CALYPSO 34165 AnemoTracker App User Manual
- June 3, 2024
- CALYPSO
Table of Contents
CALYPSO
AnemoTracker App
User Manual
34165 AnemoTracker App
Calypso Instruments offers a free app to connect your device to your smartphone. With this app you can get a variety of values from your bluetooth anemometer. You can also save your wind meter data when tracking.
1.2 How to connect device to the app.
Once AnemoTracker is installed on your smartphone, you need to activate both
Bluetooth and GPS to start the app.
GPS:
When AnemoTracker is opened, a message like the one shown here will appear on
your screen.
If “YES” is pressed, the GPS will run whenever you start the AnemoTracker. If
not, you need to activate your device’s l
location by using its settings menu (this should appear in your device’s
owner’s manual).
Bluetooth:
Make sure Bluetooth mode is running on your device. If it is not activated,
the app will not work.
- Make the Settings menu appear by tapping on the three bars on the lefthand corner of the app (go to Settings section).
- Press on “Scan” and the application will automatically search for the closest device.
- The MAC address of the device will appear on the sceen.
- Click on the device with the MAC address that corresponds to your device and the app will automatically connect to your device (the MAC address of your device will be on the box and also on the device).
Note: The application automatically saves the device to which it has been connected so the next time you start the app, it will automatically connect to the saved device.
Main Screen
When you enter the application, the first screen to appear is the main screen.
This main screen has four modes:
Sailing, Weather Station, Golf and Ballistics.
2.1 Sailing Mode
2.1.1 Main Screen
This shows the values of the Real and Apparent wind. The external circle is
the compass, showing the north position (in degrees). The internal one is used
by the Real and Apparent wind markers (red and yellow respectively) to show
the direction of the wind (in degrees).
The wind speed is reflected in the center of it. If you hold this down, you
can switch between Real (true) and Apparent (app) wind speed.
Below this, the battery outline shows the level of battery of your anemometer.
Top and bottom markers
These show the values selected by the user. If it is long-pressed, a new
screen appears where you can select the desired data and the units in which it
is represented (like it is shown in the followiing photos).
Main Menu bottom
At the bottom of the main menu, there are four screen options you can choose
from: main screen, map with GPS, tridata, and multiple data.
2.1.2 Map with GPS Screen
This screen shows different values (which the user can select by pressing
on them for a couple seconds) and the “central clock” (which appears on main
screen too) while giving your location on Google Maps.
2.1.3 Graph Screen
This screen shows two graphs, one with Apparent Wind Speed and True Wind
Speed, and the other which shows Apparent Wind Direction and True Wind
Direction.
2.1.4 Multiple Data Screen
This section shows 6 different values which you can select by long-pressing on
them.
At the bottom of the main menu, there are four screen options you can choose from: main screen, wind line graph, wind bar graph, and multiple data.
2.2 Weather Station Mode
2.2.1 Main Screen
The main screen for the Weather Station Mode has a compasswith an arrow
showing the wind direction and 4 different values which can be changed by
long-pressing on them.
2.2.2 Wind Line Graph Screen
On this screen, you can see the wind speed (m/s) and wind direction. At the
top of the screen, there is the option to choose to see the data on the graph
from the last week, the last 24 hours, or the last 5 hours.
2.2.3 Wind Bar Graph Screen
On this screen, you can see the data of the wind speed (m/s) and the wind
direction in a bar graph (See screenshot on the right above).
2.2.4 Multidata Screen
This section shows 6 different values which you can select by long-pressing on
them.
2.3 Golf Mode
2.3.1 Main Screen
In the main screen of the Golf Mode, you can see the speed of the wind. You
can switch between meters per second or miles per hour by tapping on the
value.
A large orange arrow shows from which direction the wind is blowing.
2.4.1 Main Screen
In the main screen of the Ballistics Mode, you can see wind information
provided from your Calypso Instruments anemometer. You can switch between
different variables and units of measurement. Below this is information taken
from the web that provides weather data such as humidity and temperature.
Furthermore, at the top of the screen, you can see the wind direction on a
compass with the wind variable of your choice. It also shows the battery level
of you anemometer.
Configuration Panel
By tapping on the 3 bars on the left bottom corner of the app, the
configuration menu appears. There at the top you can see what device you are
connected to.
3.1 Connection Menu
The connection menu is where you can scan for your devices, rename your
device, get device info and upgrade the firmware for your device.
3.1.1 How to connect to your device.
- Make sure your GPS and Bluetooth are enabled on your smartphone.
- Make the Settings menu appear by tapping on the three bars on the lefthand corner of the app (go to Settings section).
- Press on “Scan” and the application will automatically search for the closest device.
- The MAC address of the device will appear on the sceen.
- Click on the device with the MAC address that corresponds to your device and the app will automatically connect to your device (the MAC address of your device will be on the box and also on the device).
Note: The application automatically saves the device to which it has been connected so the next time you start the app, it will automatically connect to the saved device.
3.1.2 How to rename your device.
Once your device is connected to the app, the serial number of the device
appears in the connection menu. By clicking on the serial number, a small box
appears where you can rename the device to your liking. The serial number can
still be found in the Device Info section.
3.1.3 How to upgrade your device’s firmware.
Click on Device info in the connection menu. If there is an update available,
an Upgrade Firmware button will appear in the righthand bottom corner as shown
in picture below.
Click on the button and in the following page, you will have the option to
Upgrade or Disconnect from your device. If you click on Upgrade, the new
firmware will download on your smartphone.
Note: UP-10 with firmware 0.77 does not need to upgrade the firmware.
3.2 Change Mode
In this section, you can choose between Sailing Mode, Weather Station Mode and
Gold Mode. See section 2 for more details.
3.3 Plot Settings
In this section, you can choose between meters per second, knots, kilometers
per hour or miles per hour for your speed unit measurements.
3.4 Tracking Menu
In the tracking menu, you can choose to track your device’s wind logs and the
logging rate of that track. The logging rate gives the options of racing (5
second intervals),
daysail (1 minute intervals), Cruising (5 minute intervals) and scientific (1
second intervals).
By toggling the button “Enable track?”, a new screen will appear with a red
plus button in the right hand corner and a list of your previous logs .
You can continue the tracking of a previous log by pressing on it or you can
press on the red plus button in the right hand corner to record a new track.
After pressing on the red plus button, a new screen appears with the option to
name your track and to put a long description. By clicking on “Create and
Init”, you start a new track and you will be returned to the main
screen.
To finish tracking, toggle the button “Enable track?” and a window will appear
asking if you want to stop tracking. Once you click yes, your track is
finished and you can see your track by toggling “Enable track?” button again.
Long-press on the track you want to see the data from. A new window appears
where you can edit the name, long description, export the file to Excel or to
Google Earth.
3.5 Wind Settings
In the Wind Settings section, you can turn on or off the damping, bow offset
and threshold alarm by toggling the buttons next to each value.
Troubleshooting
4.1 Connection issues
-
Make sure BT (Bluetooth) mode is running on your smartphone, Tablet or PC.
-
Make sure your device is properly charged.
If the device is solar-powered and has not been exposed to any source of light for an extended period of time, it might be necessary to keep it under direct sunlight for a few hours. A cloudy day will work too. -
Make sure no other device is linked to your Ultrasonic device.
Each unit can only be connected to a single device at a time. As soon as it gets disconnected, your device is ready to link to any other device with the Anemotracker app
installed. If you are trying to connect your device to a Garmin watch, make sure it’s first disconnected from the app in your phone.
For further information please contact Calypso Technical Support.
4.2 App Malfunction
If at any time the app does not start properly or shuts down, restart the app.
If the problem persists, unistall the app and reinstall it.
For further information please contact Calypso Technical Support through
info@calypsoinstruments.com or visit
www.calypsoinstruments.com.
AnemoTracker App
User manual English version 1.0
26/01/2022
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>