ZIDOO Z20 PRO User Manual
- June 13, 2024
- Zidoo
Table of Contents
ZIDOO Z20 PRO User Manual
Introduction to Hardware of 220 PRO
Device Interface
Zidoo Z20 PRO is equipped with audio and video input & output ports and data transmission ports. Please refer to the descriptions in this manual.
-
Front
-
Right
-
Back
Instruction to installation of the antenna: Please insert the two antennas in the parcel into the antenna ports in the above diagram.
Note :
- Please load/change the hard disk after turning off the power. If it is a brand-new hard disk, Please load it after formatting it.
- Please prevent the orifice of the cooling fan from being blocked.
- Do not touch any liquid in case the liquid runs into the inner part of the device and damage it.
- Any maintenance personnel who are not appointed are not allowed to open the case.
Load the Hard Disk
Z20 PRO is equipped with 3.5 inches HDD Bay and high speed SATA transmission
port. The hard disk can be loaded by pushing with hand.
(The maximum hard disk supports 14 TB )
Note: Do not load or change the hard disk while the power is on to avoid damage of the device or hard drive data. If it is a brand-new hard disk, please format it before loading it to the device. This device supports hard disk of the following formats: EXT3, EXT4, NTFS, FAT32, EXFA
Device Connection
Connect HDMI Cable to TV
-
Cut off the power. Please make sure the power of the TV and media player are off.
-
When the TV is turned off, please connect HDMI OUT port on Zidoo to HDMI IN port on TV.
-
Connect with the power. This device is equipped with suitable DC power adapter. Please connect the head of DC power adapter to the DC power input port of this device, then insert the plug of DC power adapter into the socket of 11 0V – 240V.
-
Corresponding video source is selected by TV.
Connect AV Cable to the TV
The connection method is same as connecting HDMI cable.
Assembly Sequence to Connect RS232 to 3.5mm
Connector
Z20 PRO Specification
Front Display | LED |
---|---|
Shell | Aluminum Alloy |
OS | CPU Rea Itek RTDl 6 l 9BPD |
GPU | ARM Mali-G57 |
NPU | l .6TOPS |
RAM | 4GB DDR4 |
Internal Storage | 32GBeMMC |
Bluetooth | BT 5.2 |
WIFI | 2.4G + 5G dual-band WiFi, 802.11 a/b/g/n/ac/ax |
2T2R, 802.11 ax MIMO OFDM
Ethernet| 1 RJ-45 Ethernet Jack (10/100/1 000Mbps
HDMI Out| HDMI 2.1, support up to 4K @ 60p, HDR, 12Bit, YCbCr 4:4:4
color range, support audio pass-through
Video Decoding| 4K@60p,AV1/HEVC/H.265, 12Bit, HDRl 0, HDRlO+, Dolby
vision
Audio Decoding| Support high-definition audio pass-through and audio
decode
Intelligent Control| Mobile APP control, RS-232, TCP/IP control and
WOL support
SATA| lHDD B
USB| 1 USB 3.0, 2USB 2.0
Power Supply| DC 12V 2A
Other interface| 1 IR Receiver, 1 RCA Cvbs 1 RCA Audio L/R
Channels, 1 Coaxial/1 SPDIF(2CH, 5.1 CH), 1 3.5 (mm) RS-232, 2*External
High-Gain Antenna
Boot Initialization Wizard
Before using the machine formally, the system will perform the initial setup. Please set according to devices and requirements to get the best visual experience.
System language selection, screen zoom, time zone setting
Choose the system language according to your language habit.
Press the UP and DOWN buttons on remote control to adjust screen display area.
Select the time zone for the system according to your location.
Network Setting
Configure network to connect device with network quickly.
WIFI: choose network SSID, input password and connect WIFI.
Ethernet: plug in the network cable to connect the network automatically
Select output mode
Please select the corresponding mode according to your needs, then it will finish relevant setting.
Wizard mode : select the corresponding option according to your usage environment and device connection.
Expert mode : The audio and video output is customized by users, it is recommended for professionals.
The key definition
Define the corresponding functions for number keys, timing key, subtitle key, audio key, up and down keys and page keys on the remote control according to your usage habits.
After completing settings above, please follow prompts and click “Next” until entering Zidoo user interface. Enjoy Zidoo audiovisual feast!
OTA System Update
Zidoo will update the firmware from time to time.
Find the update icon in APPs and click it, online update and local update are
supported. After ticking “Automatically check online upgrade”, you will
receive the prompt for the latest firmware update automatically.
Online Update
Click “Online Update” to obtain information of online update.
Local Update
Users can download the update files on the forum or official website and
update firmware through files.
Copy the downloaded update file to USB disk. Click “USB update” to select the
update file.
Download the update file by online update or local update. Click “Update” to update it.
The system will automatically check the update file whether is completed or not.
Note: Automatically access to system upgrade. Please don’t power off in the progress.
Once the update process is completed, the system will automatically restart.
Special Note:
To guarantee user experience, Zidoo will update the firmware from time to
time. Therefore, this manual may not be totally in line with the product.
@ zidootv
@ zidootv
Official website: www.zidoo.tv
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>