DMP LT-2363 XTLtouch LAB User Guide

DMP LT-2363 XTLtouch LAB

IDENTIFY PANEL COMPONENTS

Identify the following panel components using your panel or the on-screen photo:

• Reset button
• Programming header
• DC Power Terminals Cellular Connector
• USB Connector
• Wi-Fi Radio
• Wi-Fi LED
• 1100 Series Wireless LEDs

POWER UP THE CONTROL PANEL

1. DC power: Connect to terminals on the XTLtouch PCB
   • Transformer type: 12 VDC at 500 mA
2. USB: Connect to USB terminal on back of XTLtouch

ENTER PANEL PROGRAMMER

1. Reset the panel using the RESET BUTTON

2. Enter 6653 (PROG) at the keypad

3. Press CMD to navigate the panel Programmer menu:

   • Initialization
   • Fast Program
   • Communication
   • Network Options
   • Device Setup
   • Remote Options
   • System Reports
   • System Options
   • Bell Options
   • Output Options
   • Output Setup
   • Area Information
   • Zone Information
   • Stop
   • Set Lockout Code
     ADJUST COMMUNICATION TYPE

4. Navigate to COMMUNICATION and press a top-row select area

5. Press a top-row select area to clear the default account number

6. Enter in a new account number

7. Press CMD until COMM TYPE displays

8. Press a top-row select area to display the communication types

9. Select WI-FI

10. Press CMD to exit COMMUNICATION

ADD PANEL TO A WIRELESS NET-WORK

1. Navigate to NETWORK OPTIONS and press a top-row select area
2. LIST will show all nearby wireless network (SSID)
3. MANUAL will allow manual SSID entry

CONFIGURE SYSTEM OPTIONS

1. Navigate to SYSTEM OPTIONS and press a top-row select area
2. Press CMD to navigate to ENTRY DELAY 1
3. Press a top-row select area and choose a time from 30 to 250 seconds
4. Repeat this process for ENTRY DELAY 2
5. Press CMD to navigate to EXIT DELAY
6. Press a top-row select area and enter a time from 45 to 250 seconds
7. Press CMD to navigate to HOURS FROM GMT
8. Press a top-row select, enter in the appropriate hours from GMT for your location and press CMD
9. Using CMD, navigate to ENTER WEATHER ZIP CODE
10. Press a top-row select area and enter a LOCAL ZIP CODE to display weather alerts at the keypad

ADD A WIRELESS ZONE

1. Navigate to ZONE INFORMATION and press a top-row select area
2. Add a zone called ‘Office Door’
3. Enter a ZONE NUMBER and press CMD
4. Press a top-row select area and enter a ZONE NAME
5. Press a top-row select area and select a ZONE TYPE
6. Press a top-row select area to display a list of available areas and select the appropriate area
7. Enter an 8-DIGIT SERIAL NUMBER and press CMD to navigate to the NEXT ZONE? prompt
8. After configuring all zone settings, navigate to STOP to save changes and exit the Programmer

WIRELESS CHECK-IN TEST

1. At the keypad, enter 8144 (WALK) to enter the WALK TEST menu
2. Select WLS to begin the wireless check-in test

PIR WALK TEST

1. At the keypad, enter 8144 (WALK) to enter the WALK TEST menu
2. Select PIR to begin the PIR walk test

DIAGNOSTIC MENU

1. At the keypad, enter 2313 (DIAG) to enter the DIAGNOSTIC MENU
2. When the keypad displays CELL STATUS, press a top-row select area to begin the CELL STATUS test
3. Press CMD to navigate to CELL SIGNAL and press a top-row select area to begin the CELL SIGNAL test
4. Press CMD, select STOP to exit DIAGNOSTIC MENU

ADD A USER CODE WITH PIN

1. At the keypad, press CMD until the USER MENU?prompt displays
2. Select YES and enter 99+CMD to enter the USER MENU
3. Using CMD, navigate to USER CODES? and press a top-row select area
4. Select ADD
5. Select the USER NUMBER and press CMD
6. Enter in a 4-digit user code and press CMD
7. Press a top-row select area to add a USER NAME and press CMD
8. Press a top-row select area to select the USER LEVEL
9. Press CMD to save this user

ADD A USER CODE WITH CARD

1. At the keypad, press CMD until the USER MENU?prompt displays
2. Select YES, enter 99+CMD to enter the USER MENU
3. Using CMD, navigate to USER CODES? and press a top-row select area
4. Select ADD
5. Select the USER NUMBER and press CMD
6. Wave the card over the blue status LED
7. Press a top-row select area to add a USER NAME and press CMD
8. Press a top-row select area to select the USER LEVEL
9. Press CMD to save this user

ARM & DISARM

1. Arm the system, trip an alarm and disarm

CHANGE THE SYSTEM TYPE TO H/S/A

1. Enter the panel programmer by entering 6653 (PROG) at the keypad
2. Navigate to SYSTEM OPTIONS and press a top-row select area
3. Press a top-row select area to display the list of system types
4. Select H/S/A as the system type
5. Exit SYSTEM OPTIONS, navigate to STOP to save changes
6. Arm, disarm and trip an alarm in H/S/A system type

CHANGE THE SYSTEM TYPE TO AREA

1. Enter the panel programmer by entering 6653 (PROG) at the keypad
2. Navigate to SYSTEM OPTIONS and press a top-row select area
3. Press a top-row select area to display the list of system types
4. Select AREA as the system type

EDIT AREA NAMES

1. Press CMD to navigate to AREA INFORMATION
2. Press a top-row select area to enter AREA INFO
3. Enter an AREA NUMBER and press CMD
4. Press a top-row select area to clear any text and enter in a new area name
5. Exit AREA INFORMATION and navigate to STOP to save changes
6. Arm, disarm and trip an alarm in Area system type

ADD A Z-WAVE MODULE

1.  At the keypad, press CMD until the USER MENU?prompt displays
2. Select YES and enter 99+CMD to enter the USER MENU
3. Using CMD, navigate to Z-WAVE SETUP? and press a top-row select area
4. Select ADD
5. When the keypad displays ‘PRESS BUTTON ON Z-WAVE DEVICE’ press the button on the front of the lamp module
6. When the panel recognizes the device, it will display ‘DEVICE FOUND’
7. When the keypad displays ‘DEVICE ADDED’ press CMD
8. Press a top-row select area to name this Z-Wave device and press CMD

OPTIMIZE Z-WAVE

1. Navigate to the Z-WAVE SETUP menu and press CMD to advance the list
2. Select OPT to optimize the signal
   • After adding any Z-Wave device, it is recommended to optimize Z-Wave

CREATE A FAVORITE

1. Navigate to the Z-WAVE SETUP menu and press CMD to advance the list
2. Select FAV
3. Enter a favorite number and name
4. Choose which devices to include in the favorite

CREATE A FAVORITE SCHEDULE

1. At the keypad, press CMD until the USER MENU?prompt displays
2. Select YES and enter 99+CMD to enter the USER MENU
3. Using CMD, navigate to SCHEDULES? and press a top-row select area
4. Select FAV to create a favorite schedule
5. Enter a FAVORITE NUMBER and press CMD
6. Select a day of the week and program the ACTIVATE time
7. If this schedule will be following sunrise or sunset times, press the second select area, then choose SUNRISE or SUNSET.
   • Sunrise and Sunset times require a ZIP code to be entered in System Options
8. Continue this process for every day of the week
9. Press the BACK ARROW to exit the USER MENU

QUESTIONS

What else would you like to learn about the XTLtouch?

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>