GLOBAL INDUSTRIAL 244248 Automatic Label Dispenser User Manual
- October 30, 2023
- GLOBAL INDUSTRIAL
Table of Contents
USER MANUAL
AUTOMATIC LABEL DISPENSER
MODEL NO. 244248
Features
Dispense butt-cut and die-cut labels.
Adjustable sensor for pinpoint accuracy.
Built in label counter.
Speed control knob.
NOTE: Not compatible with clear acetate labels
Specifications
| Model | 244248 |
|---|---|
| Name | Automatic Label Dispenser |
| Voltage | DC 12V |
| Power | 20W |
| IP Protection | IP20 |
| Speed | 50~180rpm |
| Torgue | 2kg-cm |
| Feed Speed | 5~18m/min |
| Label Length | 20mm~230mm |
| Label Width | 6mm~100mm |
| Weight | 3.8kg |
| L/W/H | 320x270x203mm |
| Noise Value | LpA=61.3 dB(A), LwA=72.3 dB(A) |
K=3 dB(A)
Auto Label Dispenser
| Part No. | Part Name | QTY |
|---|---|---|
| 1 | Main Plate | 1 |
| 4 | Panal Board | 1 |
| 5 | Variable Resistor Assembly | 1 |
| 6 | Power Switch | 1 |
| 11 | Monitor Frame | 1 |
| 14 | Circuit Board | 1 |
| 15 | Screw | 4 |
| 16 | On/Off Button | 1 |
| 17 | DC Jack | 1 |
| 19 | Speed Control Knob | 1 |
| 21 | DC Motor | 1 |
| 22 | Screw | 3 |
| 24 | Screw | 6 |
| 25 | Motor Cover | 1 |
| 32 | Screw | 2 |
| 33 | Compression Plate | 1 |
| 35 | Velcro Strap | 1 |
| 38 | Axis | 1 |
| 39 | Guiding Bar | 1 |
| 40 | Screw | 2 |
| 41 | Side Guide | 2 |
| 45 | Take-Up Hub Roller | 1 |
| 46 | Screw | 1 |
| 47 | Spring Clip | 1 |
| 50 | Spool Rod | 1 |
| 51 | Core Holder | 2 |
| 52 | Shield | 2 |
| 55 | Sensor Bracket | 1 |
| 56 | Knob | 3 |
| 57 | Collar | 1 |
| 58 | Spring | 1 |
| 59 | Nut | 1 |
| 60 | Sensor | 1 |
| 61 | Screw | 2 |
| 62 | Wire Clip | 1 |
| 63 | Self-Adhesive Wire Clip | 2 |
| 65 | Rubber Foot | 8 |
| 68 | AC Adapter | 1 |
Keep tool well oiled and clean. Please order parts by number and name.
OPERATING INSTRUCTIONS
Install 51 core holders in each side of label roll.Put the label roll to the 50 spool rod.Secure the label roll with 58 spring ,52 shield, and 57 collar.Tighten collar with 56 knob.
Loosen the knob in front of tool so it is easier to feed label under 39 guiding bar then between the 33 compression plate and main plate as shown.
Remove 47 spring cilp.Feed label over metal plate in front of the tool.Separating the liner from the label.Coin the liner to 45 take-up hub roller.Slide 47 spring clip back on over the liner.
Plug in the AC adaptor to the tool and wall socket.Turn the power on( 16
on/off button in the back of tool) first and then press 06 power switch in
front of tool.The light on top of power switch turns green.
Type A plug adaptor is included.If you use different type of plug or socket in
your location, please obtain an appropriate plug adapter in local store.
Sensor can be moved backward or forward by adjusting 56 at side.Sensor can also be moved to the left or to the right by hand.Adjust the sensor according to the width and length of label to achieve smooth operation as labels are removed.
To apply proper amount of tension for proper label feeding and detection, raise 56 knob up to increase tension,then tighten the knob.
Label feeding speed can be adjusted by turning 19 speed control knob.Turn clocwise to increase speed.Turn counter-clockwise to decrease speed.
Always turn off the tool and remove the plug from socket when not in use.
Turn on the on/off button at back of dispenser after install the label sticker.The monitor and power light turn red meaning the dispenser is ready to be used. Set up the speed and press the power switch at front, the power light turns green meaning the dispenser is in use.
Error Status / Troubleshooting
- “Err01” shown on monitor meaning the motor is over loading due to external causes or any other elements. The motor goes into protective mode.
- “Err02” shown on monitor meaning the sensor does not detect the label sticker for 13 seconds and it goes into protective mode.
- Turn on the power switch again to re-operate the tool when“Err01”or“Err02”appears.The quantity before the error appears will pop up once re-starting the power.If you want to start figure from 0,please press the power switch in front of tool for 3 seconds .If the error signal still shown,please contact service team.
- Turn off the on/off button at back of tool to stop the machine if urgency happened.
Photoelectric Sensor
Documents / Resources
|
GLOBAL INDUSTRIAL 244248 Automatic Label
Dispenser
[pdf] User Manual
244248 Automatic Label Dispenser, 244248, Automatic Label Dispenser, Label
Dispenser, Dispenser
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>