DINSTAR DAG1000-4S VoIP Gateway Installation Guide

June 12, 2024
DINSTAR

DINSTAR DAG1000-4S VoIP Gateway Installation Guide
DINSTAR DAG1000-4S VoIP Gateway

Number of Ports

Port TypeGateway WAN LAN FXS
DAG1000-4S 1 1 4
DAG1000-8S 1 3 8

Description of Indicators

Indicator Definition Status Description
PWR Power Indicator On The gateway is powered on
Off The gateway is powered off or there is no power supply
RUN Running Indicator Slow Flashing The gateway is running properly
Fast Flashing If there is a SIP account registered successfully, the

indicator is fast  flashing
Off| The gateway is running improperly
FXS| Telephone In-use Indicator| On| FXS port   is currently occupied by a call
Off| FXS port is idle or faulty
WAN/ LAN| Network Link Indicator| Green Flashing| The gateway is properly connected to network
Off| The gateway is not connected to network or network connection is improper way
Network Speed Indicator| On| Work at 100Mbps
Off| Work at 10Mbps

Note : DAG1000-4S has no network speed indicator.

Indicators and Ports

DAG1000-4S

Indicators and Ports

DAG1000-8S
Indicators and Ports

Installation Attentions

  • Anti-jamming: to reduce the interference with telephone calls, it’s highly recommended that telephone lines connected to the gateway should be placed away from power cables.
  • Power supply: the power adapter of the gateway accepts DC input voltage of 12V.
  • Please ensure safe and stable power supply.
  • Network bandwidth: please ensure there is enough network bandwidth so as to guarantee stabilized running of the gateway.
  • Temperature and humidity: to avoid any accident that might cause malfunction , it’s advised to install the gateway in an equipment room where temperature and humidity are appropriate.
  • Ventilation: to avoid overheating, please do not pile up the gateway with other devices and make sure the gateway has good ventilation around.
  • Mechanical load: please make sure the gateway is placed steadily to avoid damage.
  • It’s highly advised to horizontally place the gateway on a flat surface or a cabinet.

Installation Instructions

Connection Diagram for DAG1000-4S

  • Network Connection
    Installation Instructions

  • Telephone Connection
    Installation Instructions

  • Power Connection
    Installation Instructions

Connection Diagram for DAG1000-8S

  • Network Connection
    Installation Instructions

  • Telephone Connection
    Installation Instructions

  • Power Connection
    Installation Instructions

Modify PC’s IP Address

To log in the Web Management System of the gateway, you need to modify the IP address of PC first to make it at the same network segment with the gateway.

  1. On the PC, click ‘Network (or Ethernet) → Properties’.
    Modify PC’s IP Address

  2. Double-click ‘Internet Protocol Version 4 (TCP/IPv4)’.
    Modify PC’s IP Address

  3. Select ‘Use the following IP address’, and then enter an available IP address ‘192.168.11.XXX’ which is at the same network segment with ‘192.168.11.1’.
    Modify PC’s IP Address

Log in Web Management System

Open a web browser and enter the gateway’s IP address (default IP is 192.168.11.1). Then input username and password in the displayed login GUI. Both the default username and password are admin.

Modify Gateway’s IP Address

If you want to modify the IP address of DAG1000-4S/8S, please click ‘Network → Local Network’ in the navigation tree on the left of the Web  Management System, and then input new IP address and DNS server address on the displayed interface.

Configure SIP Server

Log in the Web Management System of the gateway, and then click SIP Server in the navigation tree and then enter the address of the SIP server which is to be registered. Click Save in the last.

Configure SIP Server

Click Port in the navigation tree on the left, and then click Add. Input the SIP account and authentication password assigned by the SIP server.
Configure SIP Server

Click Save and then restart the gateway for the new configurations to take effect.

Basic Operations

  • Dial *158# to query the IP address of LAN port of the gateway;
  • Dial *159# to query the IP address of WAN port of the gateway;
  • Dial *114# to query the telephone number of a FXS port;
  • Dial 165000000# to restore default IP address, username and password;
  • Restore factory default settings:
    1. dial 166000000#;
    2. press the RST button for 7 seconds;
    3. Log in the gateway and then click ‘Tools → Factory Reset’, then click Apply and restart the gateway.
  • Dial *111# to restart the gateway.

More Details

This document only provides instructions for quick installation and basic configuration, For detailed configuration and parameter explanation, please make reference to user manual or ask for online technical support.

IP Communication Solutions

Shenzhen Dinstar Co., Ltd.
Web: www.dinstar.com

Thanks for Choosing Dinstar’s VoIP Gateway!

Please read this guide carefully before installing the gateway. If you need any technical support, please contact us.
Tel: +86 755 61919966
Email: support@dinstar.com
Website: www.dinstar.com

QR Code

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals