SUNDRAX SPP-3-1D5D Splitter Pro Rack Mount DMX512 Splitter/Repeater User Manual
- June 5, 2024
- SUNDRAX
Table of Contents
User Manual
Splitter PRO
Splitter PRO DUO
SPP-3-1D5D, SPP-5-1D5D, SPP-6-1D5D,
SPP-3-1D10D, SPP-5-1D10D, SPP-6-1D10D,
SPPD-3-3D8D, SPPD-5-3D8D, SPPD-6-3D8D
Specifications
Supported protocols | DMX512, RDM |
---|---|
DMX data refresh rate | 44 Hz |
DMX input ports | 1 or 3 isolated |
DMX output ports | 5,8 or 10 isolated |
DMX connectors | XLR (5 pins, 3 pins) or RJ-45 (etherCON) |
Mounting | Rack |
Power supply | ~100-250 VAC, 50/60 Hz |
Mains Fuse | 0.5 A |
Input power | 5 W |
Operating Temperature: | -0°С… +60°С |
IP Rating | IP 20 |
Safe operation
In the installation, operation, preventive maintenance, and repairs of the
device, the requirements of the safety rules must be followed.
To ensure the safe and reliable operation of the devices, please observe the
following requirements: Use the device only for its intended purpose
Do not use devices that show signs of malfunctioning Avoid strong physical
impacts on the device Protect devices and cables from contact with corrosive
liquids
Whenever a fault is detected in the device, please contact the manufacturer.
Warning!
The device uses hazardous voltage AC 100-250V
General information
Splitter Pro is a single-channel DMX512 splitter and is an effective solution
for controlling dynamic lighting equipment. A feature of the splitter is the
ability to transfer MX512, RDM (ANSI E1.20) protocols from one input to 5 or
10 outputs.
Splitter Duo Pro is a double-channel DMX512 splitter with 2 inputs and 8
outputs. Splitter Duo Pro can work as two separate splitters 1-to-4, or as a
single splitter with 1 input and 10 outputs (similar to Splitter Pro).
Splitter Pro and Splitter Duo Pro can be supplied with XLR 5-pin, XLR 3-pin,
or EtherCON connectors. RDM support can be enabled and disabled by a stuck
switch on the front panel. Each input connector has a through-output connector
to pass the DMX512 signal to other devices in a chain. The device is designed
in housing for installation in a 19-inch rack and can be used at positive
temperatures indoors.
Advantages
Rack form factor 1U 11 cm deep with protection IP20
Maximum surge protection – power supply optimized for voltage from 90 to 315
VAC Thru DMX outputs for each input Smart indication of operating modes Full
RDM support (ANSI E1.20) Galvanic isolation on all ports
Fastest recovery after short power failure
PowerCON TRUE1 inlet+outlet combination
Installation
Before mounting and powering up, it is necessary to verify protective earthing and cable connections.
- Ensure the device has no damage due to transportation
- Install the unit into the rack and secure it with screws. Connect the power cable plug to a power outlet
- Connect the cable to input port “IN” if you use a Splitter Pro device or to the necessary input port (“IN COM”, “IN A” or “IN B”) if you use a Splitter Duo Pro device. If the input signal is present, the appropriate port indicator lights green. If there is no signal, the indicator is red.
- Connect the desired number of output lines to the “OUT” connectors.
- The device is ready for use
Indication
Splitter Pro indicates the presence of DMX512 signal on the input(s), activity in the DMX universe, and the RDM E1.20 activity.
LED | Status |
---|---|
Red | No valid DMX signal on input |
Green | A valid signal is detected, and no changes in DMX data |
Blinks green | A valid signal is detected, DMX data is being changed |
Blinks orange | RDM activity is detected |
Connection scheme
Splitter Pro, Splitter Duo Pro (single input mode)
Splitter Duo Pro (double input mode)
Technical maintenance
Maintenance of the device, search, and troubleshooting should be performed by service personnel. The device should be free from dirt, dents, and connecting cables, and wires must be intact and securely fastened.
Notes
Please send all your warranty-related questions to
support@sundrax.com
All Sunday products are covered by a 36-month warranty.
Sunday Electronics
6008, First Central 200
2 Lakeside Drive, Park Royal, London
NW10 7FQ United Kingdom
+ 44 (0) 208 991 33 19
office@sundrax.com
www.sundrax.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>