RAB H17XL UFO LED High Bay Instructions
- June 3, 2024
- RAB
Table of Contents
RAB H17XL UFO LED High Bay
MODELS NO:
H17
H17XL
IMPORTANT
READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE
REFERENCE.
RAB fixtures must be wired in accordance with the National Electrical Code and
all applicable local codes. Proper grounding is
required for safety. THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE
APPLICABLE INSTALLATION CODE BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND
OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED.
WARNING: Make certain power is OFF before installing or maintaining fixture. No user serviceable parts inside.
HOOK MOUNTING
- Screw the Hook into the Fixture, tighten and fix it. (Fig. 1)
- Hang the Fixture on the Ceiling Hook or chain. (Fig. 2)
- After installation, connect the wire of the fixture to the mains. Use appropriate UL approved wire connectors as required by code to complete wiring.
CEILING MOUNTING (WITH ACCESSORY KIT)
- Mark with a pen or sharp tool on the mounting surface and drill.
- Fix Screws into the holes with a hammer.
- Align the Bracket Holes with Screw Holes (Fig. 3), push the Fixture to one side, and tighten Screws.
- After installation, connect the wire of the fixture to the mains. Use appropriate UL approved wire connectors as required by code to complete wiring. By adjusting the bracket screws, users can adjust 50° to the left or right vertically. (Fig. 4).
PENDANT MOUNTING (WITH ACCESSORY KIT)
- Unscrew the Nuts on 1/2” NTP. (Fig. 5)
- Insert 1/2” NTP stem into the Bracket Hole and re-screw the Nuts. (Fig. 6)
- After installation, connect the wire of the fixture to the mains. Use appropriate UL approved wire connectors as required by code to complete wiring. By adjusting the bracket screws, users can adjust 50° to the left or right vertically. (Fig. 4).
WIRING
RISK OF FIRE. Universal voltage driver permits operation at 120V thru 277V, 50 or 60 Hz. Drop down supply wires must be at least 9” long to allow fixture removal. For non-dimming (on/off ), Electronic Low Voltage (ELV) and TRIAC dimming follow the wiring directions in Fig. 7. For 0-10V dimming, Fig. 8.
- Connect the GROUND wire from fixture to supply ground.
- Connect black fixture lead to (+) LINE supply lead.
- Connect white fixture lead to (-) COMMON supply lead.
FIELD-ADJUSTABLE CCT & WATTAGE
The fixture has 2 selectable CCTs and 3 wattages. To access, remove the waterproof gasket, adjust the CCT and Power switches as needed.
Factory settings:
- H17: 150W and 4000K
- H17XL: 240W and 4000K
MOTION SENSOR INSTALLATION (PURCHASED SEPARATELY)
- Unscrew the 1/2” Knockout out with a screwdriver and screw the Sensor Kit on.
INSTRUCTIONS
CLEANING & MAINTENANCE
CAUTION: Be sure fixture temperature is cool enough to touch.
Do not clean or maintain while fixture is energized.
- Do not open fixture to clean the LED. Do not touch the LED.
- Do not touch reflector, lens or trim cone.
- Do not clean any fixture surface with wood-base cleaning material such as paper towels or tissues.
TROUBLESHOOTING
- Check that the line voltage at the fixture is correct. Refer to wiring directions.
- Is the fixture grounded properly?
Note: These instructions do not cover all details or variations in equipment nor do they provide for every possible situation during installation, operation or maintenance.
RAB Lighting is committed to creating high-quality, affordable, well-designed and energy-efficient LED lighting and controls that make it easy for electricians to install and end users to save energy. We’d love to hear your comments. Please call the Marketing Department at 888-RAB-1000 or email: marketing@rablighting.com
Easy Answers
rablighting.com
Visit our website for product info
Tech Help Line
Call our experts: 888 722-1000
e-mail
Answered promptly – sales@rablighting.com
Free Lighting Layouts
Answered online or by request
RAB WARRANTY: RAB’s warranty is subject to all terms and conditions found at rablighting.com/warranty.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>