RAB X17 XFU 3-Way Adjustable Dusk to Dawn LED Flood Light Instruction Manual

: June 4, 2024
: RAB

Table of Contents

KNUCKLE MOUNT
TRUNNION MOUNT
SLIPFITTER MOUNT
FIELD ADJUSTMENT
0-10V DIMMABLE WIRING
CLEANING & MAINTENANCE
TROUBLESHOOTING
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

RAB X17 XFU 3-Way Adjustable Dusk to Dawn LED Flood Light Instruction Manual

RAB X17 XFU 3-Way Adjustable Dusk to Dawn LED Flood Light Instruction
Manual

IMPORTANT

READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.
RAB fixtures must be wired in accordance with the National Electrical Code and all applicable local codes. Proper grounding is
required for safety. THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED.
WARNING: Make certain power is OFF before installing or maintaining fixture. No user serviceable parts inside.
WARNING: Do not use an electric generator to test LED fixtures.
WARNING: Min 75°C SUPPLY CONDUCTORS.

KNUCKLE MOUNT

To ensure weatherproof seal, apply weatherproof silicone sealant around the edge of the junction box (not supplied). This is especially important with an uneven wall surface.

Secure the fixture to a 1/2” NPS hole in the junction box or landscape post as shown in Fig. 1. Seal arm thread using Teflon® tape or silicone sealant.
Make appropriate wire connections per NEC in an approved enclosure (not included) see Fig. 7.
The Knuckle Arm allows 180° of vertical aiming adjustment depending on the mounting position as shown in Fig. 2.

RAB X17 XFU 3-Way Adjustable Dusk to Dawn LED Flood Light -
fig.1,fig.2

TRUNNION MOUNT

To adjust the angle of the Fixture using the Trunnion (Fig. 4):

Loosen the Pivot Bolts and Angle Locking Screws.
Make appropriate wire connections per NEC in an approved enclosure (not included) see Fig. 7.
Adjust fixture to desired angle.
Tighten Pivot Bolts and Angle Locking Screw.

SLIPFITTER MOUNT

Place the Slipfitter over the Tenon and secure the Fixture with the Locking Bolts (4) on the side of the Slipfitter as shown in Fig. 3.
Make appropriate wire connections per NEC in an approved enclosure (not included) see Fig. 7.
Loosen the Locking Bolts (4) and swivel Fixture to desired angle.
Tighten the Locking Bolts (4).

RAB X17 XFU 3-Way Adjustable Dusk to Dawn LED Flood Light -
fig.3

FIELD ADJUSTMENT

Follow instructions below to change fixture Power (W) or Color Temperature (CCT) from the factory settings and Photocell On/Off option.

Factory Settings: 4000K and 60W

Remove Selector Switch Caps by turning counterclockwise using a flat head screwdriver (Fig. 5).
Locate the Selector Switches on the fixture (Fig. 6).
Select Power (W) and Color Temperature (CCT) by sliding the respective switch to the desired value.
Select Photocell On/Off option by sliding respective switch to the desired value.
Replace Selector Switch Caps and tighten with a flat head screwdriver.

RAB X17 XFU 3-Way Adjustable Dusk to Dawn LED Flood Light -
fig.5,6

Note : These instructions do not cover all details or variations in equipment nor do they provide for every possible situation during installation, operation or maintenance.

0-10V DIMMABLE WIRING

Universal voltage driver permits operation at 120V thru 277V, 50 or 60 Hz. For 0-10 Dimming, follow the wiring directions as shown in Fig. 7.

Connect the black/brown fixture lead to the LINE supply lead.
Connect the white/blue fixture lead to the COMMON supply lead.
Connect the green/yellow wire from fixture to supply ground. Do NOT connect the GROUND of the dimming fixture to
the output.
Connect the purple fixture lead to the DIM V+ lead.
Connect the pink/gray fixture lead to the DIM V- lead.
Cap the yellow fixture lead, if present. Do NOT connect