Brydge iTrack Standalone Desktop Multi-Touch Trackpad for iPad User Manual
- June 6, 2024
- Brydge
Table of Contents
Brydge iTrack
User Manual
POWER
To power on, slide the power switch on the back of the unit from left to right and the release LED will turn green for three seconds to indicate the trackpad is on To power off, slide the power button to left and release.
PAIR
Once the trackpad is on, slide the power switch to the right (towards the LED) and hold for three seconds LED will flash blue until the trackpad is successfully paired. On your device under Bluetooth settings select Brydge Track.
CHARGE
To charge your Brydge iTrack, insert the supplied USB-C cable into the charging port. The battery is charging when the LED flashes red. The LED will turn off when the battery is fully charged
FIRMWARE
Download Brydge Connect from the App Store for the latest firmware updates
SETTINGS
AssistiveTouch settings must be off for gestures to work properly To do this, go to iPad Settings > Accessibility > Touch > AssistiveTouch > OFF
HAVE A QUESTION? Visit www.brydge.com/support
TRACKPAD GESTURES
| Open Today View
Use two fingers to swipe right
---|---
| Open the App Switcher
Swipe up with three fingers, pausing before you lift your fingers
| Go Home
Use one finger to swipe the pointer past the bottom of the screen
| Switch between open apps
Swipe left or right with three fingers
| Scroll Up or Down
Swipe two fingers up or down
| Open Control Center
Use one finger to swipe to the top right corner.
| Zoom in and out
pinch open to zoom in, or pinch closed to zoom out
| Scroll Left or Right
Swipe two-finger left or right
| Open Search
Swipe down with two fingers.
Thank you for purchasing a Brydge product. This product comes with a 1-year limited hardware warranty on the terms and conditions set out in this document and at www.brydge.com/warranty. All Brydge warranties are non-transferrable and are only available to the original end- user of the product. Warranties do not apply to products purchased from online vendors unauthorized to sell Brydge-branded products. If a defect arises during the warranty period, cease using the product and contact Brydge. To obtain warranty service, visit www.brydge.com/support or call +1 435-604-0481. Brydge, at its sole discretion and option, will (1) repair the product at no charge using new parts or parts that are equivalent to new in performance and reliability, or (2) replace or exchange the product with a product of equivalent functionality and value. Brydge offers free return shipping on any approved warranty claims. A shipping label will be provided to you if you are within the United States. If you are outside the United States, Brydge will reimburse your return shipping to a maximum of US$15.00 after providing a copy of the shipping receipt.
Australia Only: Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure.
Brydge Technologies LLC 11912 Sidewinder Dr, Suite 104, Park City, UT 84060 USA
This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science, and Economic Development Canada’s license-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device. This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, Were is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna
- Increase the separation between the equipment and receiver
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
- Consult the dealer or an experienced radio/TV technician for help.
CAUTION
DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS
The battery shall not be exposed to excessive heat such as sunshine, fire, or
the like.
© 2021 Brydge. All Rights Reserved.
iPad and Apple have registered trademarks of Apple Inc., registered in the
U.S. and other countries.
The Bluetooth word mark and logos are owned by Bluetooth SIG, Inc. Use of such marks by Brydge is under license Brydge is a trademark of Brydge Global Pte. Ltd. Other trademarks and tradenames are those of their respective owners