ACON AIR 13 HD Rectangular Trampoline with Net and Ladder Instruction Manual

ACON AIR 13 HD Rectangular Trampoline with Net and Ladder

All rights reserved 2022. ACON Finland OY LTD.
All artworks and illustrations are owned by ACON Finland OY LTD.
Copying or reusing them are prohibited by law.

• CAUTION : This is an assembly instruction manual for Aeon AIR 73HD Trampoline. Ensure that you have read and understood the trampoline user manual before assembling this product.
• The owner and/or supervisor of the trampoline are responsible for making all users aware of the practices and information specified in the trampoline user manual.
• ACON Trampoline E-Manuals & more can be downloaded by scanning the QR-code below or from: www.acon-manuals.com/trampoline-manuals

PARTS LISTS

This is a parts list for your trampoline. If any of the parts are missing, please contact ACON customer support.

TRAMPOLINE

1. L-tube for middle leg
   

2. Connecting tube for mid leg
   

3. Steel plate for mid leg
   

4. Top frame corner A
   

5. Top frame corner B
   

6. Top frame tube
   

7. L-tube for end leg
   

8. Connecting tube for end leg
   

9. Jumping mat
   

10. Spring
    

11. Safety pad, long
    

12. Safety pad, short
    

13. Bungee cord, spring pad
    

14. Bolt assembly, trampoline
    
    ENCLOSURE

15. End pole, lower
    

16. Side pole, lower
    

17. Side pole, middle
    

18. Pole, upper
    

19. Pole foam, lower
    

20. Pole foam, upper
    

21. Cap
    

22. Sleeve for enclosure pole
    

23. Net
    

24. Ball bungee cord, net
    

25. Bolt assembly, enclosure
    

26. Adjustable strap, enclosure
    
    OTHER & TOOLS

27. Anchor kit
    

28. User Manual (s)
    

29. Safety instructions card
    

30. Allen Key
    

31. Wrench
    

32. Spring pull tool
    

33. Elastic strap
    

Assembly Instruction

1. Assemble trampoline ends. Tube #6: the side with more spring holes must be faced up. NOTE: lock nut is supposed to stop after a few twists while hand tightening.
   
   
   

2. Connect the trampoline ends with top frame tubes {#6). Tube #6: the side with more spring holes must be faced up. NOTE : lock nut is supposed to stop after a few twists while hand tightening.
   

3. Assemble mid legs.

Steel plates (#3) are purposely a tight fit to install because they play a role in the structural integrity and performance of the trampoline.
Tips to install steel plates (#3):

1. Make sure that the orientation of steel plate (#3) is correct-see the direction of the bends in the ends (turned away from the bottom of the leg assembly).
2. Install one outer bolt first, and only barely hand tighten the nut. Then, install the outer bolt in the opposite end-it may help if you bow the steel plate slightly to better align the bolt holes. Also squeezing/ bending the mid leg assembly by pulling/ pushing in the directions shown in figure below may help. One way to do that is to turn the leg assembly upside down against the ground (on a soft surface) and press down from the center. Hand tighten only.
3. Proceed to install the inner bolts.  

4. Insert the mid leg assemblies into the top frame as instructed below. Please note that the sides of t he frame won’t be straight at this point. They are pulled into t heir final positions after the springs are installed.
   

5. CAUTION! INCORRECTLY INSTALLED PART CAN CAUSE INJURY! Please see the figure below on instructions to align the spacer between the enclosure pole and trampoline leg (arrows up and facing the enclosure pole).
   DO NOT USE POWER TOOLS.
   
   

6. TIGHTEN all the bolts that have been hand tightened in the previous steps.
   Add the plastic protective caps. DO NOT USE POWER TOOLS.
   

7. Connect springs (#70) to the v-rings of the mat (#9) and pull towards yourself with the spring pull tool to connect to frame. NOTE: Skirt of the mat must be above the springs (not displayed in figures below for clarity).
   CAUTION! PINCH PONT. Pay attention to hand position when handling springs.
   
   
   Choose spring setup between two options (see the figures above):
   SETUP 1 : Bouncy and excellent performance. Every other spring is attached to the holes underneath the top frame tubes. Begin the spring installation by attaching the corner springs to the mat and the holes underneath the top frame. NOTE: Only every other hole on the top of the frame will be used in this setup. All of the holes underneath the top frame will be used.
   SETUP 2 : Tighter mat for experienced users. Only the holes on the top of the frame will be used in this setup.

8. Continue the spring installation by adding l spring in each gap, working clockwise around the trampoline until all the springs have been installed.
   CAUTION! PINCH PONT. Pay attention to hand position when handling springs.
   
   + l spring/ lap/ gap. NOTE: Jumping mat skirt is not displayed for clarity.

9. Attach the outer edge of the jumping mat skirt to trampoline frame with elastic strips (#33).
   

10. Attach safety pads (#11 and #12) to t he frame with bungee cords (#13). Tip: using spring pull tool is helpful. If necessary, loosen the upper bolt of t he enclosure pole slightly when placing t he skirt of the safety pad between t he enclosure pole and frame. REMEMBER TO RE-TIGHTEN.
    
    

11. Assemble all enclosure poles as instructed below.
    NOTE : Sliding the sleeve (#22) over the cap can be a tight fit. Connect the assembled poles in to the lower poles.

12. Attach the short side of the net first. Adjust the lower edge of net to the centerline of safety pad as instructed in fig.7 with adjustable straps (part #26). The door opening can be placed on the short or the long side of the trampoline.
    
    

13. ENSURE THAT NO UNDERGROUND UTILITIES SUCH AS ELECTRICAL CABLES ARE PRESENT WHERE YOU INSTALL THE ANCHORS. Screw the anchors (#27)into the ground as instructed below. Fig. 2: Tie the strap of the anchor set over the upper frame of the trampoline. Attach the hook into the loop of the anchor base. Tighten with the ratchet.
    
    
    Your ACON AIR 73 HD is ready for use. Have fun!
    

Dimensions

Product dimensions and ASTM /CE-certified weight limits:


WARNING! maximum user weight: 330 lb (750 kg)

CONTANCT US

EUROPE
Email: customercare.eu@acon24.com
acon24.com

USA & CANADA
Email: customercare.us@acon24.com
Tel: +l {866) 297 5234
us.acon24.com

SWEDEN
Email: kundtjanst@acon24.se
Tel: +46 (08) 12013113
www.acon24.se

FINLAND
Email: acon@acon.fi
Tel: +358 (0)9 42720823
acon.fi

All rights reserved 2022. ACON Finland OY LTD.
All artworks and illustrations are owned by ACON Finland OY LTD.
Copying or reusing them are prohibited by law.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>