HYPERLITE WALL.E Series LED Wall Pack Light User Manual
- June 3, 2024
- HYPERLITE
Table of Contents
- WALL.E Series LED Wall Pack Light
- FEATURES & SPECIFICATIONS
- PACKAGING INFORMATION
- FULL CUT-OFF DISTRIBUTION
- INSTALLATION INSTRUCTIONS
- APPLICATION
- CERTIFICATE OF COMPLIANCE
- READ THOROUGHLY BEFORE INSTALLATION
- FOOTCANDLE LIGHT GUIDE
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
WALL.E Series LED Wall Pack Light
User Manual
HYPERU’TE
www.hi-hyperlite.com
WALL.E Series LED Wall Pack Light
LED WALL PACK LIGHT WALL.E Series
FEATURES & SPECIFICATIONS
APPLICATION
Ideal for building, loading bay, commercial entryways, and more outdoor areas.
PACKAGING INFORMATION
FULL CUT-OFF DISTRIBUTION
INSTALLATION INSTRUCTIONS
APPLICATION
LED Wall Pack Light
(WALL.E Series)
Features
UL&CUL No E483348 Suitable for Wet Locations. 
ATTENTION BEFORE YOU INSTALL
Read these instructions completely and carefully.
WARNING
RISK OF ELECTRIC SHOCK
- Turn power on before Inspection, installation or removal.
- NOPetty ground electrical enclosure.
- Follow all NEC and local codes.
- Use only UL or IEC approved wire for input/output connections.
Save These Instructions
Use only m the manner Intended by the manufacturer. If you have any questions,
contact the manufacturer.
Prepare Electrical Wiring
Electrical Requirements
The LED driver must be suppled with 120-277 VAC, 50/60 Hz per product label
and connected roan individual properly grounded branch circuit, protected by a
15 or 20 ampere circuit breaker.
Grounding Instructions
Thegrounding and bonding of the overall system shall be done in accordance
with National Electric Code (NEC) Article 600 and local codes.
Note: This equipment has been tested and land to comply with the limits
for a Class A digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial enykonment. This
equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the
user will be required tocorrect the interference at his own expense.
Please connect the input wire in correct way, white is ACN, black is
ACL, green is GROUND connection.
Please also make sure the wire connection is fixed perfectly before using.
CERTIFICATE OF COMPLIANCE
UL CERTIFICATION
Certificate Number: E483348
Report Reference: E483348
Issue Date: 2020-FEBRUARY-27
Additional Information:
See the M. Online Certifications Directory at
www.ul.com/database for additional information.
Only those products bearing the UL Certification Mark should be considered as
being covered by UL’s Certification and Follow-Up Service.
Look for the UL Certification Mark on the product.
READ THOROUGHLY BEFORE INSTALLATION
WARNING FIXTURES MUST BE GROUNDED and installed in accordance with the
National Electrical Code and all local codes. Failure to do so may increase
the J PERSONAL INJURY, PROPERTY DAMAGE, FIRE AND DEATH.
WARNING! Dangerous voltage exist within the unit and all precautions
usually observed in handling high voltage equipment should be observed when
replacing light engine or otherwise servicing luminares. Disregarding this
warning could result in electrical shock and possible injury to the individual
installing or servicing this equipment. Installation, service and maintenance
of luminaires should be done by a alified tic sed electric] CAUTION! To
reduce the risk of death, personal injury or property damage from fire,
electric shock, falling parts, cuts/abrasions, and other hazards please read
all warnings and instructions included with and on the fixture box and all
fixture labels.
NOTE!
– This equipment is only for professional installation. Non-professional
personnel shall not remove or install the equipment.
– To avoid damage,falling,electric shock or fire, please do not modify the
lamp or replace accessories without confirming with the supplier.
– Maintenance/installation and replacement the lamps , please confirm to cut
off the power supply, and the lamps have set up a cooling. Please make sure
the lamps properly installed before processing power.
– Ensure the accurate and reliable connection.
– Ensure that the product around the vent, the lamp cannot violate any fire
prevention regulations when using.
Carefully read these instructions before installing product and keep it for
future reference. If you do not understand these instructions, before starting
any work, contact service01@hi-hyperlite.com or 855-688-7879.
FOOTCANDLE LIGHT GUIDE
Footcandles are the most common unit of measure used by lighting professionals to calculate light levels in businesses and outdoor spaces. A footcandle is defined the illuminance on a one square foot surface from a uniform source of light. The Illuminating Engineering Society (IES) recommends the following footcandle levels to ensure adequate illumination and safety for occupants. Below is a guideline for common areas to assist in achieving appropriate light levels with the greatest energy-efficiency. This guide is a collaborative effort of Energy Trust of Oregon and the Lighting Design Lab, Seattle, Washington.
NOTES:
- This guide is based on information gathered from the IES ‘The Lighting Handbook’ 10th Edition. It is highly recommended that all lighting professionals refer to the full IES guide when specifying lighting projects.
- At least half of users are in the 25 – 65 age range
- Horizontal—horizontal plane that average maintained foot-candles are measured.
- Vertical—vertical plane the average maintained foot-candles are measured.
- It is the responsibility of the to determine and provide appropriate lighting levels for each space.
Web: www.hi-hyperlite.com
Email: seryice01@hi-hyperlite.com
Tel: +1(855) 688 7879
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>