SUNDRAX PGA-0-D PowerGate Arma Device User Manual
- June 4, 2024
- SUNDRAX
Table of Contents
SUNDRAX PGA-0-D PowerGate Arma Device
Specifications
| Supported protocols | DMX512, RDM, PWR DMX |
|---|---|
| DMX data refresh rate | 44 Hz |
| DMX ports | 1, 2 or 4 isolated |
| DMX connectors | Terminal blocks 15EDGVC |
| Input Power (max) | 5 W |
| Power supply | ~100-270 V, 50/60 Hz |
| Mains fuse | 0,1 A |
| Setup | Web interface |
| Working temperatures | -40…+70°С |
| Ingress protection | IP 65 |
| Dimensions and mounting | 171 х 55 х 121 mm on surface/truss |
Safe operation
- To ensure safe and reliable operation of the devices, please observe the following requirements
- Use the device only for its intended purpose
- Do not use devices that show signs of malfunctioning
- Avoid strong physical impacts on the device
- Protect devices and cables from contact with corrosive liquids
- Whenever a fault is detected in the device, please contact the manufacturer.
**Warning!**
The device uses hazardous voltage AC 100-270V
General information
PowerGate is a series of transceivers employing existing power lines (110V/220V) to transmit DMX signal using PWRDMX technology introduced by Sundrax. PWRDMX eliminates the need of new cabling. Connected to the same power network, PowerGate devices form a network for reliable high speed communication.
Advantages
DMX512 via 220/110 V transceiver
Die-cast metal casing
No buttons
Full galvanic isolation
Up to 400 m transmission range
The devices supplied are configured as data transmitters to the 230/110V power
line (hereinafter referred to as the «transmitter») or as data receivers from
line (hereinafter referred to as the «receiver»).
Transmitter has 1, 2 or 4 input DMX ports for receiving DMX data from the
lighting desks, other converters, etc.
Upon inputting proper DMX signal the transmitter starts to send DMX data via
power line. If one or more PowerGate receivers are connected to the same power
network segment, they will receive data from power line and output these data
as DMX signal. DMX output signal from the receivers may be connected to
fixtures or other converters in a normal way.
If transmitter has 2 or 4 ports, each of these is operating independently: DMX
data from input 1 are transmitted to output 1 of all connected receivers, data
from input 2- to output 2 of all receivers, etc.
The set of PowerGate devices needed for installation is delivered pre
configured with proper number of transmitters and receivers, so customer
should only connect them to power line.
If network configuration change is needed for example, increasing the number
of receivers, switching device’s function from receiver to transmitter and
back, creating two or more separated networks in one power line, etc.,
PowerGate’s Ethernet input port is used.
PowerGate features LSA-PLUS-type connector for making temporary or permanent
connection to computer/local network. Network setup is performed via web-
interface of device, in the same way as for ArtGate devices. Please refer to
ArtGate manual.
Installation
Before mounting and power up, it is necessary to verify protective earthing and cable connections.
- Visually inspect the device to make sure that there are no transportation damages.
- Connect the first device in transmitter mode to DMX signal source, and the second device in receiver mode to DMX-controlled equipment.
- Connect AC power cable of the device to a power outlet in the network segment which is selected for work. There should be no reactive components such as transformers, surge protectors, etc. between the power sockets transmitter and receiver connected to.
Normal operation of the device in any mode starts immediately after switching power on.
Wireless network configuring (receiver)
- At power-on the receiver waits for a connection request from the transmitter. In this state the green LEDs on it lights steadily.
- When connected to the transmitter the receiver LEDs start blinking on every data reception.
DMX512 data received from network are sent to the output interface.
Wireless network configuring (transmitter)
| Fault Name, Visual Signs | Possible Reasons | Troubleshootings |
|---|---|---|
| The device does not work, neither of the LEDs are lit | There is no supply | |
| voltage Supply line fuse is broken | Connect the device to a working power |
outlet Replace the supply line fuse
No data transmission between the transmitter and one or more receivers| The
receivers are in another network segment There are reactive elements present
in the segment| Check the network, put devices to the same mains segment Check
the network, remove reactive load
Connection scheme
Technical maintenance
Maintenance, search and troubleshooting should be performed by service personnel.
The device should be free from dirt, dents, connecting cables and wires must be intact and securely fastened.
Notes
Please send all your warranty-related questions to
support@sundrax.com
All Sundrax products are covered by a 36 months warranty
Sundrax Electronics
6008, First Central 200
2 Lakeside Drive, Park Royal, London
NW10 7FQ United Kingdom
+ 44 (0) 208 991 33 19
office@sundrax.com
www.sundrax.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>