contact the manufacturer.
Warning!
The device uses hazardous voltage AC 100-250V
General information
- Splitter Pro is a single-channel DMX512 splitter and is an effective solution for controlling dynamic lighting equipment. A feature of the splitter is the ability to transfer DMX512, RDM (ANSI E1.20) protocols from one input to 5 or 10 outputs.
- Splitter Duo Pro is a double-channel DMX512 splitter with 2 inputs and 8 outputs. Splitter Duo Pro can work as two separate splitters 1-to-4, or as a single splitter with 1 input and 10 outputs (similar to Splitter Pro).
- Splitter Pro and Splitter Duo Pro can be supplied with XLR 5-pin, XLR 3-pin, or EtherCON connectors.
- RDM support can be enabled and disabled by a stick switch on the front panel.
- Each input connector has a through-output connector to pass DMX512 signal to other devices in a chain.
- The device is designed in a housing for installation in a 19-inch rack and can be used at positive temperatures indoors.
Advantages
- Rack form factor 1U 11 cm deep with protection IP20
- Maximum surge protection – power supply optimized for voltage from 90 to 315 VAC
- Thru DMX outputs for each input
- Smart indication of operating modes
- Full RDM support (ANSI E1.20)
- Galvanic isolation on all ports
- Fastest recovery after short power failure
- PowerCON TRUE1 inlet+outlet combination
Installation
Before mounting and power up, it is necessary to verify protective earthing and cable connections.
- Ensure the device has no damage due to transportation
- Install the unit into the rack and secure it with screws. Connect the power cable plug to a power outlet
- Connect cable to input port “IN” if you use Splitter Pro device or to necessary input port (“IN COM”, “IN A” or “IN B”) if you use Splitter Duo Pro device. If the input signal is present, the appropriate port indicator lights green. If there is no signal, the indicator is red.
- Connect the desired number of output lines to the “OUT” connectors.
- The device is ready for use
Indication
Splitter Pro indicates presence of DMX512 signal on the input(s), activity in DMX universe, and the RDM E1.20 activity.
Connection scheme
Splitter Pro, Splitter Duo Pro (single input mode)
Splitter Duo Pro (double input mode)
ABOUT COMPANY
- Sundrax Electronics
- 6008, First Central 200
- 2 Lakeside Drive, Park Royal, London
- NW10 7FQ United Kingdom
- + 44 (0) 208 991 33 19
- office@sundrax.com
- www.sundrax.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>