GRACO GC2002AAIRO000 Eversure I-Size High Back Booster Seat Owner’s Manual

June 4, 2024
Graco

EverSure ™
BOOSTER
Owner’s Manual
Parts List
Fitting Guide

GRACO GC2002AAIRO000 Eversure I-Size High Back Booster Seat -
fig1GRACO
GC2002AAIRO000 Eversure I-Size High Back Booster Seat -
fig2GRACO
GC2002AAIRO000 Eversure I-Size High Back Booster Seat -
fig3GRACO
GC2002AAIRO000 Eversure I-Size High Back Booster Seat -
fig4GRACO
GC2002AAIRO000 Eversure I-Size High Back Booster Seat -
fig5

1. Head Support
2. Lower Back Support
3. Armrest
4. Base
5. Cupholders| 6. Head Support Adjustment Lever
7. Shoulder Belt Guide
8. Side Impact Shield
9. Instruction Manual Storage
---|---

IMPORTANT

READ THESE INSTRUCTIONS CAREFULLY BEFORE USE AND KEEP THEM FOR FUTURE REFERENCE.
YOUR CHILD’S SAFETY MAY BE AFFECTED IF YOU DO NOT FOLLOW THESE INSTRUCTIONS.
WARNING:
IMPORTANT, RETAIN FOR FUTURE REFERENCE: READ CAREFULLY.
NO booster can guarantee full
protection from injury in an accident.
However proper use of this booster will reduce the risk of serious injury or death to your child.
Always take care to follow the installation instructions correctly, this will ensure the booster performs at an optimum safety level.
Do take care so that the rigid items and plastic parts of a booster shall be so located and installed that they are not liable to become trapped by a moveable seat or in a door of the vehicle.
To use this booster seat according to the ECE R129/03, your child must meet the following requirements.
Child height 100cm-150cm (reference age: 3.5-12 years).
Forward facing only (in vehicle travel direction)
The booster may not fit to all vehicles for the usage from 135cm-150cm.
Any straps holding the booster to the vehicle should be tight and the straps should not be twisted.
The booster seat should be replaced if it has been subjected to heavy loads in the event of an accident or if it has been dropped.
This booster seat is only intended to be used in the car.
Do not make any alterations or additions to the booster seat without approval from the type approval authority. DO NOT remove any of the white EPP/EPS foams. Failure to do so may result in serious safety issues.
DO NOT use the seat if the surfaces are too hot from sunlight.
Never leave the child unattended in the booster seat or vehicle, not even for a few minutes.
Any luggage or other objects liable to cause injuries in the event of a collision shall be properly secured.
The booster shall not be used without the soft goods.
The booster soft goods should not be replaced with any other than the one recommended by the manufacturer, because the soft goods constitute an integral part of the restraint performance.
Always secure the child in booster, even on short trips, as this is when most accidents occur. DO NOT leave this booster or other items unbelted or unsecured in your vehicle. Remove the booster seat from the car if not regularly used and store it in a dry, unprotected surrounding.
It’s recommended not to use a second-hand booster seat whose history is not known. It may have invisible structural damages or defects due to incorrect usage/ storage.
DO NOT use any load bearing contact points other than those described in the instructions and marked on the booster.
DO NOT install this booster under the following conditions:

  1. Vehicle seats facing sideways or rearward with respect to the vehicle’s direction of travel.
  2. Vehicle seats are movable during installation.

Consult the retailer for issues concerning maintenance repair and part replacement.
To avoid burns, never put hot liquids in your booster’s cupholders.

Product Information

  1. This is an Enhanced Child Restraint System, intended to use as a Nonintegral Universal Enhanced Child Restraint System (i-Size booster seat) from 100-150cm.
  2. It is approved to the latest UN Regulation R129/03.

Product Booster seat
Materials Plastics, Metal, Fabrics
Patent No. Patents pending
Suitable for Child height 100cm150cm (Reference age 3.5-12 years).
Installation Forward facing (in vehicle travel direction)

Booster Assembly

See images 1 – 5

  1. Squeeze the head support adjustment lever first and then slide in lower back support under the fabric cover to connect them together.
    ! CHECK to make sure two pieces are securely snapped together by pulling on them.

  2. To attach the lower back support to the base, hook the lower back support over the seat bar hinge on the base.

  3. Rotate the lower back support up while holding the booster seat until it clicks into an upright position.

  4. Align the side impact shield with the slot of lower back support plastics mounts and then insert to lock. 5
    ! Please choose whether to install the side impact shield according to the size of the car.

Height Adjustment – for Head Support

See images 6
6 Squeeze the head support adjustment lever while pulling up or down on the head support until it snaps into one of the 10 positions.

Concerns on Installation

Installation with 3-point-belt

See images 10 – 16
! Pull the vehicle safety belt and
pass through the belt path, 12, and then buckle it up. 12 -3
! Position the shoulder belt through the shoulder belt guide shown in 12 -1
! DO NOT position the vehicle belt over the top of the armrests. It must pass underneath the armrests. 12 -2
! The booster can not be used if the vehicle safety belt buckle (female buckle end) is too long to anchor the booster securely. 12 -4
! After your child is placed in this booster, the safety belt must be used correctly, and ensure that any lap strap is worn low down so that the pelvis is firmly engaged. 12
! To ensure the correct head support height is obtained, the bottom of the headrest MUST be even with the top of the child’s shoulders as shown in 13 and the shoulder belt must be positioned in the green zone as shown in 14
! Place a booster firmly against the back of a forward-facing vehicle seat equipped with a lap/ shoulder belt.
! Make sure, that the shoulder belt portion of the vehicle belt goes straight through the shoulder belt guide as shown in 15
! Tighten the vehicle belt by pulling the shoulder strap until all belt slack is removed.
! If the belt lays across child’s neck, head or face, readjust the head support height.
! Any straps holding the booster to the vehicle should be tight and the straps should not be twisted.

Use Cupholders
See images 17
Detach Soft Goods

See images 18
Open 2 pairs of buttons and 6 pairs of elastics on the back of soft goods to remove it. 18
To refit, the seat pad simply reverses the steps above.

Care and Maintenance

Please wash the seat cover and inner padding with cold water under 30°C.
Do not iron the soft goods.
Do not bleach or dry clean the soft goods.

Do not use undiluted detergents, gasoline or other organic solvent to wash the child restraint. It may cause damage to the child restraint.
Do not wring out the seat cover and inner padding to dry. It may leave the seat cover and inner padding with wrinkles.
Please hang dry the seat cover and inner padding in the shade.
Please remove the child restraint from the vehicle seat if not in use for a long period of time. Put the child restraint in a cool, dry place where your child cannot access it.
Do not tamper with the harness connectors during cleaning.
Graco baby.eu 
www.Graco baby.pl

Product of: Wonder Brands Limited
FLAT/RM 1501, 15/F, Capital Centre,
151 Gloucester Road,
Wan Chai, Hong Kong
Customer Service
gracobaby.eu
www.gracobaby.pl

Documents / Resources

| GRACO GC2002AAIRO000 Eversure I-Size High Back Booster Seat [pdf] Owner's Manual
GC2002AAIRO000, Eversure I-Size High Back Booster Seat, GC2002AAIRO000 Eversure I-Size High Back Booster Seat
---|---

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals