COLOR KINETICS AuxBox Activation Hub for Integrating Remote Dry-Contact Closure Triggering Devices Instruction Manual
- June 6, 2024
- COLOR KINETICS
Table of Contents
COLOR KINETICS AuxBox Activation Hub for Integrating Remote Dry-Contact
Closure Triggering Devices
- Must be installed by a qualified electrician in accordance with all national and local electrical and construction codes and regulations.
- Before installing this product, please visit the product page at www.colorkinetics.com for the latest version of the installation instructions. Due to continuous improvements and innovations, installation instructions may change without notice.
- Confirm all components received.
- Verify the electrical plan and all necessary surge protection requirements
- Allow space for connections
- Make sure power is OFF
- Choose power adaptor and attach to power supply
- Attach cables
- Plug power supply into power
- Turn the power ON
Optional
- Make sure power is OFF
- Remove screws and cover
- Set Show Range switch position
Switch Position
0
| ****
1
| ****
2
| ****
3
| ****
4
| ****
5
| ****
6
| ****
7
| ****
8
| ****
9
| ****
A
| ****
B
| ****
C
| ****
D
| ****
E
| ****
F
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---
1 – 8
| ****
9 – 16
| ****
17 – 24
| ****
25 – 32
| ****
33 – 40
| ****
41 – 48
| ****
49 – 56
| ****
57 – 64
| ****
65 – 72
| ****
73 – 80
| ****
81 – 88
| ****
89 – 96
| ****
97 – 104
| ****
105 – 112
| ****
113 – 120
| ****
121 – 128
Show Range
- Replace cover and secure screws
- Turn the power ON
-
Verify power is off before installing or de-installing.
-
Do not use any voltage or current the product is not rated for.
-
Do not attempt to install or use until you read and understand the
-
Do not use if the product housing or power cables are damaged.
-
Do not modify or alter the product. Doing so will void the warranty.
-
A power supply powering the AuxBox must have an output voltage of 24V DC and be a Limited Power Source (LPS)
-
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) This device may not cause harmful interference. 2) This device must accept any interference received, including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: 1) Reorient or relocate the receiving antenna. 2) Increase the separation between the equipment and the receiver. 3) Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. 4) Consult the dealer or an experienced radio / TV technician for help. -
This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
References
- Color Kinetics Official Website | Homepage
- Welcome to Inetics.com!
- Color Kinetics Official Website | Homepage
- Understanding Surge Protection For LED Lighting Systems - Knowledgebase
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>