BuckeyeStargazer EAF-TV Bracket Straightforward Instruction Manual

BuckeyeStargazer EAF-TV Bracket Straightforward

Product Information

Specifications

• Product Name : EAF-TVis
• Bracket Type : TVis
• Installation Method : Straightforward
• Tools Required : Small diameter Philips head screwdriver, 1.5mm hex key

Product Usage Instructions

Step 1: Bracket Mounting

1. Choose a suitable location for mounting the EAF-TVis bracket. Ensure it is compatible with your TV and provides a clear line of sight for the remote control.
2. Using the small diameter Philips head screwdriver, insert and tighten the screws provided with the bracket into the designated holes on the back of your TV. Make sure the bracket is securely attached.

Step 2: Adjustment

1. Once the bracket is mounted, use the 1.5mm hex key to adjust the angle of the bracket. This allows you to find the optimal position for your TV remote control signal reception.
2. Rotate the bracket clockwise or counterclockwise to achieve the desired angle.

Step 3: Finalizing Installation

1. After adjusting the bracket, double-check that it is securely fastened to your TV.
2. Ensure all connections and cables are properly routed and organized.

Step 4: Testing

1. Turn on your TV and test the functionality of the remote control.
2. If you experience any issues with the signal reception, repeat steps 2 and 3 to adjust the bracket angle.

FAQ (Frequently Asked Questions)

• Q: Can I install the EAF-TVis bracket on any type of TV?
  A: The EAF-TVis bracket is compatible with most TV models. However, it is recommended to check the compatibility before installation.

• Q: What should I do if the bracket is not securely attached to my TV?
  A: Make sure you have tightened the screws properly. If the issue persists, consult the user manual or contact our customer support for assistance.

• Q: Can I adjust the bracket angle after installation?
  A: Yes, you can use the 1.5mm hex key to adjust the bracket angle even after installation.

EAF-TVis Installation Instructions

Installation of the EAF-TVis bracket is straightforward and requires only a few simple steps. Tools needed : small diameter Philips head screwdriver, 1.5mm hex key

STEP 1

• Rotate the scope or focuser so that the focuser pinion shaft is on top. Remove the single coarse focus knob from the right side of the focuser, as viewed from behind the telescope.
• Locate included (1) M4x10mm flat head screw.
• Slide the M4x10mm screw through the cutout on the side of the coupler through the round hole on the end of the coupler (be careful not to reverse the coupler and mistakenly slide the screw through the beveled EAF pinion side).
• Fasten the coupler to the focuser pinion shaft using a small diameter philips screwdriver.
• In order to help prevent the M4x10mm screw from working loose from the focuser, tighten the small set screw to help hold it in place (do not overtighten). Also, it may be necessary to put a very small amount of removeable (blue) thread locker on the M4x10mm screw to keep the screw in place.

STEP 2

• Locate included (2) M4x10mm flat head screws.
• Fasten the bracket to the focuser using the M4x10mm flat head screws.

STEP 3

• Hold the EAF up to the two bracket holes on the end. Rotate the focuser pinion shaft so that the flat of the coupler matches the orientation of the flat on the EAF pinion shaft.
•  Slide the EAF pinion shaft into the coupler. Fasten the EAF to the bracket using the ZWO supplied M4 screws provided with the EAF.
• Note : both the bracket mounting holes and EAF mounting holes are slots so that there can be some adjustments to the position of the bracket and EAF. Try to align the EAF pinion with the focuser pinion.

STEP 4
Secure the coupler to the EAF pinion shaft by tightening the two coupler set screws using a 1.5mm hex key. Make them snug but do not over-tighten.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>