WILTEC 61946 Automatic Pool Cleaning Robot User Manual
- June 4, 2024
- wiltec
Table of Contents
WILTEC 61946 Automatic Pool Cleaning Robot
Read and follow the operating instructions and safety information before using for the first time.
Technical changes reserved!
Due to further developments, illustrations, functioning steps, and technical
data can differ insignificantly.
Updating the documentation
If you have suggestions for improvement or have found any irregularities,
please contact us.
The information contained in this document may alter at any time without previous notice. It is prohibited to copy or spread any parts of this document in any way without prior written allowance. All rights re-served.The WilTec Wildanger Technik GmbH cannot be held accountable for any possible mistakes in this operating manual, nor in the diagrams and figures shown.Even though, the WilTec Wildanger Technik GmbH has undergone biggest possible efforts to ensure that the operating manual is complete, faultless, and up to date, mistakes cannot be entirely avoided.If you should find a mistake or wish to make a suggestion for improvement, we look forward to hearing from you.To return orders for exchange, repair, or other purposes, please use the following address. Attention! To allow for a smooth execution of your complaint or return, it is important to contact our customer service team before returning the goods.
Introduction
Thank you for purchasing this quality product. To minimise the risk of injury we urge that our clients take some basic safety precautions when using this device. Please read the operation instruc-tions carefully and make sure you have understood its content.Keep these operation instructions safe.
Safety precautions
- This device is not intended to be used by persons (or children) with reduced physical, sensory, or mental capabilities or persons not having the necessary experience or knowledge unless they are supervised by a person responsible for their safety or have previously been instructed in the use of the device.
- The floor cleaner must not be used when there are people in the pool.
- The floor cleaner must be removed from the pool after use.
- Remove the connection to the filter pump before cleaning the floor cleaner.
- Do not play with the device – risk of drowning!
- Make sure that the floor around the pool is dry – risk of slipping
Parts list
- Pedestal
- Suction manometer
- Border
- Flow rate regulator
- Main body
- Universal adaptor
- Guide wheel
- Hose weight
- Hose segments
- Membrane
Exploded view and parts list
Assembly and replacement of membranes
Note
When fixing part 2, part 1 does not need to be removed from part 3. Simply
plug part 2 onto part 1.Important note! Before the pool cleaner is connected
to the filtration system, the product must be sub-merged to avoid air suction.
The hoses must be filled with water. Adjust the flow regulator to get the best
performance from the cleaner.
Hose segment
Adjustment
Troubleshooting
| Problem | Proposal for solution |
|---|---|
| The cleaner starts and stops or does not move. | Make sure that filter is clean |
and pump is switched on.
Switch off safety suction; make sure that main drain is closed.
Make sure that vacuum plate is properly installed.
Check if cleaner and hose are free from air pockets.
Check membrane for damage or blockages.
The cleaner misses spots in the pool.| Make sure that correct amount of hose
has been installed; try adding or removing a length of tubing or two.
Make sure that all returns direct flow of water to pool floor; adjust balls or
use water distributor.
Make sure that hose is straight and not tangled.
The cleaner does not rise.| Make sure that pool water is properly balanced; a
high pH and/or lack of chlorine make walls very slippery.
Increase suction with flow regulator.
Check that float arm is in correct position. Note: Cleaner can- not climb
up in pools with sharp 90-degree angle between wall and floor.
The cleaner is taking too long to climb walls or get out of the water.| Reduce
suction power using flow control.
Adjust supplied hose weight towards cleaning head.
Presence of cleaning sticks in the cor- ners, under the ladders, under the
lights or on the steps of the pool.| Make sure that correct amount of hose has
been installed, try adding or removing a length of tubing or two.
Make sure that all returns direct flow of water to pool floor; adjust balls or
use water distributor.
Add optional hose motors and/or replace wheel deflector with a larger one.
Important notice:
The reprint or reproduction, even of excerpts, and any commercial use, even in
part, of this instruction manual require the written permission of WilTec
Wildanger Technik GmbH.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>