HYPERX 676A2AA Cloud Stinger 2 Wireless User Manual
- June 10, 2024
- HYPERX
Table of Contents
USER MANUAL
HyperX Cloud Stinger 2 Wirele
Find the language and latest documentation for your HyperX Cloud Stinger 2 Wireless here.
HyperX Cloud Stinger 2 Wireless User Manual
HyperX Cloud Stinger 2 Wireless
Part Numbers
676A2AA
Overview
A. Swivel to mute microphone F. USB wireless adapter
B. Status LED G. Wireless pairing pin hole
C. Power button H. Wireless status LED
D. USB-C charge port I. USB-C charge cable
E. Volume wheel
Specifications
Headphone
Driver: Dynamic, 50mm with Neodymium magnets
Form factor: Closed Back
Frequency response: 10 Hz – 20.2 kHz
Impedance: 32 Ω
Sensitivity: 104.5 dBSPL/mW at 1 kHz
T.H.D.: ≤ 2%
Frame type: Plastic
Ear cushions: Memory foam and premium leatherette
Microphone
Element: Electret condenser microphone
Polar pattern: Bi-directional, Noise-cancelling
Frequency response: 20 Hz – 6.68 kHz
Sensitivity: -12 dBFS/Pa at 1kHz
Connections and Features
Audio connection: Wireless USB
USB audio format: Stereo
USB specification: USB 2.0
Sampling rates: 48 kHz
Bit-Depth: 16 bit
Included virtual surround sound: DTS Headphone:X
Audio controls: Onboard audio controls
Battery
Type: Rechargeable lithium-polymer
Battery life: 20 Hours*
Charge time: 3.5 hours
Wireless
Type: 2.4GHz
Wireless range: Up to 20 meters**
Physical
Weight: 275g
Cable length(s) and type(s): 0.5m USB charge cable
*Tested at 50% headphone volume. Battery life varies based on volume and usage.
**Wireless range may vary due to environmental conditions.
Charging the Headset
It is recommended to fully charge your headset before first use.
When charging the headset, the headset status LED will indicate the current
charge status.
Charge Status
| Status LED
---|---
Fully charged|
Solid green
10% – 99% battery level
| Breathing green
< 10% battery level|
Breathing red
To charge the headset, plug the headset to a USB port with the USB-C charge cable.
Setting up with PC
1. Connect the wireless adapter to the PC.
2. Power on the headset.
3. Right click speaker icon > Select Open Sound settings > Select Sound
Control Panel
4. Under the Playback tab, click on “HyperX Cloud Stinger 2 Wireless” and click on the Set Default button.
5. Under the Recording tab, click on “HyperX Cloud Stinger 2 Wireless” and click on the Set Default button.
6. Under the Playback tab, verify that “HyperX Cloud Stinger 2 Wireless” is set as Default Device and Default Communication Device. Under the Recording tab, verify that “HyperX Cloud Stinger 2 Wireless” is set as Default Device.
7. To set up DTS Headphone:X, please download the HyperX NGENUITY software at hyperx.com/ngenuity and follow the instructions in the app to install the required drivers. DTS Spatial Audio is controlled within NGENUITY software.
Setting up with PlayStation 4
- Connect the wireless adapter to the PlayStation 4 console.
- Set Input Device to USB Headset (HyperX Cloud Stinger 2 Wireless).
- Set Output Device to USB Headset (HyperX Cloud Stinger 2 Wireless).
- Set Output to Headphones to All Audio.
- Set Volume Control (Headphones) to maximum.
Setting up with PlayStation 5
1. Connect the wireless adapter to the PlayStation 5 console.
2. Go to the home page and select Settings > Sound
3. Under Microphone , set the following:
- Input Device: USB Headset (HyperX Cloud Stinger 2 Wireless)
4. Under Audio Output, set the following:
- Output Device: USB Headset (HyperX Cloud Stinger 2 Wireless)
- Output to Headphones: All Audio
5. Under Volume , set Headphones slider to maximum level.
Controls
- Status LED
- Power button
Status LED
Status
| Battery Level| LED
---|---|---
Searching| –|
Slow breathing green
**Connected***
| 90% – 100%| Solid green for 5s
10% – 90%|
Blinking green for 10s
< 10%
|
Blinking red for 10s
Battery level indication
The status LED will automatically turn off to conserve battery life
Power Button
- Hold for 3 seconds to power headset on/off
Swivel to Mute Microphone
- Swivel up to mute microphone
- Swivel down to unmute microphone
- Volume wheel
Volume Wheel
- Scroll up and down to adjust volume level
WARNING: Permanent hearing damage can occur if a headset is used at high volumes for extended periods of time
Tone Notifications
| Headset status | Tone Notification |
|---|---|
| Power On | 1 tone (mid) |
| Power Off | 2 tones (high, low) |
| Maximum volume reached | 3 tones (high) |
| Minimum volume reached | 3 tones (low) |
| Low battery (10%) | 4 tones (mid, low, mid, low) |
| Microphone muted | 2 tones (high, high) |
| Microphone active | 1 tone (high) |
| Mic monitoring on/off | 2 tones (mid, mid) |
HyperX NGENUITY Software
Go to hyperx.com/ngenuity to download the NGENUITY software. Software features include:
- DTS Headpone:X
- Adjustable EQ settings
- Adjustable auto shut-off behavior
- Battery level indicator
Manually Pairing the Headset and Wireless Adapter
The headset and wireless adapter are automatically paired together out of the box. But if manual pairing is needed, follow the steps below to pair the headset and wireless adapter.
1. While the headset is off, hold the power button until the headset status LED starts blinking red/green rapidly.
2. While the wireless adapter is plugged in, use a small tool (e.g. paper clip, SIM tray ejector, etc.) to press the button inside the pin hole until the adapter LED starts blinking rapidly.
3. Wait until both the headset LED and the USB adapter LED are solid. The headset and wireless adapter are now paired together.
Questions or Setup Issues?
Contact the HyperX support team at: hyperx.com/support
Document No. 676A2AA.A01 HyperX Cloud Stinger 2 Wireless
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>