TAOGLAS Synergy Series 9-In-1 Combination Antenna Instruction Manual
- June 5, 2024
- TAOGLAS
Table of Contents
TAOGLAS Synergy Series 9-In-1 Combination Antenna
Introduction
The Taoglas Synergy is an external permanent mount combination antenna. The
Synergy can be provided with combinations of 5G/4G, active GNSS with front end
saw and dual-band Wi-Fi. The Synergy is available with two versions of the
enclosure, one designed specifically for the Ford Interceptor, both supplied
with 3M adhesive, along with an M22 threaded boss for surface attachment. The
Synergy is ideal for vehicle panels of up to 6mm(0.23”) thick with a threaded
boss length of 20.5mm(0.81”).
The Synergy is IP67 rated and includes an O-Ring to seal from any water
ingress.
Electrical Safety
- The Synergy contains an active GPS/GNSS antenna.
- Rated voltage: 3-5VDC Rated current: 20mA maximum
- The supply to this device must be provided with overcurrent protection of 1A maximum.
- Power consumption@1.8V (mA) 8.7 mA
- Power consumption@3.0V (mA) 9.0 mA
- Power consumption@5.5V (mA) 11 mA
Mounting & Location
For prime performance, the Synergy is recommended to be fitted on a conductive metal panel. When fitting on a non-metallic panel, a conductive metal ground plane of suitable size should be fitted underneath the mounting panel to achieve a better level of performance. Optimum ground plane size is 300mm x 300mm(11.8” x 11.8”). When mounting on a vehicle roof panel ensure to mount on a flat surface, and measure for the central position. Care should be taken to mount the Synergy antenna as far as possible from other roof-mounted features such as the aircon unit, light bar etc.
Sealing
In order to ensure that the installation is properly sealed against the
mounting surface care must be taken regarding curvature of the mounting panel.
It is highly recommended to install the antenna on a clean, flat, and level
surface. After installation, the compression of the rubber boot against the
mounting panel should be checked and a small bead of neutral cure silicone
sealant can be applied around the periphery of the mounting boot if required.
Surface Preparation
When preparing to drill the hole, mask the area around the hole position to protect the surface. Drill a pilot hole and increase the hole size to Ø24mm (⅞”). Ensure the drill bit does not contact the headliner. Deburr and clean the area around the hole carefully removing all waste. Remove paint and primer from under panel surface to ensure adequate earth contact by washer and nut. Apply petroleum jelly or paint around cut edge of the hole to prevent corrosion.
Adhesive Patch
On the underside of the antenna, there is a 3M adhesive patch. Peel away the 3M adhesive protection and feed the cables through the hole. Position the antenna over the hole and press down onto the panel with pressure. This adhesion will make ensure will be securely mounted and will also allow for extremely minimal curvature on the roof of a vehicle.
Securing the Mount
A split nut is used to easily fit onto the thread through the cables. The nut is attached from the underside of the panel, it should easily twist onto the thread and then secured in place with a final tighten with a spanner. After tightening, double-check the antenna to make sure that it is properly secured.
Cable Routing and Connection
The Cables supplied are RG-174 for the GNSS feed and TGC-200 for the other feeds. The heat-shrink will denote which cable is which for ease of installation. Connect each individual connector to the correct port of the router, if any cable is unused please fit a 50Ω terminator to the individual connection.
Notices
-
Caution
To comply with FCC RF Exposure requirements in section 1.1310 of the FCC Rules, antennas used with this device must be installed to provide a separation distance of at least 20 cm from all persons to satisfy RF exposure compliance. -
Warning
Do not Operate the transmitter when someone is within 20 cm of the antenna.
Do not operate the equipment in an explosive atmosphere. -
European Waste Electronic Equipment Directive 2002/96/EC
Please ensure that your old Waste Electricals and Electronics are recycled do not throw them away into standard waste. -
Directive 2014/53/EU Radio Equipment Directive (RED)
Harmonized Standards and References:
EN 301 489-1 (V2.2.1): Electro Magnetic Compatibility (EMC) standard for radio equipment and services; Part 1: Common technical requirements. Referencing CENELEC EN 55032 Class B.
Waiver: This document represents information compiled by Taoglas to the best of our current knowledge. This is not intended to be used as a representation or warranty of the fitness of the products described for any particular purpose. This document details guidelines for general information purposes only. When planning installations, always seek specialist advice and ensure that the products are always installed by a properly qualified installer in accordance with applicable regional laws and regulations.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>