audio-technica ATM75 Cardioid Condenser Headword Microphones User Manual
- June 6, 2024
- Audio-Technica
Table of Contents
audio-technica ATM75 Cardioid Condenser Headword Microphones
Thank you for purchasing this product. Before using the product, read through
the user
manual to ensure that you will use the product correctly.
Please keep this manual for future reference.
Features
- Ideal for drummers, keyboard players, guitarists or anyone requiring hands-free operation
- Low-visibilty headband provides stable, comfortable fit
- Pivot-mounted flexible mic boom descends from left or right side
- Belt-mounted power module operates on battery or phantom power
- Cardioid polar pattern improving isolation of desired sound source
- Rugged design and construction for reliable performance
- ATM75 wired version’s power module (AT8531) includes a switchable 80 Hz high-pass filter minimizes pickup of undesired low-frequency sounds
- Wireless version equipped with cW-style locking or cH-style screw-down 4-pin termination for Audio-Technica wireless systems
Notes on use
ATM75 wired version includes a power module AT8531 that requires 11V to 52V DC
phantom power, or a 1.5V AA battery for operation. A battery need not be in
place for phantom power operation. The output of the power module is a 3-pin
XLRM-type connector.
An integral 80Hz high-pass filter provides easy switching from a flat
frequency response to a low-end roll-off. The roll-off position reduces the
pickup of low-frequency ambient noise (such as traffic, air-handling systems,
etc.), room reverberation and mechanically coupled vibrations.
ATM75cW and ATM75cH wireless versions do not contain power module and includes
clothing clip and metal-frame pop filter only. 1.4 m cable terminated with
locking 4-pin connector. The connector is also compatible with Audio-Technica
cW and cH type body-pack transmitters.
Avoid leaving the microphone in the open sun or in areas where temperatures
exceed 43°C for extended periods. Extremely high humidity should also be
avoided.
Safety precaution
Although this product was designed to be used safely, failing to use it
correctly may result in an accident. To ensure safety, observe all warnings
and cautions while using the product.
Cautions for the product
- Do not subject the product to strong impact to avoid malfunction.
- Do not disassemble, modify or attempt to repair the product.
- Do not handle the product with wet hands to avoid electric shock or injury.
- Do not store the product under direct sunlight, near heating devices or in a hot, humid or dusty place.
Connection procedure
Connect the output terminals of AT8531 power module to a device that has a microphone input (balanced input) compatible with a phantom power supply. The output connector is an XLRM-type with polarity as shown in the figure below.
Specifications
1 Pascal = 10 dynes/cm2 = 10 microbars = 94 dB SPL
Typical, A-weighted, using Audio Precision System One.
For product improvement, the product is sublect to modification without
notice.
Polar pattern
Frequency response
Cable Terminations
ATM75cW – Terminated with locking 4-pin connector for use with A-T UniPak® body-pack transmitters
Pin 1 | Pin 2 | Pin 3 | Pin 4 | |
---|---|---|---|---|
Function | Ground / Shield | Instrument | Mic Audio | Blas + In |
Wire Colour | Copper Wire | Jumper to Pin 1 | Yellow | Red |
ATM75cH – Terminated with locking 4-pin connector for use with A-T cH body- pack transmitters
Pin 1 | Pin 2 | Pin 3 | Pin 4 | |
---|---|---|---|---|
Function | Ground / Shield | Instrument | Mic Audio | Blas + In |
Wire Colour | Copper Wire | Jumper to Pin 1 | Yellow | Red |
Audio-Technica Corporation
2-46-1 Nishi-naruse, Machida, Tokyo 194-8666, Japan
©2017 Audio-Technica Corporation
Global Support Contact: www.at-globalsupport.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>