SUNDRAX DGD-1-D4DIM4AC DimGate DIN DMX AC Dimmer User Manual

June 4, 2024
SUNDRAX

User Manual
TimeGate DIN
DGD-1-D4DIM4AC

Specifications

Control interface DMX512, RDM
Number of DMX addresses 8
Controllable output lines 4 AC and 4 analog 1-10V/0-10V
Connectors Terminal blocks 2EDGVC, 15EDGVC
Input Voltage AC 90-230 V, 50 Hz
Max current per channel 230 V 10:00 AM
Maximum load power 2.4 kW per channel
Mains Fuse 0.5 A
Setup DIP switches, RDM
Operating Temperature -40…+70°C
IP Rating IP 20
Dimensions, mm 210(D) x 105(H) x 75(W)

General information

To ensure the safe and reliable operation of the devices, please observe the following requirements: Use the device only for its intended purpose Do not use devices that show signs f malfunctioning Avoid strong physical impacts on the device Protect devices and cables from contact with moisture or other corrosive liquids Whenever a fault is detected in the device, please contact the manufacturer.v

Safe operation

To ensure the safe and reliable operation of the devices, please observe the following requirements: Use the device only for its intended purpose Do not use devices that show signs of malfunctioning Avoid strong physical impacts on the device Protect devices and cables from contact with moisture or other corrosive liquids Whenever a fault is detected in the device, please contact the manufacturer.

Warning!
The device uses hazardous voltage AC 90-250V

Advantages

Dim AC lines and 1-10V/0-10V lines from one device Independent phase inputs for dimmable 230V channels  Active analog 1-10V/0-10V outputs, capable to connect up to  00 drivers/ballasts Maximum surge protection – power supply optimized for voltage from 100 to 315 V AC switcher mode Full galvanic isolation of all ports (except 1-10V)

Installation

  1.  Ensure the device has no damage caused by transportation
  2. Install the device on DIN-rail
  3.  Connect power supply according to connection scheme
  4.  Connect DMX512, AC dimming lines, 1-10 outputs according to the connection scheme
  5.  Connect the grounding circuit to the grounding clamp terminal
  6. Set DMX start address on DIP switcher section 1-9. DMX start address is set as binary code where section 1 refers to LSB and section 9- to MSB, ON position- to binary «1», OFF position- to binary «0». Valid addresses range from 1 to 504
  7.  Select the necessary AC channels mode by DIP switcher section 10. Set section 10 to OFF to select the AC dimmer function. Set section 10 to ON to select AC switcher  unction
  8. Apply a MAINS voltage to the terminal «~230V»

Warning!
Before mounting and turning on the power, you need to make sure protective ground cable connections and places of their connection

Operation

TimeGate DIN devices start their normal operation a few seconds after they have been powered up. Output channels operate according to values received from DMX512  ort. AC channel 1 corresponds to the DMX start address set by the DIP switches, AC channel 3- to start address+3. 1-10V channel 1 corresponds to start address+4, 1-10V channel 4-  o start address+7. When AC dimmer mode is selected, the actual level on  AC outputs changes proportionally to the DMX value. When AC switcher mode is selected, AC channels just switch the load ON and OFF, DMX value 0-127 switches the load off, and DMX value 128-255 switches the load ON. LED indicator shows the status of the input DMX512  signal. If the indicator is red, no DMX512 signal is detected on input. If the indicator is green, a valid DMX512 signal is received. The indicator blinks on change DMX values controlling the device’s outputs.

RDM

The device supports DMX address assignment and dimmer/switcher function changing via RDM. To select RDM address assignment mode, set all DIP-switcher sections to OFF.  n other cases the actual DMX address will be indicated in RDM parameters anyway. AC dimmer and AC switcher functions can be selected via RDM by choosing the corresponding “device personality”.

Connection scheme

SUNDRAX DGD-1-D4DIM4AC DimGate DIN DMX AC Dimmer -fig

Technical maintenance

Maintenance, search, and troubleshooting should be performed by service personnel. The device should be free from dirt, dents, and connecting cables and wires must be intact and securely fastened.

Notes ………….

Please send all your warranty-related questions to support@sundrax.com
All Sunday products are covered by a 36 month warranty.

DMX AC dimmer with four additional 0-10V/1-10V outputs DimGate DIN

Sunday Electronics
6008, First Central 200
2 Lakeside Drive, Park Royal, London
NW10 7FQ United Kingdom
+ 44 (0) 208 991 33 19
office@sundrax.com
www.sundrax.com

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals