Sunbeam GCSBCL-317 Anti-Drip Non-Stick Soleplate Iron Instruction Manual
- June 3, 2024
- Sunbeam
Table of Contents
Sunbeam GCSBCL-317 Anti-Drip Non-Stick Soleplate Iron
IMPORTANT SAFEGUARDS
When using electrical appliances, basic safety precautions should always be followed including the following:
Read All Instructions Before Use
- Use iron only for its intended use.
- To protect against risk of electric shock, do not immerse the iron in water or other liquids.
- The Fabric Select Setting and Steam Lever should always be turned to OFF before plugging or unplugging from outlet. Never yank cord to disconnect from outlet; instead, grasp plug and pull to disconnect.
- Do not allow cord to touch hot surfaces. Let iron cool completely before storing. Loop cord loosely around iron when storing.
- Always disconnect iron from electrical outlet when filling with water, cleaning, emptying or when not in use.
- Do not operate iron with a damaged cord or if the iron has been dropped or damaged. To avoid the risk of electric shock, do not disassemble the iron. Take it to an authorized service center for examination and/or repair. Incorrect reassembly can cause a risk of electric shock when iron is used.
- Close supervision is necessary for any appliance being used by or near children. Do not leave iron unattended while plugged in, turned on or on an ironing board.
- Burns can occur from contact with hot metal parts, hot water or steam. Use caution when you turn a steam iron upside down – there may be hot water in the reservoir.
- If the iron is not operating normally, disconnect from the power supply and have the iron serviced by an authorized service center or call Customer Service at 1 800-667-8623.
- Your SUNBEAM® iron is designed to rest on the heel rest. Do not leave the iron unattended.
- Do not set the iron on an unprotected surface, even if it is on the heel rest.
- This is a high wattage appliance. To avoid a circuit overload, do not operate another high wattage appliance on the same circuit.
- If an extension cord is absolutely necessary, a 15-ampere cord should be used. Cords rated for less amperage may overheat. Care should be taken to arrange the extension cord so that it cannot be pulled or tripped over.
FOR PRODUCTS PURCHASED IN THE UNITED STATES AND CANADA
To reduce the risk of electrical shock, this appliance has a polarized plug (one blade is wider than the other). This plug fits a polarized outlet only one way; if the plug does not fit fully into the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. Do not attempt to defeat this safety feature.
SAVE THESE INSTRUCTIONS
FEATURES
- SPRAY MIST™ Nozzle
- Water Fill Hole
- Steam Lever
- SHOT OF STEAM® and SPRAY MIST™ Buttons
- Reset Button and Power Light
- Handle
- Fabric Select Setting
- Self Clean Button
- See-Through Water Reservoir/ Maximum Fill Line
- Soleplate
- Storage Strip® Indicator (select models only)
- Cord Wrap (underneath)
- Power Cord
NOTE: The model shown in the manual is for reference only. Your model may differ slightly.
FILLING WATER RESERVOIR (use tap water)
- Turn Steam Lever to (Dry) and Fabric Select Setting to Off. Unplug.
- Raise the Water Fill Hole Cover. Hold the iron at a 45 degree angle and use any easy-pour measuring cup to fill the water reservoir with tap water through the water fill hole. Do not fill water reservoir beyond maximum fill line.
WARNING: To prevent the risk of burns, be careful when filling a hot iron with water. Hot metal parts, hot water and steam can cause injuries.
DRY IRONING
- Ensure Steam Lever is turned to the (Dry) setting.
- Plug the cord into a 120-Volt AC outlet.
- Turn Fabric Select Setting to desired setting. Allow iron to heat for 2 minutes on its heel rest on a stable, protected surface.
NOTE: While Steam Lever is turned to the (Dry) setting, you may still use the SHOT OF STEAM® or SPRAY MISTTM features, as long as the Fabric Select Setting is set to wool, cotton, or linen. Water reservoir must be at least ¼ full of water.
STEAM IRONING
- Fill Water Reservoir and plug the cord into a 120-Volt AC outlet.
- Turn the Fabric Select Setting to desired setting. Allow the iron to heat for 2 minutes on its heel rest on a stable, protected surface. Turn Steam Lever to desired setting.
IMPORTANT: When not ironing, always set the Steam Lever to (Dry) and the Fabric Select Setting to OFF.
SPECIAL FEATURES
SPRAY MISTTM FEATURE is a powerful water spray mist that dampens the
fabric to aid in removing wrinkles from heavy fabrics and for setting creases.
TO USE: Press the Spray MistTM button firmly.
SHOT OF STEAM® FEATURE provides an extra burst of steam for deep
penetration of stubborn wrinkles. You can use this feature while Dry or Steam
ironing as long as the Fabric Select Setting is set to wool, cotton, or linen.
The water reservoir must be at least ¼ full of water. TO USE: Place the
iron on top of the wrinkle and press the Shot of Steam® button each time you
would like an extra burst of steam. The Shot of Steam® feature may be used
continuously in approximately 3-second intervals.
NOTE: Shot of Steam pump may require priming for initial use. To prime
simply push the button firmly 10-15 times repetitively.
VERTICAL SHOT OF STEAM® FEATURE allows iron to function vertically as a
garment steamer.
TIP: When using vertical steam, hang clothing on a hanger for best
results. Hanging curtains and drapes may also be steamed.
TO USE:
- Hold iron vertically near, but not touching the fabric you want to steam. Pull the fabric tight.
- Press Shot of Steam® button in 3-second intervals as you move iron over wrinkles.
WARNING: To prevent burns, keep hands away from the area being steamed.
WARNING: DO NOT steam garments while wearing them; this may result in
injuries.
TIMED AUTO-OFF FEATURE
IF YOU LEAVE IRON ON: Timed auto-off will automatically turn unit off
after 30 minutes. 3-way auto-off (15 min in heeled position)
IMPORTANT: Once timed auto-off activates, power light blinks to indicate
it is in auto-off mode.
TO RESET: Press reset button. if available, otherwise unplug and plug it
back in.
WARNING: Auto-Off is a safety feature and is not a recommended means for
turning iron off.
STORAGE STRIP ® INDICATOR (select models only)
Indicates when the iron is cool enough to store.
Red = Iron is too hot to store.
Black = Iron is cool enough to store.
CAUTION: STORAGE STRIP® indicator should only be used as a guideline.
Iron should always be handled and stored with care.
CARING FOR YOUR IRON AFTER USE
TURNING OFF IRON: Turn Steam Lever to (Dry) and Fabric Select Dial to Off. Unplug. WARNING: NEVER yank power cord when unplugging iron. This can damage the cord. Empty water tank completely after each use
STORING YOUR IRON
- Turn off iron and allow to cool.
- Empty water reservoir after each use for a longer iron life.
- Loosely loop the power cord around the Cord Wrap and Handle and store the iron on its heel rest. IMPORTANT: Wrapping the cord around the iron too tightly can damage the cord.
MAINTAINING YOUR IRON
USING SELF-CLEAN FEATURE: Use the Self-Clean feature once a month to maintain optimal iron performance
- Turn off iron.
- Move Steam Lever back and forth to remove debris and minerals from Steam Valve. This keeps water flowing into the steam chamber.
- Fill water reservoir with tap water to MAX line.
- Plug in iron, set Fabric Select Setting to Linen and heat for 2 minutes.
- Unplug iron. Holding iron over a sink in a horizontal position, press Self-Clean Button and hold. Water will begin dripping from the steam vents. Slowly rock iron side to side and front to back for 30 seconds. Dip nose of the iron slightly below the rear to circulate water. Release Self-Clean Button after one minute.
- Open fill cap and empty remaining water. Carefully dry soleplate with a towel.
- Plug in iron and set Fabric selection to Linen and Heat for 2 minutes to dry out completely. Set Fabric Select Setting to Off, unplug the iron, and allow to cool.
CLEANING SOLEPLATE: Clean soleplate after every 30 uses, or more
frequently if starch is used or build-up starts to accumulate. Before
cleaning, ensure iron is unplugged and cool.
WARNING: Do not immerse in liquids or use abrasive cleansers or scouring
pads to clean the soleplate. This will damage the finish.
ANTI-CALCIUM SYSTEM (select models only)
Anti-calcium is a permanent system located inside the water reservoir to
eliminate impurities. Ensure your iron has this feature before performing
these steps.
TO PROLONG EFFICIENCY, FOLLOW THESE STEPS ONCE A MONTH OR After Every 30
Uses:
- Turn off iron.
- Add 1 teaspoon of salt to ¾ cup water and fill water reservoir with this solution.
- Leave solution in water reservoir for 15 minutes, shake occasionally, and then empty through the fill hole or through the “clean method”.
- Fill water reservoir again with salt water solution, shake and empty after 15 minutes.
- Fill water reservoir with fresh water to rinse and empty.
IRONING TIPS
- Before ironing, check the garment label and follow manufacturer’s instructions. If no instructions, start with a low-heat setting and test by ironing a small area, and gradually increase heat.
- Sort garments by fabric type. Iron articles requiring a low-temperature setting and gradually work up the temperature range.
- When changing from a high-temperature setting to a lower one, allow 5 minutes for change.
- When steam ironing, use long, slow passes over the fabric to allow the steam to penetrate the fabric and the heat of the soleplate to dry the moisture.
- Iron linen garments inside out to prevent shine. An ironing cloth or cotton fabric can be used to reduce shine.
- If the garment is lined, use a low heat setting.
- Ensure zippers are closed and flap is flat. Iron over the flap, holding the garment taut.
- Spray starch makes the job easier.
IRONING SHIRTS
- Begin with the collar and work toward the middle from the outer edges. Iron lengthwise, not in circles.
- Lay shoulder over narrow edge of the board and iron one side of the front. Then iron the shoulder, across the back (below the collar line), the other shoulder and the remainder of the front.
- Iron sleeves and cuffs, working down from the underarm seams. To remove creases, shift the double layer of sleeve fabric and iron out.
- Iron body of the garment, from half of the front around the back, then second half of front. If your shirt does not open, slip over end of ironing board and iron front and back in turn.
IRONING PANTS
- Begin with the waistband and inseam area, then pockets and cuffs.
- Pull the waistband on the pointy end of the board, as if you’re “dressing” the ironing board. Iron upper-front part of the pants, including the waistband.
- Place pants parallel to the ironing board lengthwise so both legs are facing the same direction. Iron each leg by moving the iron back and forth along the pant leg.
- Take cuff of the leg and bring it over towards the waistband to iron the inner part of the leg. Repeat these 2 steps for the second leg.
TROUBLESHOOTING
3 Year Limited Warranty and Lifetime Limited Soleplate Warranty
Sunbeam Products, Inc. doing business as Jarden Consumer Solutions or if in
Canada, Sunbeam Corporation (Canada) Limited doing business as Jarden Consumer
Solutions (collectively “JCS”) warrants that for a period of three years from
the date of initial retail purchase, this product will be free from defects in
material and workmanship. JCS warrants the iron’s soleplate will be free from
defects in material and workmanship for the life of the iron from the date of
initial retail purchase.
JCS, at its option, will repair or replace this product or any component of
the product found to be defective during the warranty period. Replacement will
be made with a new or remanufactured product or component. If the product is
no longer available, replacement may be made with a similar product of equal
or greater value. This is your exclusive warranty. Do NOT attempt to repair or
adjust any electrical or mechanical functions on this product. Doing so will
void this warranty.
This warranty is valid for the original retail purchaser from the date of
initial retail purchase and is not transferable. Keep the original sales
receipt. Proof of purchase is required to obtain warranty performance. JCS
dealers, service centers, or retail stores selling JCS products do not have
the right to alter, modify or any way change the terms and conditions of this
warranty.
This warranty does not cover normal wear of parts or damage resulting from any
of the following: negligent use or misuse of the product, commercial use,
accident, use on improper voltage or current, use contrary to the operating
instructions, disassembly, repair or alteration by anyone other than JCS or an
authorized JCS service center. Further, the warranty does not cover: Acts of
God, such as fire, flood, hurricanes and tornadoes. Soleplate warranty does
not cover scratches or discoloration of the soleplate finish and only applies
as long as the iron generates optimal heat.
What are the limits on JCS’s Liability?
JCS shall not be liable for any incidental or consequential damages caused by
the breach of any express, implied or statutory warranty or condition.
Except to the extent prohibited by applicable law, any implied warranty or
condition of merchantability or fitness for a particular purpose is limited in
duration to the duration of the above warranty.
JCS disclaims all other warranties, conditions or representations, express,
implied, statutory or otherwise.
JCS shall not be liable for any damages of any kind resulting from the
purchase, use or misuse of, or inability to use the product including
incidental, special, consequential or similar damages or loss of profits, or
for any breach of contract, fundamental or otherwise, or for any claim brought
against purchaser by any other party.
Some provinces, states or jurisdictions do not allow the exclusion or
limitation of incidental or consequential damages or limitations on how long
an implied warranty lasts, so the above limitations or exclusion may not apply
to you.
This warranty gives you specific legal rights, and you may also have other
rights that vary from province to province, state to state or jurisdiction to
jurisdiction.
How to Obtain Warranty Service
In the U.S.A
If you have any question regarding this warranty or would like to obtain warranty service, please call 1.800.458.8407 and a convenient service center address will be provided to you.
In Canada
If you have any questions regarding this warranty or would like to obtain warranty service, please call 1.800.667.8623 and a convenient service center address will be provided to you.
In the U.S.A., this warranty is offered by Sunbeam Products, Inc. doing business as Jarden Consumer Solutions located in Boca Raton, Florida 33431. In Canada, this warranty is offered by Sunbeam Corporation (Canada) Limited doing business as Jarden Consumer Solutions, located at 20 B Hereford Street, Brampton, Ontario L6Y 0M1. If you have any other problem or claim in connection with this product, please write our Consumer Service Department. PLEASE DO NOT RETURN THIS PRODUCT TO ANY OF THESE ADDRESSES OR TO THE PLACE OF PURCHASE.
SUPPORT
For product questions: Sunbeam Consumer Service
USA: 1.800.458.8407
Canada: 1.800.667.8623
2014 Sunbeam Products, Inc., doing business as Jarden Consumer Solutions. All rights reserved. In the U.S., distributed by Sunbeam Products, Inc., doing business as Jarden Consumer Solutions
FAQs
Which soleplate is better for iron?****
The soleplate of the steam iron with the enamel coated has the best gliding qualities of all irons on the market, and it glides over the fabrics with ease. In turn, this speeds up the ironing.
What is the function of soleplate?****
When the customer needs a solid foundation to anchor the motor, a sole plate is provided. Construction/Installation: The Sole Plate is a metal plate with four reinforcement pads that are 3/4″ thick that are welded under each foot of the motor. Its thickness ranges from 1.0″ to 1.5″.
How do you clean sole plate of iron?****
To remove the grime, dampen a paper towel or soft cloth with distilled white vinegar. If any residue is still present, place the cool iron soleplate on a clean paper towel or rag that has been dipped in distilled white vinegar for 15 to 30 minutes. With a fresh towel, remove the remaining substance.
How do you remove rust from iron soleplate?****
Water and Baking Soda: Combine 1 tablespoon water and 2 tablespoons of baking soda to make a paste. The paste should be applied to the iron soleplate using a rubber spatula or a clean towel. With a damp cloth, clean the iron.
What is sole plate in iron?****
To prevent clothing from sticking to the soleplate surface while ironing, it is non-stick. These irons require very little cleaning agent and are simple to maintain.
What is the best way to stop iron from rusting?****
Storage Techniques: To significantly slow down rust, store metal products or parts in a low-moisture area or inside a temperature- and humidity-controlled environment. Desiccant drying agents are also useful in this storage. Galvanize: To prevent rust, galvanising coats iron or steel in zinc.
What is non-stick soleplate iron?****
As a result, you won’t have to wait too long for the iron to heat up. Stick- Free Soleplate. This steam iron’s non-stick soleplate prevents fabric from sticking to the iron and guarantees efficient use.
What is best iron that does not leak?****
This Maytag model, like the majority of the other irons tested, has a self- cleaning setting and an anti-calcium system to keep its steam vents open, functioning properly, and not leaking.
What stops an iron from working?****
A blown fuse is among the most frequent causes of iron press malfunctions. When the iron press’s fuse burns or blows, it may occasionally lose power completely. This is why it’s critical to find a quick solution.
Can steam irons be used without water?****
Yes. Simply unplug your steam iron, allow it to cool, and then empty the water tank to remove the water from the iron. Turn the dial to the dry/steam setting, if your iron has one, or to the “MIN” setting, if it doesn’t have a dry/steam setting.
Video
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>