SEALEY VS0045 15pc No-Spill Automotive Coolant Filling Set Instruction Manual
- June 12, 2024
- SEALEY
Table of Contents
SEALEY VS0045 15pc No-Spill Automotive Coolant Filling Set
Product Information
Product Name: 15PC NO-SPILL AUTOMOTIVE COOLANT FILLING SET
Model Number: VS0045
Safety Instructions
- Wear protective gloves and clothing
- Ensure all Health & Safety regulations are followed
- Allow engine and cooling system to cool down before opening the radiator cap
- Maintain tools in good condition and do not use if damaged
- Avoid wearing jewelry and tie back long hair
- Use approved eye protection
- Operate in a well-ventilated area and avoid breathing in exhaust fumes
- Avoid contact with hot engine parts
- Do not use the tool for any purpose other than its intended use
- Do not lay tools on the vehicle’s battery
- Account for all tools and parts used and do not leave any in the engine bay
- Keep children and unauthorized persons away from the working area
- Keep test kit parts clean and store in a safe, dry, childproof location
Product Usage Instructions
- Install the appropriate adapter and cap to the radiator or coolant tank.
- Press the funnel into the adapter. If an angled adapter and/or extension is needed, install it prior to installing the funnel.
- Slowly pour coolant into the funnel until it is approximately a third full.
- With the funnel attached, start the engine.
- Add coolant until the cooling system is full.
- If there is remaining fluid in the funnel, squeeze and hold the large radiator hose while pressing down the fluid stopper into the closed position.
- Remove the funnel and empty the remaining fluid into an appropriate container.
- Remove adapters and reinstall the cooling system cap.
Product Specifications
Model Number: VS0045
Automotive coolant filling set: No spill 15pc
Product Components
Figure | Description | Qty |
---|---|---|
A | Funnel | 1 |
B | Lid | 1 |
C | Large-cap A | 1 |
D | Medium cap B | 1 |
E | Small cap C | 1 |
F | Threaded cap D | 1 |
G | Large adapter A with gasket | 1 |
H | Medium adapter B with gaskets | 1 |
Thank you for purchasing a Sealey product. Manufactured to a high standard,
this product will, if used according to these instructions, and properly
maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE
OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND
WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE
DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE
INSTRUCTIONS SAFE FOR FUTURE USE.
SAFETY
- WARNING! Ensure all Health & Safety, local authority, and general workshop practice regulations are strictly adhered to when using product.
- WARNING! Ensure the engine and cooling system have cooled down, before opening the radiator cap.
- Maintain tools in good and clean condition for best and safest performance. DO NOT use funnel kit if damaged.
- Wear suitable clothing to avoid snagging. DO NOT wear jewellery and tie back long hair.
- Wear approved eye protection. A full range of personal safety equipment is available from your Sealey stockist.
- Operate in a well ventilated area and avoid breathing in exhaust fumes.
- Keep yourself, tools, and test equipment away from hot engine parts.
- DO NOT use this tool for any purpose other than that for which it is designed.
- Never lay tools on the vehicle’s battery. This may short the terminals together, causing harm to yourself, the tools, or the battery.
- Account for all tools and parts being used and do not leave any in the engine bay.
- Keep children and other unauthorised persons away from the working area.
- Keep test kit parts clean and keep this in a safe, dry, childproof location.
- IMPORTANT: Always refer to the vehicle manufacturer’s service instructions, or a proprietary manual to establish the current procedure and data. These instructions are provided as a guide only.
INTRODUCTION
- Unique design prevents overfilling and air bubbles by turning the rotary switch. Suitable for most vehicles with added adaptors for Ford and GM vehicles. The 5” extensions are designed for hard-to-reach filling expansion bottles. Contents – Funnel with switch, lid, caps large, medium and small, threaded cap, GM adaptor, Ford adaptor, 5” extension x2 and 45° elbow x2.
SPECIFICATION
- Model no: . ……………………………………………….. VS0045
- Automotive coolant filling set: ………………. No spill 15pc
OPERATION
- Install the appropriate adapter and cap to the radiator or coolant tank.
- Press the funnel into the adapter. If an angled adapter and/or extension is needed, it must be installed prior to installing the funnel. Slowly pour coolant into the funnel until the funnel is approximately a third full.
- With the funnel attached, start the engine.
- Add coolant until the cooling system is full.
- If fluid remains in the funnel, squeeze and hold the large radiator hose while pressing down the fluid stopper into the closed position. Remove the funnel and empty the remaining fluid into an appropriate container.
- Remove adapters and reinstall the cooling system cap.
Figure | Description | Qty |
---|---|---|
A | Funnel | 1 |
B | Lid | 1 |
C | Large-cap A | 1 |
D | Medium cap B | 1 |
E | Small cap C | 1 |
F | Threaded cap D | 1 |
G | Large adapter A with gasket | 1 |
H | Medium adapter B with gaskets | 1 |
I | Small adapter C with gasket | 1 |
J | Threaded cap adapter D with gasket for |
GM
| 1
K| Threaded cap adapter E with gasket for Ford| 1
L| Five-inch straight extension| 2
M| Forty-five degrees Elbow| 2
N| Switch|
- Parts support is available for this product. Please email sales@sealey.co.uk or telephone 01284 757500
ENVIRONMENT PROTECTION
- Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids according to local regulations.
- Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
- Important: No Liability is accepted for incorrect use of this product.
- Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim.
- Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR 01284 757500 sales@sealey.co.uk www.sealey.co.uk
Documents / Resources
|
SEALEY VS0045 15pc No-Spill Automotive Coolant Filling
Set
[pdf] Instruction Manual
VS0045, VS0045 15pc No-Spill Automotive Coolant Filling Set, 15pc No-Spill
Automotive Coolant Filling Set, No-Spill Automotive Coolant Filling Set,
Automotive Coolant Filling Set, Coolant Filling Set, Filling Set
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>