GLOBAL INDUSTRIAL 293129, 293130 Wall Mounted Oscillating Fan User Manual
- June 3, 2024
- GLOBAL INDUSTRIAL
Table of Contents
User Manual
Customer Service
US: 1-800-645-2986
WALL MOUNTED OSCILLATING FAN
Models: 293129 / 293130
PLEASE READ AND
SAVE THIS INSTRUCTION.
Attention: Picturesi n theIMareforreference only.
Intended Use:
This product is intended for industrial or commercial applications. Use only
with electrical wiring that is in good working order and that meets applicable
codes and ordinances.If you have any questions whether your wiring is
adequate, consult a qualified electrician.
While using your fan, you should follow the IMPORTANT
INSTRUCTIONS listed below. As part of those instructions, we have used the
word “WARNING” to indicate the level of hazard:WARNING indicates a hazard
which, if not avoided, could result in injury or death.
IMPORTANT INSTRUCTIONS
As with all electrical appliances, basic safety precautions should always be followed to reduce the risk of electric shock, fire, or injury to persons, including the following precautions:
- Read all the instructions before using this fan.
- Use this fan only as described in this manual. Any other use not recommended by the manufacturer may cause electrical shock, fire or injury to persons.
- Do not operate the fan with a damaged power cord or after the fan malfunctions or has been dropped in any manner.
- Use of extreme caution is necessary when any fan is used by or near children, disabled persons or pets and whenever the fan is left operating unattended.
- Do not place the fan on a small, unlevel, uneven or any surface which might allow fan to tip or fall.
- Always unplug fan when not in use, when moving from place to place, when assembling or disassembling parts, and before cleaning.
- The use of attachments, not recommended or sold by the manufacturer, may cause hazards.
- Do not use outdoors.
- To reduce the risk of fire or electrical shock, do not expose to water or rain.
- To reduce the risk of fire or electrical shock, do not use this fan with any solid state speed control device.
- Do not operate the fan with blade guards or any safety device removed.
- Automatically operated device – To reduce the risk of injury, disconnect from power supply before servicing.
- If the power supply cord is damaged, contact your local service center or a qualified electrician to install an appropriate replacement cord to prevent any injury or damage.
- To reduce the risk of injury to persons, install fan at least 2.1m (7 feet) above the floor.
- Avoid the use of extension cords due to risk of fire. If an extension cord must be used, the cord must be minimum 14 AWG and rated not less then 1875 watts.
- Do not run power cord under carpeting. Do not cover cord with throw rugs, runners or the like. Arrange cord away from traffic area where it will not be tripped over.
- Do not insert or allow any object to enter any openings on the fan. Doing so may cause electric shock and/or fire hazard. Avoid contact with moving parts.
- This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
- Children should be supervised to ensure they do not play with the appliance. 22
READ & SAVE THESE INSTRUCTIONS
WARNING: Shock Hazard Use your fan only in dry environments. This fan is
not intended for use in a bathroom, laundry area, or similar locations, or
near sinks, washing machines, swimming pools or other sources of water. Never
locate fan where it may fall into a bathtub or other water receptacle. Do not
use in damp environments such as flooded basements.
WARNING: Hot Surfaces Do not touch fan motor when in use. This motor is
hot when in use, to avoid burns, do not let bare skin touch hot surfaces.
WARNING: Fire Hazard Fans have arcing or sparking parts inside. Do not
use near combustible materials or flammable gases or sources of heat. DO NOT
USE in areas where gasoline, paint or flammable materials are used or stored.
To prevent a possible fire, do not block air intakes or exhaust in any manner.
Do not insert or allow foreign objects to enter any ventilation or exhaust
opening as this may cause an electric shock, fire, or damage the fan.
WARNING: Electrical Shock Hazard Do not use with damaged cord or plug.
Use with adequate electrical system that is up to code.
** CAUTION: to Prevent Electric Shock, this product has a three prong
grounded plug that must be inserted into a matching properly grounded outlet
to reduce the risk of electrical shock. Do not attempt to defeat this safety
feature.
WARNING:** to Reduce the Risk of Fire or Electric Shock, do not use this
product with any solid‑state speed control device.
Fan Assembly
ASSEMBLY INSTRUCTION
Use the following information as a guideline only. It is the user’s
responsibility to be sure the location and the wall surface can handle the
weight of this fan .
The wall fan must be mounted on 12 inch (300mm) thick dry and cement ‑ grouted
firm wall or on 4 by 5 inch wood studs / joists.
Use wall bracket as a template for locating the holes to be drilled.
After determining the hole locations, use an appropriate sized drill bit and,
drill holes through mounting surface.
It is recommended that a minimum of grade 5 fasteners be used.
The following are acceptable surfaces for mounting wall mount assembly.
STEEL SURFACE ‑ When mounting to a steel surface, such as vertical I‑beam,
drill through holes at pre‑marked locations, using a 9/32″ drill bit. Attach
wall mount assembly to mounting surface using 1/4″‑20 hex screw, in
combination with 1/4″ flat washers, 1/4″ lock washers, and 1/4″‑20 hex nuts.
MASONRY SURFACE ‑ When mounting to a masonry surface use a 1/4″ expansion type
bolt or 1/4″ masonry lag with shield designed to handle the weight of this
fan. Drill holes at pre‑marked locations using appropriate sized drill bit as
recommended for the fastener.
Usage:
Fan operation: Always operate the fan in the upright position following all
instructions and recommendations listed in this manual.
Fan location: Place the fan in the area of the room that will provide proper
fan cooling.
Fan connection: Plug fan directly into 120 volt A.C., 60 Hz wall outlet. Be
sure plug fits tightly in outlet. A loose connection may cause overheating and
damage to the plug or fan.
Note: To prevent overloading a circuit, do not plug the fan into a circuit
that is servicing other electrical needs.
Speed control: Select air speed by setting switch to either low-medial-high- off.
- OFF
- LOW
- MED
- HIGH
Care and Maintenance
Cleaning: CAUTION-Before cleaning the fan be sure to disconnect power cord
from the plug. Clean the grille surface with a clean damp cloth. Do not use
harsh chemical or abrasive cleaners. DO NOT IMMERSE THE FAN OR ANY WIRES IN
WATER. Replace front grille before fan use. Allow fan to dry completely before
use. Periodic grille cleaning with a vacuum will prevent dust build up. The
motor is sealed and does not require any interior maintenance, cleaning or
lubrication.
Maintenance: The Internal motor bearings are permanently lubricated at the
factory and do not require any additional lubrication.
Repair: DO NOT OPERATE THE FAN WITHOUT THE GRILLE IN PLACE. DO NOT USE THE FAN
IF IT HAS MALFUNCTIONED OR BECOME DAMAGED IN ANY WAY.
Storage: Keep original carton for storage of the fan. Coil and tie the power
cord to avoid damage during storage.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>