BWT Cosmy 100 Pool Vacuum Cleaner Instruction Manual
- June 16, 2024
- BWT
Table of Contents
BWT Cosmy 100 Pool Vacuum Cleaner
Introduction
System overview
The robotic cleaner sweeps the pool floor and walls collecting dirt and debris
in its filters. This user manual explains how to operate the robotic cleaner,
including cleaning, maintenance and storage procedures. Note: This manual
reviews several different models with variations in components.
Robotic cleaner operation
Once the robotic cleaner is placed in the pool and activated, it operates
according to its program. It moves along the floor and walls of the pool,
covering the entire area of the pool floor and walls. When it has finished its
program, it remains inactive on the pool floor. Power will automatically shut
off. Note: It’s not recommended to stop the pool cleaner prior to cycle end.
Note : Wall climbing is an optional feature. When the wall climbing feature is enabled, the robotic cleaner climbs the wall at intervals according to its internal program. Its ability to climb over stairs in swimming pool is subject to stair geometry and material.
Operating conditions
The robotic cleaner is intended for use in residential swimming pools only and
in the following conditions: (1) Recommended water temperature 22°C-32°C
(72°F-90°F). (2) Water pH : 7.2 – 7.6 (3) Chlorine level: pool is maintained
according to the pool manufacturer’s instructions. (Recommended Chlorine
level: 2-4 ppm) Note: Failure to maintain the pool according to the
recommended operating conditions could prevent the robotic cleaner from
functioning properly.
Components
Operation
Placement of the Power Supply
Place the power supply at least 3.6 meters / 11.8 feet from the pool and at
least 12 cm above ground. CAUTION: The power supply is not water resistant; it
must not be exposed to water or to direct sunlight.
Press the plastic snap on the zip ties in order to release the floating cable.
Use as much cable as needed in the the water.
Before placing the cleaner unit in the water
Make sure there are no people in the pool. Make sure that the filters are
clean. Make sure the pool conditions are met; (see “Operating Conditions” ).
Placing cleaner in the water
Unroll the floating cable. It is recommended to extend a length of cable that
is equal to the pool diagonal size plus an additional two meters. Smooth out
coils or twists in the cable. Connect the floating cable to the socket located
on the power supply. Roll extra cable, no in the pool, near the power supply.
Place the cleaner unit in the pool. Let it sink to the bottom of the pool. Do
not start operation before the robotic cleaner is settled on the pool floor.
CAUTION : Operating the cleaner out of water may cause immediate and severe damage resulting in loss of warranty.
Starting the robotic cleaner
Connect the power supply to the wall socket. The on/off button will lit and
the robotic cleaner will start its cleaning program. If the power supply is
already connected to the wall socket, the on/off button will flash to indicate
that the robotic cleaner is in standby mode. Press the On/Off button in order
to change the above mode (On to Off – standby, or vice versa). Note: if the
full filter indication light is ON make sure to remove and clean the filter
prior to putting the cleaner inside the pool water.
Cleaning cycle
During the cleaning cycle, the cleaner: (1) moves across the pool floor
picking up dirt and debris. (2) Changes direction and rotates automatically
according to the selected program. (3) Climbs the pool walls every few
minutes, as set in its internal program. Note: The robotic cleaner might
occasionally stop moving for a few seconds. This is part of normal operation,
not a malfunction.
Stopping robotic cleaner operation
The robotic cleaner moves automatically to ‘standby’ after every cleaning
cycle and the on/off button starts flashing. To stop the cleaner operation
during a cleaning cycle, press the operation button once. On/off button starts
flashing and the cleaner is in standby mode.
Pulling cleaner unit out of the water
(1) Unplug the floating cable from the power supply. (2) Pull the floating
cable until the unit is close enough to reach the handle. (3) Using the
handle, lift the cleaner out of the pool.
CAUTION : Do not use the floating cable to lift the cleaner out of the
water.
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference that may be
received or that may cause undesired operation. A distance of at least 20 cm.
between the equipment and all persons should be maintained during the
operation of the equipment.
Power Supply
Maintenance and Storage
Cleaning the filters
The two filters must be cleaned after each cleaning cycle. Press the buton to
release the filter and pull it out of the cleaner. Open the filter case. Spray
water on the outer sides of the filter and then spray water towards the inner
side of the filter to clean all the dirt and debris. Reinsert the filter back
into its location.
Storing the robotic cleaner
Follow these instructions to store the robotic cleaner when not in use:
Disconnect the power cord from the wall outlet. Disconnect the floating cable
from the power supply. Make sure that the power supply is not exposed to water
Spread out the floating cable, and roll it. Wash the cleaner unit interior
space with fresh water and let it dry. Roll the floating cable and place it on
the cleaner unit. Caution: Do not roll the floating cable on the handle of the
cleaner unit. Store the robotic cleaner components in a dry, closed location.
Checking water outlet propeller
It is recommended to periodically clean debris and hair from the propeller of
the water outlet: Remove the filters. Remove the screws that hold the water
outlet cover. Remove the water outlet cover. Clean any hairs, dirt, or debris.
Return the cover and fasten it with the screw. Reinsert the filters.
Product Marketing Name(PMN): AQ11091W1
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to two conditions:
(1) This device may not cause harmful interference, and (
2) this device must accept any interference that may be received or that may
cause undesired operation. A distance of at least 20 cm. between the equipment
and all persons should be maintained during the operation of the equipment.
Troubleshooting
CLEANER DOES NOT TURN ON
There is no electricity in the wall socket:
- Disconnect cleaner from the power and control unit.
- Disconnect power supply from the wall socket, wait 30 seconds and reconnect. (3) Turn power on. If not activated, connect the unit to a different wall socket.
Obstacle in the drive system of the cleaner unit:
- Turn the cleaner unit carefully to view the underside.
- Check that the scrubbing brush is not bent/broken.
- Clean and remove obstacles and debris if necessary.
Propeller is seized due to accumulation of hair: Check if the propeller is broken or needs to be cleaned (see “Checking Water Outlet Propeller”).
CLEANER MOVES BUT DOES NOT PUMP WATER
Filters are dirty: (1) Remove the filters and clean them.
Propeller is broken or seized due to accumulation of hair: Check if the
propeller is broken or needs cleaning (see “Checking Water Outlet Propeller”).
CLEANER PUMPS WATER BUT DOES NOT MOVE
Obstacle in the drive system of the cleaner unit:
- Turn the cleaner unit carefully to view the underside.
- Check that the scrubbing brush is not bent/broken.
- Clean and remove obstacles and debris if necessary.
CLEANER STARTS AND SHUTS OFF AFTER A SHORT TIME
Filters are dirty:
- Remove and clean the filters.
- Restart the robot and try again.
Propeller is broken or seized due to accumulation of hair:
- Remove the top screws on the top outlet.
- Check if the propeller is broken or needs to be cleaned.
Obstacle in the drive system of the cleaner unit:
- Turn the cleaner unit carefully to view the underside.
- Check that the scrubbing brush is not bent/broken.
- Clean and remove obstacles and debris if necessary.
CLEANER DOES NOT PICK UP DIRT
Filters are dirty or have holes.
Clean as needed and verify that there are no holes in the filters.
Propeller is broken or seized due to accumulation of hair.
Check if the propeller is broken or needs cleaning (see “Checking Water Outlet
Propeller”).
CLEANER UNIT DOES NOT COVER THE ENTIRE POOL
Clean the filters.
- Verify that there is enough length of the floating cable in the water to reach the far end of the pool.
- Make sure that the floating cable is properly spread out and is not tangled.
Propeller is broken or seized due to accumulation of hair:
- Remove the top screws on the top outlet.
- Check if the propeller is broken or needs cleaning.
THE CLEANER DOES NOT CLIMB WALLS
- Verify that your robotic cleaner is not a floor-only model.
- Verify that Program 1, floor cleaning only, is selected on the power supply unit.
- Make sure to clean the filters
- Make sure propeller isn’t broken or tied up to debris/hair.
Warning
- Do not stay in the pool and remove any and all items from the pool before operating the robotic pool cleaner. Do not leave the robot inside the pool if unused.
- The power supply must be connected through a Ground Fault Current Interrupter (GFCI USA) or a Residual Current Device (RCD Europe) not exceeding 30 mA.
- The connection to the power must meet local and national wiring rules.
- All parts must be replaced with original parts supplied by Aquatron Robotic Technology.
- Keep out of children’s reach.
Warranty
2 YEARS WARRANTY POLICY
In application of the terms of Legislative Royal Decree 1/2007 of 16 November
which approved the Revised Text of the Consumer and User Protection Act, BWT
offers a two-year product warranty to consumers from the date on which they
are delivered by the vendor, subject to the terms and conditions described in
this warranty and without prejudice to the terms of the Royal Decree. This
warranty will be valid in all Member States of the European Union, subject to
the legal limitations in each country where it is enforced, in accordance with
the rules for application. The legal warranty covers all components elements
and accessories, including power supplies, pumps, motors, electric wires,
brushes, belts, handles, wheels, bags, remote controls and other product
components .
Warranty Conditions:
Products may be covered under the legal and sales warranties as long as the
problem is reported by the consumer within two months of becoming aware of it.
In order for the warranty to apply, the consumer must contact:
- Contact with the Authorized Technical Assistance Service referred in the attached list and they will inform you about the procedure, or
- Call the vendor from whom the product was purchased, who will provide you with further information. Authorized Technical Assistance Service BWT recommends (but does not require) that maintenance and repairs be performed by an Authorized Technical Assistance Service of BWT. If the products are assembled, disassembled, handled and/or repaired by anyone who is not an Authorized Technical Assistance provider, the legal or sales warranties will NOT apply. The warranty will NOT be harmed in cases of DIY repairs as detailed and recommended in the instruction manual. This warranty covers the repair or the return and replacement of the product as mandated by law.
All repairs covered under the warranty must be performed by a Technical Assistance Service authorized by BWT. The agents, representatives or distributors, DO NOT have the authority to increase or alter the obligations of the warranty in the name and on behalf of BWT.
Exclusions:
Under no circumstances will the legal or sales warranty provided by BWT be
applicable when the defect or malfunction of the product is due to :
- Unauthorized modifications of the product ;
- Misuse, abuse or negligence ;
- Damages caused by force majeure or fortuitous events;
- Use of salt water levels, higher than 5,000 ppm )0.5%)
- The failure to perform the preventive maintenance indicated in the instruction manual;
- Use of the product in anything other than private, residential pools.
Furthermore, BWT will not be liable under any circumstances and neither the legal warranty nor the sales warranty will apply, for any damages that may or will occur to any pool, including pool’s plaster or pool’s vinyl liner, by reason of the use and/or operation of the BWT pool cleaner.
Download BWT Home App for COSMY THE BOT 200 / 250
Documents / Resources
| BWT
Cosmy 100 Pool Vacuum
Cleaner
[pdf] Instruction Manual
Cosmy 100 Pool Vacuum Cleaner, Cosmy 100, Pool Vacuum Cleaner, Vacuum Cleaner,
Cleaner
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>