wiltec 30154 Engine Hoist Support Beam User Manual
- October 27, 2023
- wiltec
Table of Contents
30154 Engine Hoist Support Beam
User Manual
Illustration similar, may vary depending on model
30154 Engine Hoist Support Beam
Read and follow the operating instructions and safety information before using
for the first time.
Technical changes reserved!
Due to further developments, illustrations, functioning steps, and technical
data can differ insignificantly.
Updating the documentation
If you have suggestions for improvement or have found any irregularities,
please contact us.
The information contained in this document may alter at any time without
previous notice. It is prohibited to copy or spread any parts of this document
in any way without prior written allowance. All rights reserved.
The WilTec Wildanger Technik GmbH cannot be held accountable for any possible
mistakes in this operating manual, nor in the diagrams and figures shown.
Even though, the WilTec Wildanger Technik GmbH has undergone biggest possible
efforts to ensure that the operating manual is complete, faultless, and up to
date, mistakes cannot be entirely avoided.
If you should find a mistake or wish to make a suggestion for improvement, we
look forward to hearing from you.
Send an e-mail to: service@wiltec.info
or use our contact form:https://www.wiltec.de/contacts/
The most recent version of this manual in various languages can be found in
our online shop via: https://www.wiltec.de/docsearch
Our postal address is:
WilTec Wildanger Technik GmbH
Königsbenden 12
52249 Eschweiler
Germany
To return orders for exchange, repair, or other purposes, please use the
following address.
Attention!
To allow for a smooth execution of your complaint or return, it is important
to contact our customer service team before returning the goods.
Returns Department
WilTec Wildanger Technik GmbH
Königsbenden 28
52249 Eschweiler
E-mail: service@wiltec.info
Tel: +49 2403 55592–0
Fax: +49 2403 55592–15
Introduction
Thank you for purchasing this quality product. To minimise the risk of injury
we urge that our clients take some basic safety precautions when using this
device. Please read the operation instructions carefully and make sure you
have understood its content.
Keep these operation instructions safe.
Exploded view and parts list
| No | Name | No | Name |
|---|---|---|---|
| 1 | Support beam | 8 | Bolt M10×35 |
| 2 | Milled screw | 9 | Hexagonal nut M10/M12 |
| 3 | Washer | 10 | Trench support |
| 4 | Handle sleeve | 11 | Variable standing bracket |
| 5 | Grip handle | 12 | Rubber sleeve |
| 6 | Washer | 13 | Load hook M20×2.5 (330 mm) |
| 7 | Bolt M12×25 | 14 | Load chain |
Safety instructions
To avoid malfunctions, damage, and health impairments, observe the following instructions!
- Unqualified persons must not use the engine hoist support beam.
- Use the beam for its intended purpose, only for lifting vehicle engines. Never use the beam to transport loads!
- Make sure that the vehicle structure is suitable for the use of the beam. The surface of the vehicle structure must be flat to prevent the beam from slipping.
- Determine the most stable area of the vehicle structure to set up the beam. Do not place the supports (11) with the rubber protective caps (12) on the mudguards (paint damage!), but on the inside of the spray wall (upper mudguard attachment) or on the shock absorber receptacle.
- Make sure that the vehicle cannot roll away when using the beam.
- Do not use the beam if there is a risk of petrol or other dangerous substances leaking.
- After the beam has been properly assembled, first tighten the bolts (7) and locking knurled screws (2) to stabilise the bridge.
- Never work under a raised engine!
- Do not exceed the permissible load capacity of the beam.
- Fasten the engine to be lifted by wrapping the load chains (14) around it and hang the chains on the load hook. To lift the motor, tum the hand lever nuts (5).
- Clean and lubricate the threads on all parts from time to time.
- Store the beam in a dry place protected from moisture.
- Modifications and alterations to the beam are not permitted. We accept no liability for damage caused by improper use of the beam.
- Do not use the beam with parts being bent or damaged.
Technical specifications
| Load capacity (kg) | 500 |
|---|---|
| Chain length (cm) | approx. 90 |
| Lifting height (cm) | approx. 20 |
| Weight (without chains) (kg) | 17 |
Important notice:
The reprint or reproduction, even of excerpts, and any commercial use, even
in part, of this instruction manual require the written permission of WilTec
Wildanger Technik GmbH.
https://www.XPOtool.com
The Tool Experts
Item 30154
Documents / Resources
|
wiltec 30154 Engine Hoist Support
Beam
[pdf] User Manual
30154, Engine Hoist Support Beam, Hoist Support Beam, Engine Support Beam,
Support Beam, Beam
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>