dji Mini 3 Fly More Combo Plus Kit User Guide

dji Mini 3 Fly More Combo Plus Kit

Carefully read this entire document and all safe and lawful practices provided before use.

DJITM Mini 3 Pro Two-Way Charging Hub (Figure A)

1. Status LEDs: The status LEDs display battery levels for three seconds after the batteries are inserted into the charging hub. The LEDs in an array blink successively during charging and change to solid green after the corresponding battery is fully charged.
2. Function Button: Press to check the battery power level. When both the Intelligent Flight Battery and an external device are connected for charging, the battery will be charged before the external device. Press and hold the function button for two seconds to switch the charging priority.
   • Place the charging hub on a flat and stable surface when in use. Make sure the device is properly insulated to prevent fire hazards.
   • DO NOT attempt to touch the metal terminals on the hub. Clean the metal terminals with a clean, dry cloth if there is any noticeable buildup.

Visit https://www.dji.com/mini-3-pro/downloads or https://www.dji.com/mini-3/downloads to refer to the user manual for more information.

Specifications

• Model Number CHX162-30
• Supported Charger USB Power Delivery charger
• Input (USB-C) 5 V 3 A, 9 V 3 A, 12 V 3 A
• Output (USB) 5 V 2 A
• Operating Temperature 5° to 40° C (41° to 104° F)

DJI Mini 3 Propellers (Figure B)

• Mount the marked propellers to the marked motors and the unmarked propellers to the unmarked motors.
• Use the screwdriver provided in the aircraft package to remove and install the screws. Unsuitable screwdrivers may damage the screws.
• Use the new screws provided with the propellers when installing. DO NOT reuse old screws.
• Use two propellers from the same package. DO NOT mix with propellers from other packages.

DJI Mini 3 Pro Intelligent Flight Battery

Specifications

• Model Number BWX162-2453-7.38
• Capacity 2453 mAh
• Charging Temperature 5° to 40° C (41° to 104° F)

Compliance Information

FCC Compliance Statement: Supplier’s Declaration of Conformity

Product name: DJI Mini 3 Pro Two-Way Charging Hub
Model Number: CHX162-30
Responsible Party: DJI Technology, Inc.
Responsible Party Address: 201 S. Victory Blvd., Burbank, CA 91502
Website: www.dji.com

We, DJI Technology, Inc., being the responsible party, declares that the above mentioned model was tested to demonstrate complying with all applicable FCC rules and regulations. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
CAN ICES-003 (B) / NMB-003(B)

Compliance Statement: SZ DJI TECHNOLOGY CO., LTD. hereby declares that this device (CHX162-30) is in compliance with the essential requirements and other relevant provisions of the Directive 2014/30/EU.
A copy of the EU Declaration of Conformity is available online at www.dji.com /euro-compliance
EU contact address: DJI GmbH, Industriestrasse 12, 97618, Niederlauer, Germany

Compliance Statement: SZ DJI TECHNOLOGY CO., LTD. hereby declares that this device (CHX162-30) is in compliance with the essential requirements and other relevant provisions of Electromagnetic Compatibility Regulations 2016.
A copy of the GB Declaration of Conformity is available online at www.dji.com /euro-compliance

Environmentally friendly disposal
Old electrical appliances must not be disposed of together with the residual waste, but have to be disposed of separately. The disposal at the communal collecting point via private persons is for free. The owner of old appliances is responsible to bring the appliances to these collecting
points or to similar collection points. With this little personal effort, you contribute to recycle
valuable raw materials and the treatment of toxic substances.

Compliance Statement: SZ DJI TECHNOLOGY CO.,LTD. hereby declares that this device (BWX162-2453-7.38) is in compliance with the essential requirements and other relevant provisions of the Directive 2006/66/EC,2014/30/EU
A copy of the EU Declaration of Conformity is available online at www.dji.com /euro-compliance EU contact address: DJI GmbH, Industriestrasse 12, 97618, Niederlauer, Germany

Compliance Statement: SZ DJI TECHNOLOGY CO., LTD. hereby declares that this device (BWX162-2453-7.38) is in compliance with the essential requirements and other relevant provisions of The Batteries and Accumulators (Placing on the Market) Regulations 2008 (as amended) and the Waste Batteries and Accumulators Regulations 2009 (as amended)
A copy of the GB Declaration of Conformity is available online at www.dji.com /euro-compliance.

WE ARE HERE FOR YOU

Contact
DJI SUPPORT

This content is subject to change.
Download the latest version from https://www.dji.com/mini-3is a trademark of DJI.
USB-C is a registered trademark of USB Implementers Forum. Copyright © 2022 DJI All Rights Reserved.

YCBZSS00226502

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>