TAOGLAS TGX.04 Series 5G-4G LTE MIMO Cross-Polarized Antenna Instruction Manual

June 3, 2024
TAOGLAS

TAOGLAS logo TGX.04 Series 5G-4G LTE MIMO Cross-Polarized Antenna
Instruction Manual Installation Instructions
TGX.04 Series
MIMO 5G/4G Antenna

Introduction

Following these guidelines will help ensure that your Taoglas TGX.04 antenna is installed correctly. The TGX.04 can be mounted via in 3 different variations;wall mount, pole mount and suction cup mount. All mounting methods are outlined below.

Installation Requirements

Antenna Components: Mounting Plate (x1), Tightening Nut (x1), Antenna Housing (x1), Coaxial Cable(x4) TAOGLAS TGX.04 Series 5G-4G LTE MIMO Cross-Polarized
Antenna fig 1

  • Pole Mount:
    7mm [9/32”] socket wrench or screwdriver, metal mounting clamp (x2)
    Pole Diameter Range: 22mm [0.9”] – 50mm [2”] Metal Mounting Clamp

  • Wall Mount:
    Screwdriver, drill, M4 [Gauge 8] screw (x4), M4 [Gauge 8] washer (x4), 6mm [1/4”] wall mount stud (x4)

  • Suction Cup Mount:
    D40 Suction cups (x4)

Notices

| Caution
To comply with FCC RF Exposure requirements in section 1.1310 of the FCC Rules, antennas used with this device must be installed to provide a separation distance of at least 20 cm from all persons to satisfy RF exposure compliance.
---|---
**| Warning
Do not Operate the transmitter when someone is within 20 cm of the antenna.
Do not operate the equipment in an explosive atmosphere.
**
| European Waste Electronic Equipment Directive 2002/96/EC
Please ensure that your old Waste Electricals and Electronics are recycled do not throw them away into standard waste.

Waiver: This document represents information compiled by Taoglas to the best of our current knowledge. This is not intended to be used as a representation or warranty of fitness of the products described for any particular purpose. This document details guidelines for general information purposes only. When planning installations, always seek specialist advice and ensure that the products are always installed by a properly qualified installer in accordance with applicable regional laws and regulations.
All copyrights, trademarks and any other intellectual property rights related are owned by Taoglas Group Holdings Limited.

Hardware Installation

The TGX.45 antenna can be installed with 3 different methods: pole mount, wall mount, and suction cup mount. Please refer to the appropriate section below that best fits your installation needs

Pole Mount Installation

TAOGLAS TGX.04 Series 5G-4G LTE MIMO Cross-Polarized Antenna fig
2Insert the metal mounting clamps(both top and bottom) through the inner slots of the mounting plate
Loop the mouting straps around the pole at the desired position and tighten the strap until the mounting plate is fixed. Use the self centering feature to guide the mounting plate onto the poleTAOGLAS TGX.04 Series 5G-4G LTE MIMO
Cross-Polarized Antenna fig 3Insert the tightening nut onto the ball joint mount withthe flat surface facing away from the mounting plate
Insert the ball joint firmly into the socket on the back of the antenna body and slide the tightening nut into the antenna housing’s back plate to secure in place. Adjust to the desired antenna orientation on the bal joint and tighten the nut to fix the antenna in place.TAOGLAS TGX.04 Series 5G-4G LTE
MIMO Cross-Polarized Antenna fig 4Optional: Route cables through the cable guide on the mounting plate
Completed Installation
Hardware Installation
The TGX.45 antenna can be installed with 3 different methods: pole mount, wall mount, and suction cup mount. Please refer to the appropriate section below that best fits your installation needs

Wall Mount Installation

TAOGLAS TGX.04 Series 5G-4G LTE MIMO Cross-Polarized Antenna fig
5 Using the mounting plate as a guide mark the position of the screws to the desired location. Drill holes for wall mount studs(6mm[1/4”] diamter, min 25mm[1”] depth) and secure the studs in place. Position the washers into the mounting plate, insert the screws through and into the wall studs. Drive the screws in and tighten to secure the mounting plate in place.
Insert the tightening nut onto the ball joint mount from the mounting plate.TAOGLAS TGX.04 Series 5G-4G LTE MIMO Cross-Polarized Antenna fig
6Insert the ball joint firmly into the socket on the back of the antenna bodyand slide the tightening nut into the antenna housing’s back plate to secure in place. Adjust to the desired antenna orientation on the ball joint and tighten the nut to fix the antenna in place.
Completed Installation.
Hardware Installation
The TGX.45 antenna can be installed with 3 different methods: pole mount, wall mount, and suction cup mount. Please refer to the appropriate section below that best fits your installation needs

Suction Cup Mount Installation

TAOGLAS TGX.04 Series 5G-4G LTE MIMO Cross-Polarized Antenna fig
7Insert the metal mounting clamps(both top and bottom)through the inner slots of the mounting plate.
Using the mounting plate as guide on the mounting surface, align to the desired location of the antenna. Press firmly on each cup to secure in place
Note: Check that the surface to mount on is flat, non-porous, and has been adequately cleaned to ensure proper adhesion.TAOGLAS TGX.04 Series 5G-4G LTE
MIMO Cross-Polarized Antenna fig 8Insert the tightening nut onto the ball joint mount with the flat surface facing away from the mounting plate.
Insert the ball joint firmly into the socket on the back of the antenna body and slide the tightening nut into the antenna housing’s back plate to secure in place. Adjust to the desired antenna orientation on the bal joint and tighten the nut to fix the antenna in place.TAOGLAS TGX.04 Series 5G-4G LTE
MIMO Cross-Polarized Antenna fig 9 Completed Installation

TAOGLAS logoIG-21-8-020-A
taoglas.com

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals