Sunbeam GCSBTR-100 Compact Non-Stick Soleplate Travel Iron INSTRUCTION MANUAL
- June 3, 2024
- Sunbeam
Table of Contents
Sunbeam GCSBTR-100 Compact Non-Stick Soleplate Travel Iron
IMPORTANT SAFEGUARDS
When using electrical appliances, basic safety precautions should always be followed including the following:
READ ALL INSTRUCTIONS BEFORE USE
- Use iron only for its intended use.
- To protect against risk of electric shock, do not immerse the iron in water or other liquids.
- The Steam Switch should always be turned OFF before plugging or unplugging from outlet. Never yank cord to disconnect from outlet; instead, grasp plug and pull to disconnect.
- Do not allow cord to touch hot surfaces. Let iron cool completely before putting away. Loop cord loosely around iron when storing.
- Always disconnect iron from electrical outlet when filling with water or emptying and when not in use.
- Do not operate iron with a damaged cord or if the iron has been dropped or damaged.
- To avoid the risk of electric shock, do not disassemble the iron. Take it to an authorized service center for examination and/or repair. Incorrect reassembly can cause a risk of electric shock when the iron is used.
- Close supervision is necessary for any appliance being used by or near children. Do not leave iron unattended while plugged in or turned on or on an ironing board.
- Burns can occur from touching hot metal parts, hot water or steam. Use caution when you turn a steam iron upside down – there may be hot water in the reservoir.
- If the iron is not operating normally, disconnect from the power supply and have the iron serviced by an authorized service center. Or call Customer Service at 1.800.458.8407.
- Your Sunbeam® iron is designed to rest on the heel rest. Do not leave the iron unattended. Do not set the iron on an unprotected surface, even if it is on its heel rest.
SPECIAL INSTRUCTIONS
- To avoid a circuit overload, do not operate another high wattage appliance on the same circuit.
- If an extension cord is absolutely necessary, a 15-ampere cord should be used. Cords rated for less amperage may overheat. Care should be taken to arrange the extension cord so that it cannot be pulled or tripped over.
FOR PRODUCTS PURCHASED IN THE UNITED STATES AND CANADA
To reduce the risk of electrical shock, this appliance has a polarized plug (one blade is wider than the other). This plug fits a polarized outlet only one way; if the plug does not fit fully into the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. Do not attempt to defeat this safety feature.
SAVE THESE INSTRUCTIONS
FEATURES OF YOUR COMPACT IRON
- Lens
- Handle Upper
- Temp Select Dial
- Steam Selector
- Water Fill Door
- Tank
- Soleplate
- Shot of Steam Buttons (both sides)
TO FILL THE WATER RESERVOIR (use tap water)
- Make sure the iron is unplugged. Set the Steam Switch to (Dry) and the Temperature Select Dial to OFF.
- Lift the Water Fill Hole Cover.
- Pour tap water into iron water reservoir. Do not fill water reservoir beyond maximum fill level.
WARNING: To prevent the risk of burns, be careful when filling a hot iron with water. Hot metal parts, hot water and steam can cause injuries.
DRY IRONING
- Make sure the Steam Switch is turned to the (Dry)
- Plug the cord into a 120-Volt AC outlet.
- Select the temperature setting you desire using the dial. Allow the iron to heat for 2 minutes. While the iron is heating, make sure it is sitting on its heel rest on a stable, protected surface.
STEAM IRONING
- Follow the instructions for “To Fill the Water Reservoir.”
- Plug the cord into a 120-Volt AC outlet.
- Select the temperature setting you desire using the dial. Allow the iron to heat for 2 minutes. While the iron is heating, make sure it is sitting on its heel rest on a stable, protected surface.
- Turn the Steam Switch to the setting and begin ironing.
Important: When not ironing, always set the Steam Switch to (Dry) and the Temperature Select Dial to OFF.
USING THE IRON’S SPECIAL FEATURES
SHOT OF STEAM® FEATURE
Shot of Steam® Feature provides an extra burst of steam for deep penetration of stubborn wrinkles. You can use this feature while Dry or Steam ironing, but the water reservoir must be at least 1/4 full of water.
TO USE THE SHOT OF STEAM® FEATURE: Place the iron on top of the wrinkle and press the Shot of Steam® button each time you would like an extra burst of steam. The Shot of Steam® feature may be used continuously in approximately 3 second intervals.
CARING FOR YOUR IRON AFTER USE
TURNING OFF YOUR IRON
- Turn the Steam Switch to (Dry) and Temperature Select Dial to Off.
- Unplug the iron from the power source.
WARNING: NEVER yank the power cord when unplugging the iron. This can damage the cord.
STORING YOUR IRON
- Turn off and allow the iron to cool.
- If you do not use your iron on a daily basis, empty the water reservoir after each use for a longer iron life. To do so, unplug the iron, turn the iron upside down, open the fill hole cover, and allow water to flow from the fill hole. Shake the iron gently to remove trapped water drops.
- Loosely loop the power cord around the iron body and store the iron on its heel rest.
Important: Wrapping the cord around the iron too tightly can damage the cord.
MAINTAINING YOUR SUNBEAM® IRON
CLEANING THE SOLEPLATE
Clean the soleplate if starch or other residue accumulate.
TO CLEAN THE SOLEPLATE:
Turn off and allow the iron to cool and then wipe it with a soft, damp cloth.
WARNING: DO NOT use abrasive cleansers, scouring pads or vinegar to clean the soleplate. This will damage the finish.
1 Year Limited Warranty
Sunbeam Products, Inc. doing business as Jarden Consumer Solutions or if in
Canada, Sunbeam Corporation (Canada) Limited doing business as Jarden Consumer
Solutions (collectively “JCS”) warrants that for a period of one year from the
date of purchase, this product will be free from defects in material and
workmanship. JCS, at its option, will repair or replace this product or any
component of the product found to be defective during the warranty period.
Replacement will be made with a new or remanufactured product or component. If
the product is no longer available, replacement may be made with a similar
product of equal or greater value. This is your exclusive warranty. Do NOT
attempt to repair or adjust any electrical or mechanical functions on this
product. Doing so will void this warranty.
This warranty is valid for the original retail purchaser from the date of
initial retail purchase and is not transferable. Keep the original sales
receipt. Proof of purchase is required to obtain warranty performance. JCS
dealers, service centers, or retail stores selling JCS products do not have
the right to alter, modify or any way change the terms and conditions of this
warranty.
This warranty does not cover normal wear of parts or damage resulting from any
of the following: negligent use or misuse of the product, use on improper
voltage or current, use contrary to the operating instructions, disassembly,
repair or alteration by anyone other than JCS or an authorized JCS service
center. Further, the warranty does not cover: Acts of God, such as fire,
flood, hurricanes and tornadoes.
What are the limits on JCS’s Liability?
JCS shall not be liable for any incidental or consequential damages caused by
the breach of any express, implied or statutory warranty or condition.
Except to the extent prohibited by applicable law, any implied warranty or
condition of merchantability or fitness for a particular purpose is limited in
duration to the duration of the above warranty.
JCS disclaims all other warranties, conditions or representations, express,
implied, statutory or otherwise.
JCS shall not be liable for any damages of any kind resulting from the
purchase, use or misuse of, or inability to use the product including
incidental, special, consequential or similar damages or loss of profits, or
for any breach of contract, fundamental or otherwise, or for any claim brought
against purchaser by any other party.
Some provinces, states or jurisdictions do not allow the exclusion or
limitation of incidental or consequential damages or limitations on how long
an implied warranty lasts, so the above limitations or exclusion may not apply
to you.
This warranty gives you specific legal rights, and you may also have other
rights that vary from province to province, state to state or jurisdiction to
jurisdiction.
How to Obtain Warranty Service
In the U.S.A
If you have any question regarding this warranty or would like to obtain warranty service, please call 1.800.458.8407 and a convenient service center address will be provided to you.
In Canada
If you have any question regarding this warranty or would like to obtain
warranty service, please call 1.800.667.8623 and a convenient service center
address will be provided to you.
In the U.S.A., this warranty is offered by Sunbeam Products, Inc. doing
business as Jarden Consumer Solutions located in Boca Raton, Florida 33431. In
Canada, this warranty is offered by Sunbeam Corporation (Canada) Limited doing
business as Jarden Consumer Solutions, located at 20 B Hereford Street,
Brampton, Ontario L6Y 0M1. If you have any other problem or claim in
connection with this product, please write our Consumer Service Department.
PLEASE DO NOT RETURN THIS PRODUCT TO ANY OF THESE ADDRESSES OR TO THE PLACE OF
PURCHASE.
For product questions: Jarden Consumer Service
USA: 1.800.458.8407
Canada: 1.800.667.8623 www.sunbeam.com
© 2010 Sunbeam Products, Inc. doing business as Jarden Consumer Solutions. All rights reserved. Distributed by Sunbeam Products, Inc. doing business as Jarden Consumer Solutions, Boca Raton, Florida 33431
FAQs
Which property is the most suitable for the iron sole plate?
The soleplate of the steam iron with the enamel coated has the best gliding qualities of all irons on the market, and it glides over the fabrics with ease. In turn, this speeds up the ironing.
How do you store an iron after use?
The water reservoir should be emptied and the iron unplugged after each use so that any leftover heat from the iron can help to dry it out. After the iron has cooled, place it in a secure location and store it upright in a cool, dry area.
Which soleplate is best for dry iron?
The best soleplates for ironing are made of stainless steel because they are the simplest to clean. Ceramic soleplates aid in preventing scorch marks on clothing, but they also tend to wear out more quickly due to their unique coating, which can eventually wear off.
What is non-stick soleplate iron?
As a result, you won’t have to wait too long for the iron to heat up. Stick- Free Soleplate. This steam iron’s non-stick soleplate prevents fabric from sticking to the iron and guarantees efficient use.
How do you clean an iron plate?
Simply make a paste by combining some baking soda with a small amount of water. The soleplate of the iron should then be scrubbed with this paste using a soft brush or towel. Simply wipe it away with water. Before using the iron, make sure the paste has been completely removed and allowed to dry.
Is non-stick cast iron good?
Even well-seasoned cast iron pans sometimes struggle to keep some foods from sticking, despite the fact that they are objectively much more durable and versatile than nonstick skillets. Even with little to no oil, nonstick pans keep food from sticking and are simpler to maintain.
How do you clean a burnt non stick iron plate?
Making a paste out of equal parts vinegar and baking soda, rub the soleplate with small circular motions using a clean microfiber cloth dipped in the paste. If there is any paste left over, thoroughly wipe it off with a clean microfiber cloth dipped in distilled water (especially important if your water is hard).
How do you clean an iron soleplate with salt?
On the ironing board, spread a towel and a teaspoon of sea salt. Iron over the salty surface after setting the iron to its highest temperature without adding any steam. The salt will attract any dirt, making the soleplate clean.
What is soleplate iron?
To prevent clothing from sticking to the soleplate surface while ironing, it is non-stick. These irons require very little cleaning agent and are simple to maintain.
What is the best way to remove rust from cast iron?
Submerge your pan in a solution made of equal parts basic white vinegar and water. For really large pans, use a bucket or plug the sink; the vinegar mixture should cover the entire skillet. Up to eight hours can be spent soaking it, but Whitehead advises checking it frequently. It could be completed in just one.
Video
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>