wiltec 61479 Universal Wheel Bearing Tool Set User Manual
- October 30, 2023
- wiltec
Table of Contents
User’s manual
Universal Wheel Bearing Tool Set
61479 Illustration similar, may vary depending on model
61479 Universal Wheel Bearing Tool Set
Please read and follow the operating instructions and safety information prior
to initial operation.
Technical changes reserved!
Illustrations, functional steps, and technical data may deviate
insignificantly due to continuous further developments.
The information contained in this document may alter at any time without prior
notice. No part of this document may be copied or otherwise duplicated without
prior written consent. All rights reserved. WilTec Wildanger Technik GmbH
cannot be held liable for any possible mistakes in this operating manual, nor
in the diagrams and illustrations shown. Although WilTec Wildanger Technik
GmbH has made every possible effort to ensure that this operating manual is
complete, accurate, and up-to-date, errors cannot be ruled out entirely. If
you have found an error or wish to suggest an improvement, we look forward to
hearing from you.
Send us an e-mail to: service@wiltec.info or use
our contact form:
https://www.wiltec.de/contacts/ The most recent version of this manual in
several languages can be found in our online shop:
https://www.wiltec.de/docsearch Our postal address is: WilTec Wildanger
Technik GmbH Königsbenden 12 52249 Eschweiler Germany To return your goods for
exchange, repair, or other purposes, please use the following address.
Attention! To allow for a trouble-free complaint or return, it is important to
contact our customer service team before returning your goods.
Retourenabteilung WilTec Wildanger Technik GmbH Königsbenden 28 52249
Eschweiler Germany
E-mail: service@wiltec.info
Tel: +49 2403 55592–0
Fax: +49 2403 55592–15
Introduction
Thank you for choosing to purchase this quality product. To minimise the risk
of injury, we ask you to always take some basic safety precautions when using
this product. Please read this operating manual carefully and make sure that
you understand it.
Keep these operation instructions in a safe place.
Safety instructions
-
The wheel bearing tool may only be used for its intended purpose.
Attention! When parts to be removed are loosened, the puller might spring back with the loosened component thus representing a danger. Therefore, never stand behind the puller in the direction of a possible rebound. -
Always wear personal protective equipment.
-
Before each use of the wheel bearing tool, carry out a visual inspection to identify any damage and, if necessary, replace a damaged part.
-
Any part that might have been overloaded must be taken out of service immediately.
-
Before straining individual threads, make sure that enough thread turns are engaged.
Scope of delivery
| Name | Qty. | Name | Qty. |
|---|---|---|---|
| Adapter plate 0 5o mm | 1 | Bushing 0 83.4 mm | 1 |
| Bushing 0 55 mm | 1 | Sleeve 0 76 mm | 1 |
| Bushing 0 59 mm | 1 | Sleeve 0 86 mm | 1 |
| Bushing 0 63.3 mm | 1 | Sleeve 0 91 mm | 1 |
| Bushing 0 66.6 mm | 1 | Sleeve 0 102 mm | 1 |
| Bushing 0 70.3 mm | 1 | Disassembly screw M12x1.5 (for the disas- | |
| sembly of the wheel hub) | 3 | ||
| Bushing 0 71.5 mm | 1 | Disassembly screw Mi4x1.5 (for the disas- | |
| sembly of the wheel hub) | 3 | ||
| Bushing 0 73.-1 mm | 1 | Extracting screw 22.2 MMx300 mm | 1 |
| Bushing 0 73.4 mm | 1 | Thrust bearing | 3 |
| Bushing 0 74.8 mm | 1 | Screw-down nut SW 32 x 6o mm | 1 |
| Bushing 0 77.5 mm | 1 | Pressure sleeve 0 38 x 40 mm | 1 |
| Bushing 0 81.5 mm | 1 | Pressure sleeve 0 40 x 3 mm | 1 |
Removal
Step 1
Choose the disassembly screw depending on
the wheel bolt thread – M12×1.5 or M14×1.5 – and screw it into the thread of
the wheel hub. Attention! Two points of support on the wheel bearing housing
are not necessary. Alternating support on one side of the wheel bearing
housing can be done as described in the following:
- Turn the disassembly screw until the point of support.
- Turn the disassembly screw one more turn.
- Relieve the screw by turning it back.
- Turn the wheel hub 180° until the second screw touches the point of support.
- Proceed with the other screw in the same way as described from step 3.
Attention! Always work steadily to prevent tilting.
Step 2
Use suitable pliers to remove the retaining ring.
Step 3
Select the appropriate sleeve according to the wheel bearing housing diameter,
place it on the appropriate stepped plate, and select the appropriate bushing
depending on the bearing diameter. In the best case, the bushing is used with
the collar pointing towards the bearing for better guidance. If the collar
does not fit easily into the inner diameter of the bearing, the washer can
also be inserted with the collar pointing towards the outside.
Step 4
The individual wheel bearing tool components are now placed on the
extracting screw in the following order:
- Thrust bearing
- Pressure sleeve
- Stepped plate
- Sleeve
Extracting screw first, insert this unit into the bearing. Now place the other
side with the appropriate bushing, pressure sleeve, and screw-down nut (with
the screw-in aid first) on the extracting screw.
Attention! Check for correct fit before tightening!
Always tighten the extracting screw on the thrust bearing side and counter-
hold with a wrench on the other side.
Once the bearing has been pulled out, the complete unit can be removed from
the wheel bearing housing towards the pull-out sleeve side.
Now dismantle the tool again.
Assembly
Mount the front circlip into the
wheel bearing housing as a stop.
Position the new bearing
from behind in front of the wheel bearing housing and insert the pull-out
sleeve with the spindle into the wheel bearing housing. Attach the following
pull-out parts as described under point 4 (removal). Now the installation
process can begin. Attention! Make sure that the new bearing is positioned
correctly to avoid tilting.
After the bearing has been
pulled in, the rear assembly of the extracting screw is removed again up to
the pressure sleeve in preparation for wheel hub installation and the
extracting screw is pulled completely out of the axle beam. The wheel hub is
now pushed onto the extracting screw in front of the sleeve. Insert the
extracting screw back into the wheel bearing housing and attach the rear pull-
out parts as usual. Now the installation of the wheel hub can begin.
Attention! Ensure that the wheel hub is inserted cleanly and is not
tilted. Finally, the rear retaining ring is removed.
Adapter plate
The 50-mm plate is used to hold all bushings for use with a shop press.
Maintenance and care
The threads of the extracting screw and press-off bolts are exposed to high
strain. All threads must be clean and lubricated when used. The threads of the
extracting screw and press-off bolts should be lubricated with a heavy-duty
grease before each use.
Important
Note: Reproduction and any commercial use (of parts) of this operating
manual, requires a written permission of WilTec Wildanger Technik GmbH.
https://www.XPOtool.com
Item 61479
The Tool Experts
04 2022-1
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>