muse M-1850 SBT TV Sound Bar with Wireless Subwoofer User Manual

: June 4, 2024
: muse

Table of Contents

LOCATION OF CONTROLS
Remote control
Installing Battery
ACCESSORIES
POWER SUPPLY
CONNECTING WITH SUBWOOFER
BLUETOOTH FUNCTION
CONNECTING WITH EXTERNAL DEVICES
TECHNICAL SPECIFICATION
SAFETY INSTRUCTIONS
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

M-1850 SBT TV Sound Bar with Wireless Subwoofer
User Manual

SOUNDBAR WITH WIRELESS SUBWOOFER

LOCATION OF CONTROLS

Main unit & subwoofer

**** : To turn the unit on/off
: To select desired function mode: BT, AUX, ARC, OPT, or USB; Long press to connect or disconnect the subwoofer
Volume – : To decrease volume
Volume + : To increase the volume
Speakers
LED display
Remote sensor
Wall Mounting brackets
AC socket ( ∼ AC IN)
AUX IN jack (LINE/ AUX)
Optical in jack (OPT)
USB port allowing MP3 playback
HDMI ARC input jack (ARC)
PAIR: To connect or disconnect the subwoofer
Pair indicator
AC socket ( ∼ AC IN)

Remote control

R1. : To turn the unit on/off
R2. : To mute or restore sound
R3. : To skip to the previous track
R4. : To skip to the next track
R5. Volume : To adjust the volume level
R6. : Play/ pause; Long press to disconnect or reconnect the current Bluetooth device
R7. : To select desired function mode: BT, AUX, ARC, OPT or USB. Long press to connect or disconnect the subwoofer
R8. ** (Bluetooth): To switch to Bluetooth mode directly
R9. EQ : To select desired sound effects: music, movie, TV
R10. TREBLE: Press the TR E BLE button first, then press the button to adjust the treble level
R11. BASS: Press the BASS** button first, then press button to adjust the bass level

Installing Battery

Insert 2 “AAA/ UM4” batteries to the remote control prior to use. Make sure to match their polarities (+/-) to the markings inside the compartment.
Before throwing any batteries away, consult your distributor who may be able to take them back for specific recycling.
NOTES:
– Never recharge the batteries, apply heat to them or take them apart.
– If the remote control is not going to be used for a long time, remove the battery to avoid damage caused by battery leakage corrosion.
– Attention should be drawn to the environmental aspects of battery disposal.
– Do not throw batteries on fire!
– Battery shall not be exposed to excessive heat such as sunshine, fire, or the like.
CAUTION: Danger of explosion if the battery is incorrectly replaced. Replace only with the same or equivalent type.

ACCESSORIES

Remote control x1
AC power cord x2
Aux in cable x1
Wall plug & screw x2 (for wall mounting use)

WALL MOUNTING INSTRUCTION

Drill 2 holes (diameter 6mm) with a spacing of 600mm on the wall.
Insert the wall plug (supplied) into the hole until it is flush with the wall surface.
Insert the screw (supplied) into the wall plug and tighten the screw approx. 4mm away from the wall.
Hang the unit to the screws as indicated below. Make sure it’s firm and stable.

Notes:

Before you drill, make sure that there are no hidden pipes or wires, or hazards behind the wall in your chosen mounting location. If you are not sure about this, perhaps you should consider having the unit mounted by someone with the necessary experience.
Check the wall strength before mounting the unit to the wall. If this is not clear, then consult relevant qualified personnel.

POWER SUPPLY

This set operates on AC 100-240V 50/60Hz. Connect the detachable power cord (included) to the AC socket on the main unit and subwoofer respectively. Insert the plug of the power cord into a convenient standard AC wall outlet.
In a concern of saving energy, when playback has reached to the end or listening volume is set at a very low level and no control is operated on the device for a period of 15 minutes, the unit will automatically switch to Standby mode.
TURNING UNIT ON/OFF
Press the button to turn on the unit. Press this button again to turn off the unit.
SELECTING FUNCTION
The function (BT/ AUX/ ARC/ OPT/ USB) is selected by pressing button repeatedly.

Notes:
– Once insert the USB device to the USB port of the unit, it will switch to USB mode automatically.
– USB mode can be selected by button only when the USB device is connected to the unit.

CONNECTING WITH SUBWOOFER

Connect the power cords of the main unit and subwoofer to the main socket outlet. When the unit is turned on, the subwoofer will pair with the unit automatically.
Disconnecting or reconnecting the subwoofer To disconnect the subwoofer from the main unit, press and hold the PAIR button on the subwoofer for 2 seconds until the pair indicator blinks blue and red rapidly. To reconnect the subwoofer to the main unit, press the PAIR button once, wait for 7 seconds, then the subwoofer will reconnect with the main unit. Or, press and hold on the main unit or remote control to disconnect or reconnect the subwoofer.
Observe the pair indicator color for the subwoofer condition:
– Standby mode: Pair indicator stays lit in red color
– Pairing successful: Pair indicator stays lit in blue color
– Pairing not successful OR disconnected from the main unit: Pair indicator blinks blue and red rapidly
Note: In case the subwoofer cannot pair with the main unit successfully, unplug the power cords of the main unit and subwoofer from the mains socket outlet. Wait for about 20 seconds and reconnect the power cords to the main socket outlet again.

BLUETOOTH FUNCTION

The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by New One S.A.S is under license. Other trademarks and trade names are those of their respective owners.
Pairing a Bluetooth Device

When the unit is ON, press button repeatedly to select Bluetooth mode. ” ” will blink slowly indicating it’s in pairing mode.
On the Bluetooth device, enable Bluetooth and select “MUSE M-1850 SBT” from the Device List. (Refer to the user manual of the device to be connected for detailed operations.) If the Bluetooth device prompts for a passcode, use “0000”. Some Bluetooth devices will ask you to accept the connection. You will hear an indication sound when pairing is successful.

Tip: If you want to connect your Bluetooth speaker to another Bluetooth audio device, press ****and hold the button to disconnect the current device, and then follow the steps above to make a new connection.

On some devices such as computers, once paired you must select the unit from the Bluetooth menu and choose “Use as Audio Device (stereo)” or similar.
Pairing remains intact when the unit and/ or your Bluetooth device is taken out of communication range. An active connection will be re-established when your Bluetooth device returns within range.
When the unit is turned on again, it will automatically try to reconnect with the most recently paired Bluetooth device.

Using a Bluetooth Device

With a unit paired (see the previous section), operate your Bluetooth device and its sound will be heard through the M-1850 SBT’s speakers.
Press ****the button on the remote control to pause playback. Press again to resume playback.
Select desired track with / on the remote control.
Adjust the volume using the Volume buttons. You can also adjust the volume on the device to which you are paired.

Hereby, NEW ONE S.A.S, declares that this MUSE M-1850 SBT is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. The declaration of conformity may be consulted at www.muse- europe.com

USB PLAYBACK

Connect a USB device to the USB port on the unit. It will switch to USB mode and start playback automatically.
Select desired track with / on remote control.

Notes:
– USB mode can be selected by button only when the USB device is connected to the unit.
– The total number of MP3 files on the USB device should not exceed 999.
– The device may not contain more than 99 directories.
– The reading time takes about a few seconds or more depending on the amount of MP3 files and folders on the USB device.
– Do not put anything other than a USB device to the port of this unit. Other objects may damage the USB mechanism.
– The USB socket must not be connected to the computer directly, for that may damage the unit.
– There are many USB devices in the market. We cannot guarantee to support all different models. Please try another USB device if your device is not supported.

CONNECTING WITH EXTERNAL DEVICES

To AUX IN jack

Plug one end (3.5mm jack) of the auxiliary cable into the LINE/AUX jack on the unit and the other end of the cable into the L/R audio jacks on the external device.
Press button repeatedly to select AUX mode. The display will show “ “.
Start playback from your auxiliary source.
Adjust the volume to the desired level.
To stop playback, disconnect your auxiliary source from the LINE/AUX jack.

Note: Remove the auxiliary cable from the LINE/AUX jack when finished listening. Don’t forget to switch off the power on your external device as well.
To OPTICAL IN jack
Connect your audio source to the OPT jack on the unit with a digital optical audio cable (cable not included)

1. Press button repeatedly to select OPT mode. The display will show “ “.
2. Start playback from your audio source.
3. Adjust the volume to the desired level.
4. To stop playback, disconnect your audio source from this unit.

Note: OPTICAL IN is for PCM format only.
To HDMI ARC in jack
The high-definition sound can be transferred from the TV to the soundbar. Use the HDMI cable (not included ) to connect the sound bar to the external TV which has an HDMI output jack. Press repeatedly to select ARC mode. The display will show ” “. Then enable HDMI output signal on your TV.
Note: HDMI ARC function needs an HDMI ARC jack on your TV. If your TV does not have an HDMI ARC jack, you can connect your soundbar with an optical jack or Aux-in jack.

TECHNICAL SPECIFICATION

POWER SUPPLY:
Main unit: AC 100-240V 50/60Hz 60W consumption
Subwoofer: AC 100-240V 50/60Hz 90W consumption
BLUETOOTH
Bluetooth Version: V5.0
Bluetooth: 2.402-2.480GHz RF
Output Power: 2.28 dBm
Working Distance: Up to 10 meters measured in open space (wall and structures may affect the range of the device)
Remote working distance: Up to 8 meters, +/- 30 degree
Specifications are subject to change without notice.

SAFETY INSTRUCTIONS

CAUTION: To reduce the risk of electric shock, do not remove the cover (or back). There are no user-serviceable parts inside the unit. Refer all servicing to qualified personnel.
The lightning flash with an arrowhead symbol within the triangle is a warning sign alerting the user of “dangerous voltage” inside the unit.
The exclamation point within the triangle is a warning sign alerting the user of important instructions accompanying the product.
WARNING: TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
The Caution mark is located at the back of the device.
IMPORTANT! – The marking plate is located at the back of the device.
– The ventilation should not be impeded by covering the ventilation openings with items such as newspapers, tablecloths, curtains, etc.
– No naked flame sources, such as lighted candles, should be placed on the apparatus.
– The use of apparatus in moderate climates.
– The apparatus should not be exposed to dripping or splashing.
– Ensure a minimum distance of 5cm around the apparatus for sufficient ventilation.
– Do not place objects filled with liquids, such as vases, on the apparatus.
– The mains plug is used as the disconnect device and it shall remain readily operable. To be completely disconnected from the power input, the main plug of the apparatus shall be disconnected from the mains completely. The main plug should not be obstructed or should be easily accessed during intended use.
– Under the influence of electrical fast transient or/and electrostatic phenomenon, the product may malfunction and require the user to power reset.
– The normal function of the product may be disturbed by strong ElectroMagnetic Interference. If so, simply reset the product to resume normal operation by following the instruction manual. In case the function could not resume, please use the product in another location.
If at any time in the future you should need to dispose of this product please note that Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or retailer for recycling advice. (Waste Electrical and Electronic Equipment Directive)